KitchenAid Professional 5 Service Manual

KITCHENAID
Stand Mixer Service Manual LIT4177310-C                          2005 KitchenAid
If not, adjust the bowl height by turning the beater 
height adjusting screw clockwise to decrease the 
clearance or counter clockwise to increase the bowl to 
beater clearance (Fig. 97).
Fig. 97 Adjusting the beater to bowl height using the 
adjusting screw.
Q.  Both “Bowl Lift’and “Tilt Head”international 
export models require an “R F”filter that is mounted 
to the bottom cover of the motor housing with a...

KITCHENAID
Stand Mixer Service Manual LIT4177310-C                          2005 KitchenAid
.  
APPENDIX 

KITCHENAID
Stand Mixer Service Manual LIT4177310-C                          2005 KitchenAid
.  
Appendix -A
Tools Required for Stand Mixer Service
Mallet
Hammer
Needle Nose Pliers
Ratchet
#3 Phillips 
Bit
11/32”Wrench
Long Flat Screwdriver
Short Flat Screwdriver
3/8”Hollow Shank Nut Driver 
5/32”Drift Punch
Volt / Ohm Meter
Watt Meter
Electronic Speed
Measuring  Device
#2 Phillips Screwdriver
Cradle -Make your 
own from wood, 
cushion with cloth to 
avoid damage to finish 
of mixer.
A
B
C
D
E
E
A -7”
B...

KITCHENAID
Stand Mixer Service Manual LIT4177310-C                          2005 KitchenAid
PROBLEM SOLVING QUICK REFERENCE GUIDE
Appendix B-1
MIXER PROBLEMMOST LIKELY CAUSE(S)WHAT TO DO / CHECK 
Switch lever clicks, but mixer will notOpen electrical circuit.Faulty plug.
 run or buzz.Faulty power cord.
Faulty speed control plate.
Wire loose from brush holder.
Bad connection between field and cord.
Open circuited armature.
Open circuited field.
Faulty switch ON/OFF.
Bad phase control.
Dirty contacts....

KITCHENAID

Stand Mixer Service Manual LIT4177310-C                          2005 KitchenAid
Appendix B-1
FASTENER REQUIREMENTS
A.   FASTENER AND TORQUE VALUES
LISTED BELOW ARE THE FASTENERS AND TORQUE VALUES USED IN THE ASSEMBLY OF THE KITCHENAID.
DESCRIPTIONTORQUE IN LBS.
BASE & COLUMN MOUNTING SCREWS (4)(K45)125/150
BEARING BRACKET ASSEMBLY RETAINING NUTS (2)15/20
BOWL SCREW CAP RETAINING SCREWS (3)(K45)24/32
BOWL SPRING MOUNTING SCREWS (2)(K5)18/23
BOWL SUPPORT MOUNTING SCREWS (2)(K5)18/23
BRUSH...

KITCHENAID
Stand Mixer Service Manual LIT4177310-C                          2005 KitchenAid
PROBLEM SOLVING QUICK REFERENCE GUIDE
Appendix B-2
MIXER PROBLEMMOST LIKELY CAUSE(S)WHAT TO DO / CHECK
Mixer runs only on high speed.Control plate spring unhooked.Remove end cover and check control plate spring.
If unhooked, reattach to bottom of the control plate
(check hook on end - rebend if necessary).
Phase control shorted.With the line cord disconnected, pull the T-bar
contacts open and insert a piece of...

KITCHENAID
Stand Mixer Service Manual LIT4177310-C                          2005 KitchenAid
PROBLEM SOLVING QUICK REFERENCE GUIDE
Appendix B-3
MIXER PROBLEMMOST LIKELY CAUSE(S)WHAT TO DO / CHECK
Switch lever clicks, but mixer will not Open electrical circuit.Progressively disassemble the speed control 
run or buzz.mechanism plus the motor and perform the
following checks until the open circuit is found.
Look for:
Faulty plug on power cord.
Faulty power cord.
Bad connection in speed control plate.
Faulty...

KITCHENAID
Stand Mixer Service Manual LIT4177310-C                          2005 KitchenAid
Appendix C
STAND MIXER WIRING DIAGRAM 
DOMESTIC MODELS
Adjust these screws equally to give
60 R P M at the planetary on Stir Speed.
If using a digital tachometer at the 
attachment hub, set the reading to 40 -64
R P M on Stir Speed.
Adjust this screw to give 175 -180 R P M  at the planetary for speed 6 after Stir Speed  has been adjusted. If using a digital tachometer at the attachment hub, set the  reading at...

KITCHENAID
Stand Mixer Service Manual LIT4177310-C                          2005 KitchenAid
.  
Appendix D
STAND MIXER WIRING DIAGRAM
INTERNATIONAL MODELS -R F FILTER
Adjust these screws equally to give 60 R P M at the planetary on Stir Speed.If using a digital tachometer at the attachment hub, set the reading to 40 -64 R P M on Stir Speed.
Adjust this screw to give 175 -
180 R P M at the planetary for
Speed  6 after Stir Speed has been
adjusted. If using a digital
tachometer at the attachment hub, 
set...

KITCHENAID
Stand Mixer Service Manual LIT4177310-C                          2005 KitchenAid
.  
Appendix E
STAND MIXER WIRING DIAGRAM
INTERNATIONAL MODELS -BOWL LIFT and R F FILTER
Adjust these screws equally to give
60 R P M at the planetary on Stir Speed.
If using a digital tachometer at the 
attachment hub, set the reading to 40 -64
R P M on Stir Speed.
Adjust this screw  to give 175
-180 R P M  at the planetary forspeed 6 after Stir Speed  has beenadjusted. If using a digitaltachometer at the...