Konica Minolta magicolor 4750DN User Manual

							Cleaning the Printer 8-8
Cleaning the Media Transfer Rollers for Tray 3
1Open the right side cover of 
Tray 3.
Before opening the right 
side cover of Tray 3, fold 
up Tray 1.
2Clean the media transfer rollers 
by wiping them with a soft, dry 
cloth.
3Close the right side cover of 
Tray 3.
Downloaded From ManualsPrinter.com Manuals 
						

							Cleaning the Printer8-9 Cleaning the Laser Lens
This printer is constructed with four laser lenses. Clean all lenses as 
described below. The laser lens cleaning tool should be attached to the inside 
of the tray 2.
1Pull out the tray 2.
2Remove the cover.
Since the cover will be used 
later, do not return it to its 
original position.
3Remove the cleaning tool from 
the tray 2. 
Downloaded From ManualsPrinter.com Manuals 
						

							Cleaning the Printer 8-10
4Close the tray 2.
5Open the printer’s front cover.
6Remove the waste toner bottle 
and the toner cartridge and 
imaging unit for the color of laser 
lens to be cleaned.
For details on removing the 
toner cartridge, imaging unit 
or waste toner bottle, refer to 
“Replacing a Toner Car-
tridge” on page 7-7 or 
“Replacing a Imaging Unit” 
on page 7-12.
Do not tilt removed toner car-
tridge, otherwise toner may 
spill.
Do not tilt removed waste toner box, otherwise waste toner may spill.
Downloaded From ManualsPrinter.com Manuals 
						

							Cleaning the Printer8-11
7Attach the cover to the removed 
imaging unit.
8Insert the laser lens cleaning 
tool into the imaging unit open-
ing, pull it out, and then repeat 
this back and forth movement 2 
or 3 times.
9Install the removed toner car-
tridge, imaging unit and waste 
toner bottle.
For details on installing the 
toner cartridge, imaging unit 
or waste toner bottle, refer to 
“Replacing a Toner Car-
tridge” on page 7-7 or 
“Replacing a Imaging Unit” 
on page 7-12.
Downloaded From ManualsPrinter.com Manuals 
						

							Cleaning the Printer 8-12
10Close the front cover.
When closing the front 
cover, press the area of 
the cover with small pro-
jections.
11Pull out the tray 2.
12Return the laser lens cleaning 
tool to its holder on the inside of 
the tray 2.
Downloaded From ManualsPrinter.com Manuals 
						

							Cleaning the Printer8-13
13Close the cover.
14Close the tray 2.
15Clean between each of the laser lenses in the same way.
The laser lens cleaning tool is included with the printer.
Safely store the laser lens cleaning tool so that it will not be lost.
Downloaded From ManualsPrinter.com Manuals 
						

							Cleaning the Printer 8-14
Downloaded From ManualsPrinter.com Manuals 
						

							Troubleshooting
Downloaded From ManualsPrinter.com Manuals 
						

							Introduction 9-2
Introduction
This chapter provides information to aid you in resolving printer problems you 
may encounter, or at least guide you to the proper sources for help. 
Printing a Configuration Page
Print a configuration page to verify the printer is printing correctly, or to check 
the printer configuration.Printing the Configuration Page page 9-2
Preventing Media Misfeeds page 9-3
Understanding the Media Path page 9-4
Clearing Media Misfeeds page 9-5
Solving Problems with Media Misfeeds page 9-23
Solving Other Problems page 9-25
Solving Problems with Printing Quality page 9-30
Status, Error, and Service Messages page 9-36
Press Key 
(once)Until Display Reads
READY
PRINT MENU
If an optional hard disk kit HD-P03 is installed, the PROOF/
PRINT MENU appears at the top of the menu. Press the   
key to select the PRINT MENU.
CONFIGRATION PG
PRINT
The configuration page prints and the printer goes back
to READY.
Downloaded From ManualsPrinter.com Manuals 
						

							Preventing Media Misfeeds9-3
Preventing Media Misfeeds
Make sure that...
Media matches the printer specifications.
Media is flat, especially on the leading edge.
The printer is on a hard, flat, level surface.
You store media in a dry location away from moisture and humidity.
You always adjust the media guides in the tray after inserting the media (a 
guide that is not properly adjusted can cause poor print quality, media mis-
feeds, and printer damage).
You load the media printing-side up in the tray (many manufacturers place an 
arrow on the end of the wrapper to indicate the printing side).
Avoid...
Media that is folded, wrinkled, or excessively curled.
Double feeding (remove the media and fan the sheets—they may be sticking 
together). 
Loading more than one type/size/weight of media in a tray at the same time.
Overfilling the trays. 
Allowing the output tray to overfill (the output tray has a 200-sheet capacity—
misfeeding may occur if you allow more than 200 sheets of media to accumu-
late at one time).
Downloaded From ManualsPrinter.com Manuals