Kyocera FS C5350DN User Manual

							Machine Parts 1-1
1 Machine Parts
This chapter provides explanations and illustrations for you to 
determine the parts and their functions. Try to be familiar with 
the names and functions of these parts for correct use and 
optimal performance.
This chapter contains explanations on the following topics:
Components at the Front of the Printer 1-2
Components at the Left of the Printer 1-2
Internal Components 1-3
Components at the Rear of the Printer 1-3
Operation Panel 1-4
Downloaded From ManualsPrinter.com Manuals 
						

							1-2Machine Parts 
Components at the Front of the Printer
1 Operation Panel
2 Front Cover
3 Paper Stopper
4 Top Cover (Top Tray)
5 MP (Multi-Purpose) Tray
6 Paper Cassette
7 Power Switch
Components at the Left of the Printer
8 Left Cover
9 Waste Toner Box
10 Main Charger Units on the Drum Units
11 Magenta Toner Container (M)
12 Cyan Toner Container (C)
13 Yellow Toner Container (Y)
14 Black Toner Container (K)
2
5 6 13
7
4
8
9
10
11 12 13 14
Downloaded From ManualsPrinter.com Manuals 
						

							Machine Parts 1-3
Internal Components
15 Paper Transfer Unit
16 Paper Ramp
17 Duplex Unit
18 Envelope Switch
Components at the Rear of the Printer
19 USB Memory Slot
20 Power Cord Connector
21 Option Interface Slot
22 Network Indicators
23 Network Interface Connector
24 USB Interface Connector
25 Rear Cover
18
19
2021 2223
24
25
15
17
16
Downloaded From ManualsPrinter.com Manuals 
						

							1-4Machine Parts 
Operation Panel
26 Message Display
27 Ready Indicator
28 Data Indicator
29 Attention Indicator
30 Arrow Keys
31 [MENU] Key
32 [OK] Key
33 [GO] Key
34 [Cancel] Key
2627 28
29 30 31
3233 34
Downloaded From ManualsPrinter.com Manuals 
						

							Printing Operation 2-1
2 Printing Operation
This chapter contains explanations on the following topics:
Changing Network Interface Parameters 2-2
Printing a Network Interface Status Page 2-10
Installing the Printer Driver 2-11
Printing from Application Software 2-17
Downloaded From ManualsPrinter.com Manuals 
						

							2-2Printing Operation 
Changing Network Interface Parameters
This printer supports TCP/IP, TCP/IP  (IPv6), NetWare, AppleTalk, IPP, 
SSL Server, IPSec protocols and Security Level. (For details refer to 
Advanced Operation Guide .)
TCP/IP, TCP/IP (IPv6) settings
1Press [MENU] .
2Press U or  V repeatedly until  Network > appears.
3Press Z. Each time you press  U or V , the selection changes. Refer 
to the explanations below when specifying the settings.
Set this item to  On when you connect to a network using  TCP/IP. 
Submenu has items including DHCP , IP Address, Subnet Mask , 
Gateway and Bonjour .
Set this item to  On when you connect to a network using  TCP/IP 
(IPv6) . Submenu has items including  RA(Stateless)and 
DHCPv6 .
Note  After all network related settings have been done, turn 
the machine OFF and ON again. This is mandatory to make 
the settings effective!
Network        >
>TCP/IP        >
  Off
>TCP/IP (IPv6) >
  Off
Downloaded From ManualsPrinter.com Manuals 
						

