Kyocera FS C5250DN User Manual

ix
9Your exclusive remedy and the sole liability of Monotype Imaging in 
connection with the Software and Typefaces is repair or replacement 
of defective parts, upon their return to Monotype Imaging.
10 IN NO EVENT WILL MONOTYPE IMAGING BE LIABLE FOR LOST 
PROFITS, LOST DATA, OR ANY OTHER INCIDENTAL OR 
CONSEQUENTIAL DAMAGES, OR ANY DAMAGES CAUSED BY 
ABUSE OR MISAPPLICATION OF THE SOFTWARE AND 
TYPEFACES.
11 Massachusetts U.S.A. law governs this Agreement.
12 You shall not sublicense, sell, lease, or...

x
6Redistributions of any form whatsoever must retain the following 
acknowledgment: This product includes software developed by the 
OpenSSL Project for use in the OpenSSL Toolkit (http:// 
www.openssl.org/)
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT AS IS 
AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT 
NOT LIMITED TO, THE IMPLIED WARRANTIES OF 
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE 
ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR 
ITS CONTRIBUTORS BE LIABLE FOR...

xi
4If you include any Windows specific code (or a derivative thereof) 
from the apps directory (application code) you must include an 
acknowledgement:
This product includes software written by Tim Hudson 
([email protected])
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG AS IS AND ANY 
EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT 
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY 
AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN 
NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE 
FOR ANY...

xii
Compliance and Conformity
This equipment has been tested and found to comply with the limits for a 
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits 
are designed to provide reasonable protection against harmful 
interference in a residential installation. This equipment generates, uses 
and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful interference to radio 
communications. However, there is no...

xiii
CDRH Regulations
The Center for Devices and Radiological Health (CDRH) of the U.S. Food 
and Drug Administration implemented regulations for laser products on 
August 2, 1976. These regulations apply to laser products manufactured 
after August 1, 1976. Compliance is mandatory for products marketed in 
the United States. A label indicating compliance with the CDRH 
regulations must be attached to laser products marketed in the United 
States.
Canadian Department of Communications Compliance...

xiv
Energy Saving Control Function
The device comes equipped with a Sleep Mode where printer functions 
remain in a waiting state but power consumption is still reduced to a 
minimum when there is no activity with the device within a set amount of 
time.
Sleep
The device automatically enters Sleep when 1 minute has passed since 
the device was last used. The amount of time of no activity that must pass 
before Sleep is activated may be lengthened. For more information, refer 
to Sleep Timer (Sleep timer...

xv
Safety Conventions in This Guide
The sections of this guide and parts of the machine marked with symbols 
are safety warnings meant to protect the user, other individuals and 
surrounding objects, and ensure correct and safe usage of the machine. 
The symbols and their meanings are indicated below.
Symbols
The U symbol indicates that the related section includes safety warnings. 
Specific points of attention are indicated inside the symbol.
The   symbol indicates that the related section includes...

xvi
Environment
The service environmental conditions are as follows:
• Temperature: 50 to 90.5 °F (10 to 32.5 °C)
• Humidity: 15 to 80 %
However, adverse environmental conditions may affect the image quality. 
Avoid the following locations when selecting a site for the machine.
• Avoid locations near a window or with exposure to direct sunlight.
• Avoid locations with vibrations.
• Avoid locations with drastic temperature fluctuations.
• Avoid locations with direct exposure to hot or cold air.
• Avoid...

xvii
About the Operation Guide
This Operation Guide has the following chapters:
Chapter 1 - Machine Parts
Explains the names of parts.
Chapter 2 - Printing Operation
Explains how to print from your workstation.
Chapter 3 - Handling Paper
Explains how to choose, handle and load paper.
Chapter 4 - Using the Operation Panel
Explains how to use the operation panel to configure the printer.
Chapter 5 - Maintenance
Explains how to replace the toner container and how to care for your 
printer.
Chapter 6 -...

xviii
Downloaded From ManualsPrinter.com Manuals