Konica Minolta magicolor 4750DN User Manual

							Hard Disk Kit HD-P03 10-8
2Using a screwdriver, remove two 
screws. 
3Slide the panel slightly to the 
down and lift it off the printer.
4Attach the two cables to the hard 
disk kit.
Downloaded From ManualsPrinter.com Manuals 
						

							Hard Disk Kit HD-P0310-9
5Insert the hard disk kit mounting 
pins.
6Plug the two cables on the hard 
disk kit into the connector.
7Reinstall the panel and tighten two screws.
8Reconnect all interface cables.
9Reconnect the power cord, and 
turn on the printer.
10Declare the Hard Disk in the Windows printer driver (Properties/Configure 
tab).
Downloaded From ManualsPrinter.com Manuals 
						

							CompactFlash 10-10
CompactFlash
If you install a CompactFlash card, the followings can be performed:
–Collate printing
–Fonts forms download
–User Authentication/Account Track
–Direct printing (including the use of PageScope Direct Print)
–XPS printing
Only CompactFlash cards with a capacity of 1 GB, 2 GB, 4 GB or 8 
GB can be used.
The job printing/saving function is not available with a CompactFlash 
card. These functions require that an optional hard disk kit HD-P03 be 
installed.
A hard disk kit HD-P03 and a CF Adapter MK-725 cannot be installed 
simultaneously.
Installing the CF Adapter MK-725 and CompactFlash 
card
Note
If the installed CompactFlash card is used with a device other than this 
printer, such as a computer or digital camera, the card is automatically 
formatted and all of its data is deleted.
Note
It is very important to protect the printer controller board and any 
associated circuit boards from electrostatic damage. Before performing 
this procedure, review the antistatic caution on page 10-3. In addition, 
always handle circuit boards by their edges only.
Downloaded From ManualsPrinter.com Manuals 
						

							CompactFlash10-11
1Turn off the printer and discon-
nect the power cord and inter-
face cables.
2Using a screwdriver, remove two 
screws. 
3Slide the panel slightly to the 
down and lift it off the printer.
Downloaded From ManualsPrinter.com Manuals 
						

							CompactFlash 10-12
4Attach the two cables to the CF 
adapter.
5Fully insert the CompactFlash 
card into the appropriate slot.
When the CompactFlash card is 
correctly inserted, the button on 
the top side of the slot (circled in 
the illustration) slightly pops out.
Before removing the 
CompactFlash card, 
press in this button.
Downloaded From ManualsPrinter.com Manuals 
						

							CompactFlash10-13
6Insert the CF adapter mounting 
pins.
7Plug the two cables on the CF 
disk kit into the connector.
8Reinstall the panel and tighten two screws.
9Reconnect all interface cables.
10Reconnect the power cord, and 
turn on the printer.
11Declare the Memory card in the Windows printer driver (Properties/Con-
figure tab).
Downloaded From ManualsPrinter.com Manuals 
						

							Lower Feeder Unit PF-P07 10-14
Lower Feeder Unit PF-P07
You can install up to one optional lower feeder unit PF-P07 (Tray 3). The 
lower feeder unit PF-P07 increases your printer’s media feed capacity by 500 
sheets. 
Kit Contents
„Lower feeder unit with a tray (500-sheet capacity)
Downloaded From ManualsPrinter.com Manuals 
						

							Lower Feeder Unit PF-P0710-15 Installing a Lower Feeder Unit PF-P07 
Note
Since consumables are installed in the printer, be sure to keep the 
printer level when moving it in order to prevent accidental spills.
1Turn off the printer and discon-
nect the power cord and inter-
face cables.
2Prepare the lower feeder unit.
Be sure to place the lower feeder unit on a level surface.
3Open the right side cover of the 
lower feeder unit.
The right side cover of the lower feeder must be opened before the 
feeder can be installed onto the printer.
Downloaded From ManualsPrinter.com Manuals 
						

							Lower Feeder Unit PF-P07 10-16
4With another person’s help, 
place the printer on top of the 
lower feeder unit, making sure 
that the positioning pins on the 
lower feeder unit correctly fit into 
the holes on the bottom of the 
printer.
WARNING!
This printer weighs approximately 27 kg (60 lbs) when it is fully loaded 
with consumables. The printer must be lifted by two people.
5Close the right side cover of the 
lower feeder unit.
6Reconnect all interface cables.
27 kg
60 lbs
Downloaded From ManualsPrinter.com Manuals 
						

							Lower Feeder Unit PF-P0710-17
7Reconnect the power cord, and 
turn on the printer.
8Declare Paper Source Unit 3 in the Windows printer driver (Properties/
Configure tab).
Downloaded From ManualsPrinter.com Manuals