Kyocera FS 1100 User Manual

							Loading Paper2-13
6Insert the paper cassette into the slot in the printer. Push it straight in 
as far as it will go.
There is a  paper gauge  on the left side of the front of the paper 
cassette to indicate the remaining paper supply. When paper is 
exhausted, the pointer will go down to the level of (empty).
7Specify the paper size and type for the cassette using  Configuration 
Tool . For more information, refer to  Configuration Tool on page3-14.
Note Do not load paper above the triangle mark located on 
the width guide.
Downloaded From ManualsPrinter.com Manuals 
						

							2-14Loading Paper
Loading Paper into MP (Multi-Purpose)Tray
FS-1300D can load 50 sheets of 11 × 8 1/2 or A4 paper (80 g/m²)  into 
the MP Tray. On the other hand, FS-1100 can one sheet  into the  Manual 
Feed .
1Pull the  MP tray towards you until it stops..
2Adjust the position of the paper guides  on the MP tray . Standard 
paper sizes are marked on the  MP tray or Manual Feed . For 
standard paper sizes, slide the paper guides to the corresponding 
mark.
3Pull out the subtray  (for FS-1300D only).
FS-1300D
FS-1100
IMPORTANT
When pulling the cassette ou t of the printer, ensure 
it is supported and does not fall out.
FS-1300D FS-1100
Downloaded From ManualsPrinter.com Manuals 
						

							Loading Paper2-15
4Align the paper with the paper guides and insert as far as it will go.
FS-1300D
FS-1100
Note
Do not load more paper than exceeds the tab of the  MP 
tray  (for FS-1300D only).
Note If the paper is considerably curled in one direction, for 
example, if the paper is already printed on one side, try to roll 
the paper in the opposite direction to counteract the curl. 
Printed sheets will then come out flat (for FS-1300D only).
Correct
Incorrect
Downloaded From ManualsPrinter.com Manuals 
						

							2-16Loading Paper
When loading envelope, place with the envelope flap closed and 
keep the printing side face-up. Insert envelope against the guide 
with the flap on the front or left side until they stop.
5Specify the paper size and type for MP tray using Configuration Tool. 
For more information, refer to  Configuration Tool on page3-14.
Correct
Correct
Incorrect
Downloaded From ManualsPrinter.com Manuals 
						

							Connecting and Printing3-1
3 Connecting and Printing
This chapter explains how to start up the printer, print from your PC, and 
use the application software included in the CD-ROM.
Connections3-2
Installing the Printer Driver 3-3
Printing 3-7
Status Monitor 3-10
Configuration Tool 3-14
Uninstalling Software 3-18
Downloaded From ManualsPrinter.com Manuals 
						

							3-2Connecting and Printing
Connections
This section explains how to start up the printer.
Connecting the USB Cable
Follow the steps as below for connecting the USB cable.
1Connect the USB cable  (not included) to the USB Interface 
Connector .
2Connect the other end of the USB cable  to the computers USB 
interface connector .
Connecting the Power Cord
Install the printer close to an  AC wall outlet. If an extension cord is used, the 
total length of the power cord plus ex tension should be 5 meters (16 feet) or 
less.
1Connect the power cord  to the Power Cord Connector  at the rear of 
the printer.
2Connect the other end of the power cord  to a power outlet.
3Press the Power Switch to On ( | ). The printer begins to warm up.
NoteUse a  USB cable  with a rectangular Type A plug and a 
square Type B plug. The USB cable should be shielded and 
no longer than 5 meters (16 feet) long. 
Note Ensure the printers power switch is off. Only use the power 
cord supplied with the printer. 
IMPORTANT If you install the  toner container and switch on the 
power, after a moment the indicators light in anticlockwise 
direction. When the printer is first switched on after toner 
installation, there will be a dela y of approximately 15 minutes 
before the printer gets ready to print. Once the  [Ready] indicator 
lights, printer insta llation is complete.
Downloaded From ManualsPrinter.com Manuals 
						

