Konica Minolta bizhub C35P User Manual

Hard Disk Kit HD-P03 10-10
11Reconnect the power cord, and 
turn on the printer.
12Declare the Hard Disk in the Windows printer driver (Properties/Configure 
tab).
Downloaded From ManualsPrinter.com Manuals 

CompactFlash10-11
CompactFlash
If you install a CompactFlash card, the followings can be performed:
–Collate printing
–Fonts forms download
–User Authentication/Account Track
–Direct printing (including the use of PageScope Direct Print)
–XPS printing
Only CompactFlash cards with a capacity of 1 GB, 2 GB, 4 GB or 8 
GB can be used.
The job printing/saving function is not available with a CompactFlash 
card. These functions require that an optional hard disk kit HD-P03 be 
installed.
A hard disk kit...

CompactFlash 10-12
1Turn off the printer and discon-
nect the power cord and inter-
face cables.
2Using a screwdriver, remove the 
back cover.
3Using a screwdriver, remove two 
screws. 
Downloaded From ManualsPrinter.com Manuals 

CompactFlash10-13
4Slide the panel slightly to the 
down and lift it off the printer.
5Attach the two cables to the CF 
adapter.
Downloaded From ManualsPrinter.com Manuals 

CompactFlash 10-14
6Fully insert the CompactFlash 
card into the appropriate slot.
When the CompactFlash card is 
correctly inserted, the button on 
the top side of the slot (circled in 
the illustration) slightly pops out.
Before removing the 
CompactFlash card, 
press in this button.
7Insert the CF adapter mounting 
pins.
Downloaded From ManualsPrinter.com Manuals 

CompactFlash10-15
8Plug the two cables on the CF 
disk kit into the connector.
9Reinstall the panel and tighten two screws.
10Attach the back cover and tighten four screws.
11Reconnect all interface cables.
12Reconnect the power cord, and 
turn on the printer.
13Declare the Memory card in the Windows printer driver (Properties/Con-
figure tab).
Downloaded From ManualsPrinter.com Manuals 

Lower Feeder Unit PF-P09 10-16
Lower Feeder Unit PF-P09
You can install up to one optional lower feeder unit PF-P09 (Tray 3). The 
lower feeder unit PF-P09 increases your printer’s media feed capacity by 500 
sheets. 
Kit Contents
„Lower feeder unit with a tray (500-sheet capacity)
„Cover
Downloaded From ManualsPrinter.com Manuals 

Lower Feeder Unit PF-P0910-17 Installing a Lower Feeder Unit PF-P09 
Note
Since consumables are installed in the printer, be sure to keep the 
printer level when moving it in order to prevent accidental spills.
1Turn off the printer and discon-
nect the power cord and inter-
face cables.
2Prepare the lower feeder unit.
Be sure to place the lower feeder unit on a level surface.
3Attach the cover.
4Open the right side cover of the 
lower feeder unit.
The right side cover of the lower feeder must be...

Lower Feeder Unit PF-P09 10-18
5With another person’s help, 
place the printer on top of the 
lower feeder unit, making sure 
that the positioning pins on the 
lower feeder unit correctly fit into 
the holes on the bottom of the 
printer.
WARNING!
This printer weighs approximately 27 kg (60 lbs) when it is fully loaded 
with consumables. The printer must be lifted by two people.
6Close the right side cover of the 
lower feeder unit.
7Reconnect all interface cables.
27 kg
60 lbs
Downloaded From...

Lower Feeder Unit PF-P0910-19
8Reconnect the power cord, and 
turn on the printer.
9Declare Paper Source Unit 3 in the Windows printer driver (Properties/
Configure tab).
Downloaded From ManualsPrinter.com Manuals