Kyocera FS 1100 User Manual

							Troubleshooting5-9
Cleaning Paper Jams
If paper jams in the paper transport system, or no paper sheets are fed 
at all, the printer automatically goes offline, and the Jam indicator will 
light.  Status Monitor  or COMMAND CENTER  can indicate the location of 
the paper jam (the component where the paper jam has occurred). 
Remove the paper jam. After removing the paper jam, the printer will 
resume printing.
Possible Paper Jam Locations
The figure below shows the printers paper paths including the optional 
paper feeder. The locations where paper jams might occur are also 
shown here, with each location explained in the table below. Paper jams 
can occur in more than one component on the paper paths.
Paper jam location Description Reference page
A Paper jam at the  MP tray. page 5-10
B Paper jam at the  paper cassette. The cassette number can be 1. page 5-11
C Paper jam inside the  duplex section. page 5-12
D Paper jam inside the printer. page 5-13
E Paper jam at the  rear cover. page 5-15
Downloaded From ManualsPrinter.com Manuals 
						

							5-10Troubleshooting
General considerations for clearing jams
Bear in mind the following considerations when attempting paper jam 
removal:
•If paper jams occur frequently, try using a different type of paper, 
replace the paper with paper from  another ream, or flip the paper 
stack over. The printer may have problems if paper jams recur after 
the paper is replaced.
• Whether or not the jammed pages are reproduced normally after 
printing is resumed, depends on the location of the paper jam.
MP Tray
1
Remove the paper jammed at the  MP tray.
2Reload the  MP tray. Open and close the top cover  to clear the error 
and the printer warms up and resumes printing.
CAUTION   When pulling the paper, pull it gently so as not 
to tear it. Torn pieces of pa per are difficult to remove and 
may be easily overlooked, deterring the paper jam recovery.
IMPORTANT Do not try to remove paper that has already been 
partially fed. Proceed to  Inside the Printer on page5-13.
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting5-11
Paper Cassette/Paper Feeder
1
Pull out the cassette or optional  paper feeder .
2Remove any partially fed paper. 
3Push the cassette  back in securely. The printer warms up and 
resumes printing.
IMPORTANT Do not try to remove paper that has already been 
partially fed. Proceed to  Inside the Printer on page5-13.
Note Check to see if paper is loaded correctly. If not, reload 
the paper.
Downloaded From ManualsPrinter.com Manuals 
						

							5-12Troubleshooting
Duplexer
Paper is jammed in the duplex section. Remove the jammed paper using 
the procedure given below.
1Pull the  paper cassette  all the way out of the printer.
2Open the duplexers cover  in front of the printer and remove any 
jammed paper.
Open the  duplexers cover  at the rear of the printer and remove any 
jammed paper.
3Push the  cassette back in securely, and open and close the  top 
cover  to clear the error. The printer warms up and resumes printing.
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting5-13
Inside the Printer
1
Pull the paper cassette  all the way out of the printer. Remove any 
partially fed paper..
2Open the  top cover and front cover , and lift the  process unit  together 
with the  toner container  out of the printer.
3Remove the drum unit from the printer by holding the green levers 
with both hands.
4If the jammed paper appears to be pinched by rollers, pull it along 
the normal running direction of the paper.
IMPORTANT Do not try to remove paper that has already been 
partially fed. Proceed to step 2.
CAUTION   The fuser unit inside the  printer is hot. Do not 
touch it, as it may re sult in burn injury.
NoteThe drum is sensitive to light. Never expose the process 
unit to light for more than five minutes.
Downloaded From ManualsPrinter.com Manuals 
						

							5-14Troubleshooting
5Return the drum unit to its position, aligning the guides at both ends 
with the slots in the printer.
6Insert the  process unit  together with the  toner container, back into 
the machine. Close the  top cover and the front cover . The printer 
warms up and resumes printing.
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting5-15
Rear Cover
1
Open the rear cover  and remove the jammed paper by pulling it out.
If the paper is  jammed inside the  fuser unit, open the  fuser cover 
and remove the paper by pulling it out.
2Close the rear cover , and open and close the top cover  to clear the 
error. The printer warms up and resumes printing.
CAUTION   The fuser unit inside the  printer is hot. Do not 
touch it, as it may re sult in burn injury.
Downloaded From ManualsPrinter.com Manuals 
						

							5-16Troubleshooting
Downloaded From ManualsPrinter.com Manuals 
						

							Option6-1
6Option
This chapter explains the options for this printer.
General Information 6-2
Expansion Memory Modules 6-3
Paper Feeder (PF-100 ) 6-6
Network Interface Card (IB-23) 6-7
CompactFlash (CF) Card 6-8
Downloaded From ManualsPrinter.com Manuals 
						

							6-2Option
General Information
The printers have the following options available to satisfy your printing 
requirements. 
For instructions on installing individual options, refer to the 
documentation included with the option. Some options are explained in 
the following sections.
NoteInstall the memory module before installing the optional 
paper feeder  (PF-100).
Expansion Memory 
Module (DIMM 
64/128/256/512 MB)
Paper Feeder (PF-100) CF Card
Network Interface 
Card (IB-23)
Downloaded From ManualsPrinter.com Manuals