Kyocera FS 1028MFP User Manual

Preparation before Use 
OPERATION GUIDE2-5
2
Connecting Cables 
Follow the steps below to connect cables to the machine.
1Turn the main power switch off (O).
2Connect the machine to the PC or your network 
device. When using the network interface, remove 
the cap..
3Connect one end of the supplied power cable to the 
machine and the other end to a power outlet.
IMPORTANT: Only use the power cable that comes with the machine.
Downloaded From ManualsPrinter.com Manuals 

Preparation before Use 
2-6OPERATION GUIDE
4Turn the main power switch on (|). The machine 
begins to warm up.
5When connecting the network cable, configure the 
network. For details, refer to  Network Setup (LAN 
Cable Connection) on page 2-12 .
Downloaded From ManualsPrinter.com Manuals 

Preparation before Use 
OPERATION GUIDE2-7
2
Switching the Language for Display [Language] 
Select the language displayed on the Message Display.
Use the procedure below to select the language.
1Press the System Menu/Counter  key on the main 
unit operation panel.
When you are performing user management and 
have not logged in, a login screen will appear. 
Then, enter the user ID and password to log in.
NOTE: 
• Refer to Character Entry Method on Appendix-5  for 
details on entering characters.
• If...

Preparation before Use 
2-8OPERATION GUIDE
Completed.
 is displayed and the screen returns to 
the Common Settings menu.
Downloaded From ManualsPrinter.com Manuals 

Preparation before Use 
OPERATION GUIDE2-9
2
Setting Date and Time
Follow the steps below to set the local date and time at the place of installation.
When you send an E-mail using the tr ansmission function, the date and time  as set here will be printed in the 
header of the E-mail message. Set the date, time and time  difference from GMT of the region where the machine 
is used.
NOTE: Be sure to set the time difference  before setting the date and time.
1Turn on the main power switch.
2Press the...

Preparation before Use 
2-10OPERATION GUIDE
5Press the U or  V key to select [Date Setting].
6A login screen will appear. Then, enter the user ID 
and password to log in.
7Press the  OK key. The Date Setting menu appears.
8Press the  U or  V key to select [Time Zone].
9Press the  OK key. Time Zone appears.
10Press the  U or  V key to select your region and 
then press the  OK key.
Completed.  is displayed and the screen returns to 
the Date Setting menu.
11Press the  U or  V key to select [Summer Time]....

Preparation before Use 
OPERATION GUIDE2-11
2
Completed. is displayed and the screen returns to 
the Date Setting menu.
14Press the  U or  V key to select [Date/Time].
15Press the  OK key. Date/Time appears.
16Press the  Y or  Z key to move the cursor position, 
press the  U or  V key to enter year, month and day, 
and then press the  OK key.
17Press the  Y or  Z key to move the cursor position, 
press the  U or  V key to enter hours, minutes and 
seconds, and then press the  OK key.
Completed.  is...

Preparation before Use 
2-12OPERATION GUIDE
Network Setup (LAN Cable Connection)
The machine is equipped with network interface, which is compatible with network protocols such as TCP/IP 
(IPv4), TCP/IP (IPv6), IPX/ SPX, NetBEUI, IPSec, and AppleTalk. It enables network printing on the Windows, 
Macintosh, UNIX, NetWare and other platforms.
This section explains the  TCP/IP (IPv4) Setup and AppleTalk Setup  procedures. For other network settings, 
refer to  Network Setup on page 8-128 .
• TCP/IP (IPv4)...

Preparation before Use 
OPERATION GUIDE2-13
2
IMPORTANT: To make the settin gs, you must have 
logged in using a user ID  with administrator privileges.
The default settings of the login user name and login 
password are both  2800.
If you have logged in using a user ID without 
administrator privileges,  the screen will display 
Administrator only. and return to the standby screen.
3In the System menu, press the U  or V key to select 
[Network Setting].
4Press the  OK key. The Network Setting menu...

Preparation before Use 
2-14OPERATION GUIDE
9Press the U or V  key to select [On] and then press 
the  OK key.
Completed.  is displayed and the screen returns to 
the TCP/IP Settings menu.
10Press the  U or  V key to select [IPv4 Setting].
11Press the  OK key. The IPv4 Setting menu appears.
12Press the  U or  V key to select [DHCP].
13Press the  OK key. DHCP appears.
14Press the  U or V  key to select [O ff] and then press 
the  OK key. 
Completed.  is displayed and the screen returns to 
the IPv4...