							Connecting and Printing3-3
Installing the Printer Driver
According to the instructions of the Installation Guide, connect the PC to 
the printer and turn on them to install the printer driver. 
For more 
information on printer driver, refer to the  KX Driver User Guide.
Installing the Printer Driver on Windows PC
This section explains how to install the printer driver in Windows Vista.
1Ensure the printer is plugged in and connected to the computers 
USB or Network port  before installing software from the CD-ROM.
2Insert the CD-ROM (Product Library) into the CD-ROM drive. If 
AutoPlay screen appears, click  Run Setup.exe. The Notice  screen 
appears.
3Select  View License Agreement  to read the information and select 
Accept  to proceed.
4Click Install Software . Installation Method  screen appears.
5Select Express Mode or Custom Mode as the installation method.
• Express Mode: If the printer is connected via USB or a network and 
is turned on, the installer detects the printer. Select Express Mode to 
perform a standard installation.
• Custom Mode: This option allows you to select items to be installed 
as required and to specify the port.
Proceed the section below according to the installation method.
Note To install the printer driver, you must log on with 
administrator priviledge.
Note If Found New Hardware window appears, click 
Cancel. 
Note If the installation program fails to launch, use Windows 
Explorer to access the CD-ROM and select Setup.exe. 
Note In Windows XP, click  Install Software to start the 
Installation  wizard. Click  Next to display the  Installation 
Method  screen.
Downloaded From ManualsPrinter.com Manuals 
						

							3-4Connecting and Printing
Express Mode
When selecting Express Mode, printer driver and fonts are installed. 
After installting with this mode, the other utilities can be added using 
Custom Mode .
1On Installation Method screen, click  Express Mode. The installer 
searches the connected printers on  Discover Printing System  
screen. If no printer is discoverd, ensure the printer is plugged in and 
connected to the computers  USB or Network port , then cleck 
Refresh  to search printers again.
2Select the printer you want to install, and click  Next.
3Confirm the settings and click  Install. Printer driver installation 
starts.
4Installation Completed  screen appears. Click Finish to retur n to the 
main menu. 
Note If Found New Hardware  window appears, click Cancel.
NoteIf the Windows Security  screen appears, click Install 
this driver software anyway  to proceed installation. If the 
Hardware Installation  screen appears in Windows XP, click 
Continue Anyway.
Downloaded From ManualsPrinter.com Manuals 
						

							Connecting and Printing3-5
Custom Mode
When selecting Custom Mode, printer port and utilities are changed 
as necessary.
1On Installation Method  screen, click Custom Mode .
2On Driver  tab and  Utility tab of the  Custom Installation  screen, select 
the printer driver and utilities you want to install, and click  Next.
3On Printer Port screen, select the printer port connected to the 
printer, click  Next. 
4Confirm the settings and click  Install. Printer driver installation 
starts.
5Installation Completed  screen appears. Click  Finish to return to the 
main menu.  
NoteClick Add Port  to add new port as necessary.
NoteIf the Windows Security screen appears, click  Install 
this driver software anyway  to proceed installation. If the 
Hardware Installation  screen appears in Windows XP, click 
Continue Anyway .
Downloaded From ManualsPrinter.com Manuals 
						

							3-6Connecting and Printing
Installing the Printer Driver on Mac OS
This section explains how to install the printer driver in Mac OS.
1Ensure the printer is connected to the computers  USB or Network 
port  before installing software from the CD-ROM.
2Insert the CD-ROM (Product Library) into the CD-ROM drive.
3Double-click the CD-ROM icon.
4Double-click  OS X 10.2 and 10.3 Only  or OS X 10.4  according to 
OS version you use.
5Double-click  Kyocera OS X x.x  or Kyocera OS X 10.4 x.x . Printer 
driver installation starts.
6Install the printer driver according to the instructions of Installer.
Downloaded From ManualsPrinter.com Manuals