Konica Minolta magicolor 4650EN User Manual

11
Installing
Accessories
Downloaded From ManualsPrinter.com Manuals 

Introduction 218
Introduction
Note
Use of accessories not manufactured or supported by 
KONICA MINOLTA will void your warranty.
This chapter provides information about the following accessories.
Note
The hard disk kit and CF adapter cannot be installed to be used at the 
same time. 
Installing accessories always requires that the printer and accessories 
are turned off and unplugged during installation.Dual In-Line 
Memory Module 
(DIMM)256 MB, 512 MB DIMM 
(DDR2-667 SO-DIMM, 166 MHz, 200pins, No ECC,...

Antistatic Protection 219
Antistatic Protection
Note
It’s very important to protect the printer controller board from 
electrostatic damage while performing any task involving the controller 
board.
Turn off all power switches first. If an antistatic wrist strap is provided in 
your printer option kit, attach one end of it to your wrist and the other 
end to the bare metal chassis on the back of your printer. Never attach 
the wrist strap to any piece of equipment with an electrical current 
present....

Dual In-Line Memory Module (DIMM) 220
Dual In-Line Memory Module (DIMM)
You may need additional memory (DIMM) for complex graphics and 
for duplex (double-sided) printing. 
Dual in-line memory module (or DIMM) is compact circuit board with sur-
face-mount memory chips.
There is 256 MB of onboard memory and one available memory expansion 
slot. the memory can be expanded to a maximum of 768 MB (256 MB + 512 
MB).
Installing a DIMM
Note
It’s very important to protect the printer controller board and any...

Dual In-Line Memory Module (DIMM) 221
3Using a screwdriver, loosen the 
seven screws. (Do not remove 
them from the printer.)
4Slide the panel slightly to the 
right and lift it off the printer.
5Insert the new DIMM straight 
into the DIMM connector until 
the latches snap into the locked 
position.
Observe the keyed side of the 
DIMM to align it with the connec-
tor. If you cannot snap the DIMM 
into place, do not force it. Repo-
sition it, making sure that the 
DIMM is seated completely in 
the...

Dual In-Line Memory Module (DIMM) 222
9Reconnect the power cord, and 
turn on the printer.
10Declare the additional Printer Memory in the Windows printer driver 
(Properties/Configure tab).
11Print a configuration page (PRINT MENU/CONFIGURATION PG) and 
verify that the total amount of the RAM installed in your printer is listed.
Downloaded From ManualsPrinter.com Manuals 

Hard Disk Kit 223
Hard Disk Kit
If you install a hard disk kit, the followings can be performed:
–Collate printing
–Job printing/saving
–Fonts/forms download
–User  Authentication/Account Track
–Direct printing
A hard disk kit and a CF adapter cannot be installed simultaneously.
Installing the Hard Disk kit
Note
It’s very important to protect the printer controller board and any 
associated circuit boards from electrostatic damage. Before performing 
this procedure, review the antistatic caution on page...

Hard Disk Kit 224
2Using a screwdriver, remove the 
screw. Then, slide the rear cover 
to the right and remove it.
3Using a screwdriver, loosen the 
seven screws. (Do not remove 
them from the printer.)
4Slide the panel slightly to the 
right and lift it off the printer.
Downloaded From ManualsPrinter.com Manuals 

Hard Disk Kit 225
5Plug the cable on the hard disk 
kit into the connector on the con-
troller board.
6Insert the three mounting pins 
on the hard disk kit into the holes 
in the controller board to mount 
the hard disk kit onto the control-
ler board.
7Reinstall the panel and tighten the seven screws.
8Attach the rear cover.
9Reconnect all interface cables.
Downloaded From ManualsPrinter.com Manuals 

Hard Disk Kit 226
10Reconnect the power cord, and 
turn on the printer.
11Declare the Hard Disk in the Windows printer driver (Properties/Configure 
tab).
Downloaded From ManualsPrinter.com Manuals