Konica Minolta magicolor 4650EN User Manual

CompactFlash 227
CompactFlash
If you install a CompactFlash card, the followings can be performed:
–Collate printing
–Fonts forms download
–User Authentication/Account Track
–Direct printing (including the use of PageScope Direct Print)
Only CompactFlash cards with a capacity of 256 MB, 512 MB, 1 GB, 2 
GB or 4 GB can be used.
The job printing/saving function is not available with a CompactFlash 
card. These functions require that an optional hard disk kit be 
installed.
A hard disk kit and a CF...

CompactFlash 228
1Turn off the printer and discon-
nect the power cord and inter-
face cables.
2Using a screwdriver, remove the 
screw. Then, slide the rear cover 
to the right and remove it.
3Using a screwdriver, loosen the 
seven screws. (Do not remove 
them from the printer.)
Downloaded From ManualsPrinter.com Manuals 

CompactFlash 229
4Slide the panel slightly to the 
right and lift it off the printer.
5Plug the cable on the CF 
adapter into the connector on 
the controller board.
6Insert the three mounting pins 
on the CF adapter into the holes 
in the controller board to mount 
the CF adapter onto the control-
ler board.
Downloaded From ManualsPrinter.com Manuals 

CompactFlash 230
7Fully insert the CompactFlash 
card into the appropriate slot.
When the CompactFlash card is 
correctly inserted, the button on 
the top side of the slot (circled in 
the illustration) slightly pops out.
Before removing the 
CompactFlash card, 
press in this button.
8Reinstall the panel and tighten the seven screws.
9Attach the rear cover.
10Reconnect all interface cables.
11Reconnect the power cord, and 
turn on the printer.
12Declare the Memory card in the Windows printer driver...

Lower Feeder Unit 231
Lower Feeder Unit
You can install up to one optional lower feeder unit (Tray 3). The lower feeder 
unit increases your printer’s media feed capacity by 500 sheets. 
Kit Contents
„Lower feeder unit with a tray (500-sheet capacity)
Downloaded From ManualsPrinter.com Manuals 

Lower Feeder Unit 232
Installing a Lower Feeder Unit 
Note
Since consumables are installed in the printer, be sure to keep the 
printer level when moving it in order to prevent accidental spills.
1Turn off the printer and discon-
nect the power cord and inter-
face cables.
2Prepare the lower feeder unit.
Be sure to place the lower feeder unit on a level surface.
3Open the right side cover of the 
lower feeder unit.
The right side cover of the lower feeder must be opened before the 
feeder can be...

Lower Feeder Unit 233
4With another person’s help, 
place the printer on top of the 
lower feeder unit, making sure 
that the positioning pins on the 
lower feeder unit correctly fit into 
the holes on the bottom of the 
printer.
WARNING!
This printer weighs approximately 37kg (81.5lb) when it is fully loaded 
with consumables. The printer must be lifted by two people.
5Close the right side cover of the 
lower feeder unit.
6Reconnect all interface cables.
37 kg37 kg81.5 lbs81.5 lbs
Downloaded From...

Lower Feeder Unit 234
7Reconnect the power cord, and 
turn on the printer.
8Declare Paper Source Unit 3 in the Windows printer driver (Properties/
Configure tab).
Downloaded From ManualsPrinter.com Manuals 

Appendix
Downloaded From ManualsPrinter.com Manuals 

Safety Specifications 236
Safety Specifications
Technical Specifications
Printer
Printer
Safety standards U.S. model UL 60950-1 (2003)
European model EN 60950-1 (2001)+All
China model GB 4943-2001
Taiwan CNS14336 (2004)
Korea K 60950
Others IEC-60950-1 (2001)+Country’s Differ-
ences in CB Bulletin
EMC standards U.S. model 21CFR Chapterl subchapterJ 
part1040 (Laser Notice No.50)
European model EN 60825-1 
(1994)+A2(2001)+A1(2002)
China model GB 7247.1 (2001)
Other IEC 60825-1 (1993)+A1 (1997)+A2 
(2001)...