Home > Land Rover > Automobile > Land Rover 90 110 Workshop Rover Manual

Land Rover 90 110 Workshop Rover Manual

Here you can view all the pages of manual Land Rover 90 110 Workshop Rover Manual. The Land Rover manuals for Automobile are available online for free. You can easily download all the documents as PDF.

Page 391

REAR DIFFERENTIAL - ONE TEN 151 I 
&:>. ...+, 27. Remove  the  differential bearing cones using Ir ;.:.s;,: remover 18G 47 BL and adaptors 1 and 2 and 
press 47. 
28. Withdraw thc shim  washers  fitted  between the 
bearing  cones and the differential  casings. 
, .;:::;a ..., :>,, I..*,..” 34.  Withdraw the outer  bearing  cone. 
35.  Extract  the  pinion inner bearing  cup and  shim 
washers  from  the  casing. Note 
the shim washer 
thickness.  Remover 
S 123 A. 
36. Extract the pinion outer bearing...

Page 392

151 I REAR DIFFERENTIAL- ONE TEN 
INSPECTION 
38. Examine  all components  for  obvious  wear or 
damage. 
39. 
The bearing  cones must bc a press fit on their 
locations,  except  the drive pinion  flange  and 
bearing  which is a slide  fit. 
40. The crown  wheel  and pinion  are supplied  as a 
matched  pair  and must  not  be  interchanged 
separately. 
A new crown  wheel  and pinion  matched  pair may 
be  fitted to an  original gear carrier  casing 
if sound. 
The original  crown wheel  and...

Page 393

REAR DIFFERENTIAL - ONE TEN 
61. Add  0,127 mm (0.005 in),  for bearing pre-load,  to 
the  total  noted 
in the preceding  instruction.  ‘The 
sum  is then  equal  to the  nominal  value of shims 
required  for the  differential  bearings: 
Shims  are 
available in the range 0,07 mm 
(0.003  in), 0,12 mm (0.005 in), 0,25 mm 
(0.010  in) and 0,76 mm (0.030  in). Sclect the total 
value 
of shims  required. 
62.  Remove 
the differential unit and  bearings  and 
place  aside. 
Do not  fit  the shim...

Page 394

151 I REAR DIFFERENTIAL - ONE TEN 
Drive pinion  markings 
76. Check  that the serial  number  marked on the 
pinion  end face  matches  that  marked  on the 
crown  wheel, 
77.  The  markings  on the  end  face  adjacent  to the 
serial  number  are 
of no  significance  during 
servicing. 
78.  The  figure  marked  on the  end  face opposite to  the 
serial  number indicates, 
in thousandths  of an inch, 
the  deviation  from nominal  required  to correctly 
set  the  pinion. 
A pinion  marked  plus...

Page 395

REAR DIFFERENTIAL - ONE TEN 
..:. . .,.  , .! 85a.Where the stylus has  moved down, the amount  is . ... . I ,, ., . . ...I... equivalent to the  thickness  of shims  that must  be 
removed  from  under the pinion  inner cup  to bring 
the pinion  down to the  nominal  position. 
b.Where the sty!us has moved up,  the  amount is 
equivalent 
to the  additional  thickness  of shims 
required  to bring  the pinion  up to the  nominal 
position. 
.. .., ::: I- 
Illustration A. Using  setting  gauge 18G 191...

Page 396

REAR DIFFERENTIAL - ONE TEN 
93. Fit the  pinion oil seal,  lipped  side  first, using 
general  purpose  grease 
or, where available, a 
molybdenum  disulphide based grease on the seal 
lip, using  RO 1008  to drift 
in the seal. 
94. 
Fit the  coupling  flange  and  plain washer  and 
loosely 
fit a  new  flange  nut.  Secure 18G 1205  to 
the  coupling  flange, using slave  fixings. 
95.  Alternately  tighten  the flange  nut and  check 
the 
drive  pinion  resistance  to  rotation  until the...

Page 397

REAR DIFFERENTIAL - ONE TEN El 
109. Prevent  the drive  pinion  from rotating  and check 
the crown  wheel backlash  which must be 0,15 to 
0,27 mm (0.006  to 0.011  in). If the  backlash  is not 
within  the specified  limits, repeat the differential 
backlash  checks, instructions  96 to 102  looking 
for 
possible  errors. 
110. Fit the  differential  cover and new  gasket,  coating 
both  sides 
of the gasket  with Hylomar  PL 32M  or 
an  equivalent  non
-setting sealant. 
Torque  load for fixings...

Page 398

REAR DIFFERENTIAL - NINETY 
FRONT  DIFFERENTIAL 
- NINETY  AND ONE TEN 
OVERHAUL AXLE DIFFERENTIAL  ASSEMBLY 
Service  tools: 
18G 1205 flange  holder  tool; 
18G 191 pinion  height  setting  gauge; 
18G 191-4 universal  setting block; 
18G 47-6 pinion  head bearing removerheplacer; 
LST 106 oil seal  replacer; or 
RO 262757A extractor for pinion  bearing  caps; 
RO 262757-1 replacer-use  with RO 262757A; 
RO 262757-2 adaptor  tail bearing  cap replacer; 
KO 530105 spanner-differential flange  and...

Page 399

REAR DIFFERENTIAL -NINETY 
FRONT  DIFFERENTIAL - NINETY AND ONE TEN E1 
.. .... - ., . .,. ..~H: ., . . ...,. ,.. ... .. 
. 
ST508M 
13. Remove the bolts  and  washers securing the crown 
wheel 
to the  differential  flangc.  Withdraw the 
crown  whecl. 
14. Remove the differential carrier  bearings. 
15. Remove  the circlips  securing  the  differential cross 
shaft. Extract the  cross shaft. 
16. Withdraw thc differential  gears and pinions. 
17. Thoroughly clean  all components. 
ST509M 
INSPECTION...

Page 400

51 
27. Place the differential  housing complete with crown 
28. Fit the bearing  caps  and bolts. Do not fully tighten 
29. Fit the bearing  adjusting  nuts and  adjust to obtain 
30. Tighten the bearing cap bolts. 
wheel 
and bearings 
in the pinion  housing. 
the bolts. 
zero  end
-float. 
REAR  DIFFERENTIAL - NINETY 
FRONT DIFFERENTIAL -NINETY AND ONE TEN 
LI ST512M 
31. Using a dial  gauge  check thc crown  wheel for 
run
-out.  This  should  not exceed 0,10 mm 
(0.004 in). If excessive  run-out is...
Start reading Land Rover 90 110 Workshop Rover Manual

Related Manuals for Land Rover 90 110 Workshop Rover Manual

All Land Rover manuals