Konica Minolta magicolor 4650EN User Manual

Replacing
Consumables
Downloaded From ManualsPrinter.com Manuals 

Replacing Consumables 128
Replacing Consumables
Note
Failure to follow instructions as outlined in this manual could result in 
voiding your warranty.
Note
If an error message (TONER OUT, TRANS.BELT END OF LIFE, etc.) 
appears, print out the configuration page, and then check the status of the 
other consumables. For details on the error messages, refer to “Error 
Messages (Warning:)” on page 207. For details on printing the 
configuration page, refer to “Printing a Configuration Page” on page 172.
About...

Replacing Consumables 129
Note
Do not use refilled toner cartridges or unapproved toner cartridges. Any 
damage to the printer or quality problems caused by a refilled toner 
cartridge or an unapproved toner cartridge will void your warranty. No 
technical support is provided to recover from these problems.
When replacing a toner cartridge, refer to the following table. For optimum 
print quality and performance, use only approved KONICA MINOLTA toner 
cartridges for your specific printer type, as listed...

Replacing Consumables 130
For optimum print quality and performance, use only the corre-
sponded TYPE genuine KONICA MINOLTA toner cartridges.
Keep toner cartridges: 
„In their packaging until you’re ready to install them.
„In a cool, dry location away from sunlight (due to heat). 
The maximum storage temperature is 35°C (95°F) and the maximum 
storage humidity is 85% (noncondensing). If the toner cartridge is moved 
from a cold place to a warm, humid place, condensation may occur, 
degrading print...

Replacing Consumables 131 Replacing a Toner Cartridge
Note
Be careful not to spill toner while replacing a toner cartridge. If toner 
spills, immediately wipe it off with a soft, dry cloth.
If 
TONER LOW on the SYS DEFAULT MENU/ENABLE WARNING is set 
to 
ON, the message TONER LOW X (where “X”. represents the color of the 
toner) appears when toner cartridge becomes near empty. Follow the steps 
below to replace the toner cartridge.
If TONER LOW on the SYS DEFAULT MENU/ENABLE WARNING 
is set to 
OFF, you...

Replacing Consumables 132
3Lower the lever to release the 
lock.
4Grab the handle of the toner car-
tridge to be replaced, and then 
pull out the cartridge. 
The following instructions show 
the procedure to replace the 
toner cartridge(Y).
Note
Dispose of the used toner cartridge according to your local regulations. 
Do not burn the toner cartridge.
For details, refer to “About Toner Cartridges” on page 128.
5Check the color of the new toner cartridge to be installed.
6Remove the toner cartridge from...

Replacing Consumables 133
7Shake the cartridge to distribute 
the toner.
8Make sure that the toner car-
tridge is the same color as the 
printer compartment, and then 
insert the toner cartridge into the 
printer.
9Make sure that the toner car-
tridge is securely installed, and 
then peel off the protective film.
Y
3 ×
YY
Y
Y
Downloaded From ManualsPrinter.com Manuals 

Replacing Consumables 134
10Raise the front lever to its origi-
nal position.
11Pull the lever to the left to lock it 
in place.
The front lever should be 
securely returned to its 
original position; other-
wise, the front cover of 
the printer cannot be 
closed.
12Close the front cover.
Y
Y
Y
Downloaded From ManualsPrinter.com Manuals 

Replacing Consumables 135 Replacing a Imaging Unit
When replacing a imaging unit, refer to the following table. For optimum print 
quality and performance, use only approved KONICA MINOLTA imaging units 
for your specific printer type, as listed in the table below. You can find your 
printer type and the imaging unit part numbers on the consumables reorder 
label inside the front cover your printer.
Note
Do not touch the OPC drum 
surface. This could lower image 
quality.
Printer 
Ty p ePrinter Parts...

Replacing Consumables 136
If I-UNIT LOW on the SYS DEFAULT MENU/ENABLE WARNING is set 
to 
ON, the message I-UNIT LOW X (where “X”. represents the color of the 
toner) appears when a imaging unit becomes near empty. Follow the steps 
below to replace the imaging unit.
You are advised to replace the indicated imaging unit when the mes-
sage 
I-UNIT LIFE X appears.
1Check the message window to see which color imaging unit needs replac-
ing.
2Open the printer’s front cover.
3Pull the front lever of the...