Konica Minolta bizhub 211 User Manual

Making copies5
bizhub 163/211 5-41
10Press the [+] or [,] key until TRAY1 PAPER is selected, and then 
press the [OK] key.
11Press the [+] or [,] key until MEDIA TYPE is selected, and then press 
the [OK] key.
12Press the [+] or [,] key until CARD is selected, and then press the 
[OK] key.
13Press the [Back] key twice.
The main screen appears again.
PAPER SOURCE SETUP
TRAY1 PAPER
INCH/METRIC
PAPER TYPE
TRAY1 PAPER
MEDIA TYPE
PAPER SIZE
TRAY1 MEDIA TYPE
TRANSPARENCY
PLAIN
CARD
Downloaded From...

5Making copies
5-42 bizhub 163/211
14Press the [Paper] key, and then 
select the 1st paper drawer.
15If necessary, specify any other copy settings.
– Refer to Before making copies on page 4-3.
– Refer to Advanced copy operations on page 6-3.
16Press the [Start] key.
Downloaded From ManualsPrinter.com Manuals 

Making copies5
bizhub 163/211 5-43Copying onto non-standard-sized paper
As an example, the following procedure describes how to make copies onto 
non-standard-sized paper (250 mm e 180 mm) loaded into the manual 
bypass tray or the multi bypass tray.
2
Note 
When loading non-standard-sized documents and paper, be sure to first 
measure their sizes.
The document scales at the edges of the original glass are useful for 
measuring documents and paper.
1Position the document to be copied.
– Refer to Loading...

5Making copies
5-44 bizhub 163/211
2Adjust the paper guides in the bypass tray, and then load the paper into 
the tray.
– Load the paper so that the side to be printed on faces down.
– Load the paper into the manual bypass tray one sheet at a time.
– A maximum of 100 sheets of paper can be loaded into the multi 
bypass tray. Do not load so much paper into the multi bypass tray 
that the top of the stack is higher than the , mark.
The BYPASS PAPER SETTING menu appears.
3Press the [+] or [,] key until SIZE...

Making copies5
bizhub 163/211 5-45
4Press the [+] or [,] key until SIZE INPUT is selected, and then press 
the [OK] key.
5Use the keypad to type in 250 for the length (X), and then press the 
[OK] key.
– The paper length (X) can be set between 140 mm and 432 mm.
– Refer to the diagram at the right 
and be sure to specify the paper 
width and length measurements 
correctly.
BYPASS PAPER SIZE
SIZE INPUT
INCH
MEMORY1:[216/279]
BYPASS PAPER SIZE
 Y=279( 90-297)
 X=250(140-432)  x
length (X)
width (Y)...

5Making copies
5-46 bizhub 163/211
6Use the keypad to type in 180 for the width (Y), and then press the 
[OK] key.
– The paper width (Y) can be set between 90 mm and 297 mm.
The BYPASS PAPER SETTING menu appears again.
7Check that MEDIA: PLAIN appears in the third line of the screen.
– If any paper type setting other than that for plain paper is selected, 
select MEDIA, and then select PLAIN.
8Press the [+] or [,] key until RETURN is selected, and then press the 
[OK] key.
The main screen appears.
BYPASS...

Making copies5
bizhub 163/211 5-47
9If necessary, specify any other copy settings.
– Refer to Before making copies on page 4-3.
– Refer to Advanced copy operations on page 6-3.
10Press the [Start] key.
– When making continuous copies using the manual bypass tray, 
continue loading paper into the tray.
2
Note 
To correct the entered value, press the [Clear/Stop] key.
Downloaded From ManualsPrinter.com Manuals 

5Making copies
5-48 bizhub 163/211Copying onto envelopes
As an example, the following procedure describes how to make copies onto 
200 mm e 150 mm envelopes loaded into the manual bypass tray or the multi 
bypass tray.
2
Note 
When loading non-standard-sized documents and paper, be sure to first 
measure their sizes.
The document scales at the edges of the original glass are useful for 
measuring documents and paper.
1Position the document to be copied.
– Refer to Loading the document on page 4-18....

Making copies5
bizhub 163/211 5-49– A maximum of 10 envelopes can be loaded into the multi bypass 
tray. Do not load so many envelopes into the multi bypass tray that 
the top of the stack is higher than the , mark.
The BYPASS PAPER SETTING menu appears.
3Press the [+] or [,] key until SIZE is selected, and then press the [OK] 
key.
BYPASS PAPER SETTING
 MEDIA:PLAIN
RETURN
SIZE:
Downloaded From ManualsPrinter.com Manuals 

5Making copies
5-50 bizhub 163/211
4Press the [+] or [,] key until SIZE INPUT is selected, and then press 
the [OK] key.
5Use the keypad to type in 200 for the length (X), and then press the 
[OK] key.
– The paper length (X) can be set between 140 mm and 432 mm.
– Refer to the diagram at the right 
and be sure to specify the paper 
width and length measurements 
correctly.
BYPASS PAPER SIZE
SIZE INPUT
INCH
MEMORY1:[216/279]
BYPASS PAPER SIZE
 Y=279( 90-297)
 X=200(140-432)  x
length (X)
width (Y)...