							Printing Operation 2-3
TCP/IP
This section describes how to enable the TCP/IP protocol. 
1If TCP/IP is set to  Off, use U  or V to select  On and press  [OK].
2Press  Z. Each time you press U  or V, the selection changes.
3Display the item you want to set and press [OK] . A blinking question 
mark ( ?) appears while you are setting  DHCP and Bonjour. A 
blinking cursor ( _) appears while you are setting  IP Address, 
Subnet Mask  and Gateway .
4Press U or  V to select On or  Off as the setting for  DHCP and 
Bonjour .
For the  IP Address , Subnet Mask  and Gateway settings, press 
U  or V  to move the blinking cursor to the number you want to change 
( 000 to  255). Use  Y and Z  to move the cursor right and left.
5Press [OK].
6Press  [MENU] . The display returns to Ready .
Note  Check with your network administrator for the network 
address settings.
>TCP/IP        >
  On
>>IP Address
 000.000.000.000
>>Subnet Mask
 000.000.000.000
>>Gateway
 000.000.000.000
>>DHCP
  Off
>>Bonjour
  Off
>>Subnet Mask
 0
00.000.000.000
Downloaded From ManualsPrinter.com Manuals 
						

							2-4Printing Operation 
TCP/IP (IPv6)
This section describes how to enable the TCP/IP (IPv6) protocol.
1If TCP/IP (IPv6)  is set to Off, use  U or  V to selecto  On and press  
[OK] .
2Press  Z. Each time you press  U or  V, the selection changes.
3Display the item you want to set and press  [OK]. A blinking question 
mark ( ?) appears while you are setting  RA(Stateless) and 
DHCPv6 .
4Press U or  V to select  On or Off as the setting for  RA(Stateless)  
and  DHCPv6 .
5Press [OK].
6Press  [MENU] . The display returns to  Ready.
NetWare, AppleTalk, IPP, SSL Server, IPSec and Security 
Level settings
1Press [MENU] .
2Press U or  V repeatedly until  Security > appears.
Note  Check with your network administrator for the network 
address settings.
>TCP/IP (IPv6) >
  On
>>DHCPv6
  Off
>>RA(Stateless)
  Off
>>DHCPv6
 ?
Off
>>RA(Stateless)
 ?Off
Security       >
Downloaded From ManualsPrinter.com Manuals 
						

							Printing Operation 2-5
3Press Z. Each time you press  U or  V, the selection changes. Refer 
to the explanations below when specifying the settings.
If you are using  NetWare, AppleTalk , IPP , SSL Server  or IPSec 
to connect to a network, you must enter an administrator ID. 
 
If you are using  NetWare, AppleTalk , IPP , SSL Server  or IPSec 
to connect to a network, you must enter an administrator password.  
Set this item to On when you connect to a network using NetWare . In 
submenu, frame mode can be selected from  Auto, 802.3, 
Ethernet-II , SNAP and 802.2 .
AppleTalk  must be activated ( On) for networking with Macintosh 
computers.
Set this item to  On when you connect to a network using  IPP.
Set this item to  On when you connect to a network using  SSL 
Server . Submenu has items including  DES, 3DES , AES , IPP over 
SSL  and HTTPS .
Set this item to  On when you connect to a network using 
IPSec.
Continued on next page.
Note  The default setting is  3000.
Note  The default setting is 3000.
ID
_
Password
_
>NetWare       >
  On
>AppleTalk
  On
>IPP
  Off
>SSL Server    >
  Off
>IPSec
  Off
Downloaded From ManualsPrinter.com Manuals 
						

							2-6Printing Operation 
Set the Security Level  to High.
NetWare
This section explains the procedure for enabling NetWare.
1Enter the administrator ID and password. Then, if  NetWare is set to 
Off , use U  or V to select On and press  [OK].
2Press  Z.
3Press  [OK]. A blinking question mark ( ?) appears. Each time you 
press  U or  V, the selection changes.
4Display the item you want to set and press  [OK].
5Press  [MENU] . The display returns to  Ready.
>Security Level
  High
>NetWare       >
  On
>>Frame Type
  Auto
>>Frame Type
 ?802.3
>>Frame Type
 ?Ethernet-II
>>Frame Type
 ?SNAP
>>Frame Type
 ?802.2
>>Frame Type
 ?Auto
Downloaded From ManualsPrinter.com Manuals