Kyocera FS 1370DN User Manual

Maintenance4-3
Replacing the Toner Container
This section explains how to replace the toner container.
1Open the top cover.
2Turn the lock lever to the unlock position. Push the lock lever to the 
position marked by the arrow and pull out the toner container.
CAUTION  Do not attempt to incinerate the Toner 
Container. Dangerous sparks may cause burns.
IMPORTANTDuring toner container replacement, temporarily move 
storage media and computer supplies (such as floppy disks) away 
from the toner container....

4-4Maintenance
3Take the new toner container out of the toner kit. Shake the new 
toner container at least 5 times as shown in the figure in order to 
distribute the toner evenly inside the container.
4Remove the label from the toner container.
5Install the new toner container in the printer. Push firmly on the top of 
the container at the positions marked PUSH, until you hear a click.
Downloaded From ManualsPrinter.com Manuals 

Maintenance4-5
6Turn the lock lever to the lock position.
7Close the top cover.
Maintenance Kit Replacement
When the machine prints 100,000 pages, a message is displayed 
indicating that the maintenance kit should be replaced. The maintenance 
kit must then be replaced immediately. 
To replace the maintenance kit, contact your service technician.
IMPORTANTWhen the waste toner in the drum unit is almost full, 
Waste toner near full is displayed. Replace the maintenance kit.
Downloaded From...

4-6Maintenance
Cleaning the Printer
To avoid print quality problems, the interior of the printer must be 
cleaned with every toner container replacement.
1Open the top cover and front cover.
2Lift the developer unit together with the toner container out of the 
printer.
3Remove the drum unit from the printer by holding the green levers 
with both hands.
Developer 
Unit
Drum 
UnitNoteThe drum unit is sensitive to light. Never expose the 
drum unit to light for more than five minutes.
Downloaded From...

Maintenance4-7
4Place the drum unit flat on a clean, level surface.
5Use a clean, lint free cloth to clean dust and dirt away from the metal 
registration roller.
6On the drum unit, slide the charger cleaner (green) back and forth 2 
or 3 times to clean the charger wire, then return it to its original 
position (CLEANER HOME POSITION).
7When cleaning is complete, return the drum unit to the original 
position.
IMPORTANTDo not place the drum unit on end.
IMPORTANTTake care not to touch the transfer roller...

4-8Maintenance
8Return the developer unit to its position, aligning the guides at both 
ends with the slots in the printer. Then, close the front cover and top 
cover.
9Use a lint free cloth to clean dust and dirt away from the vent on the 
left and the right side of the machine.
Vent
Downloaded From ManualsPrinter.com Manuals 

Maintenance4-9
Prolonged Non-Use and Moving of the Printer
Prolonged Non-use
If you ever leave the printer unused for a long period of time, remove the 
power cord from the wall outlet.
We recommend you consult with your dealer about the additional actions 
you should take to avoid possible damage that may occur when the 
printer is used next time.
Moving the Printer
When you move the printer:
•Move it gently.
•Keep it as level as possible to avoid spilling toner inside the printer.
•Be sure to consult a...

4-10Maintenance
Downloaded From ManualsPrinter.com Manuals 

Troubleshooting5-1
5Troubleshooting
This chapter explains how to handle printer problems, understand error 
messages, and clear paper jams
.
General Guidelines 5-2
Print Quality Problems 5-3
Error Messages 5-5
Ready, Data, and Attention Indicators 5-9
Clearing Paper Jams 5-10
Downloaded From ManualsPrinter.com Manuals 

5-2Troubleshooting
General Guidelines
The table below provides basic solutions for problems you may 
encounter with the printer. We suggest you consult this table to 
troubleshoot the problems before calling for service repairs.
Tips
Printer problems may be solved easily by following the tips below. When 
you have encountered a problem that cannot be solved following the 
guidelines above, try the following:
•Restart the computer you are using to send print jobs to the printer.
•Obtain and use the latest...