KitchenAid Professional 5 Service Manual
Here you can view all the pages of manual KitchenAid Professional 5 Service Manual. The KitchenAid manuals for Stand Mixer are available online for free. You can easily download all the documents as PDF.
Page 21
KITCHENAID Stand Mixer Service Manual LIT4177310-C 2005 KitchenAid I. Start a new pinion gear and shaft from the bottom of the bracket. Before the shaft emerges from the lower bearing, place a washer on the bearing and start the shaft into the washer. Place a new worm gear next and push the shaft up into it. Place the second washer on top of the worm gear and push the pinion shaft up into the upper bearing. Line up the drive pin holes in the shaft and worm gear and drive...
Page 22
KITCHENAID Stand Mixer Service Manual LIT4177310-C 2005 KitchenAid P.If necessary to replace the internal gear, pry it from the bottom cover (Fig. 61). Fig. 61 Internal gear can be pried from the bottom cover and replaced if necessary. When installing new gear, start with beveled side down; align notches with holes in gear case and tap evenly into place using a non-metallic mallet. Insert and tighten the five special screws evenly (Fig. 62) to 18 -20 in. lbs. torque. Fig. 62...
Page 23
KITCHENAID Stand Mixer Service Manual LIT4177310-C 2005 KitchenAid S. The agitator shaft is complete as an assembly. Lubricate the shaft and push it up into the bearing as far as it will go. Place the washer(s) on the shaft. Insert the pin through the shaft. Set the pinion gear on the shaft so that the notches in the pinion align with the pin in the shaft. Install the retaining clip in the groove on the shaft (Fig. 64). Fig. 66 The planetary components are shown...
Page 24
KITCHENAID Stand Mixer Service Manual LIT4177310-C 2005 KitchenAid . SECTION 5 REPAIRS TO TILT HEAD PEDESTALS A.If pedestal is removed, check the hinge pin. If it is galled from failure to loosen the set screw, replace it (Fig. 70). Fig. 70 The set screw in the bottom of the pedestal should clear the hinge pin. Loosen the set screw so that it will clear the hinge pin. Place the new hinge pin in the pedestal, but do not drive it in. B.Check the rubber feet. If they are...
Page 25
KITCHENAID Stand Mixer Service Manual LIT4177310-C 2005 KitchenAid F. On international export models shown (Fig. 74), a plastic head lock foot has been riveted to the pedestal to permit the locking of the motor housing in the “inclined”position. The lock lever on these models is spring loaded and the locking action is obtained by removing tension from the lever after the motor housing has been put in the “inclined”position (Fig. 74). Fig. 74 A plastic headlock has been...
Page 26
KITCHENAID Stand Mixer Service Manual LIT4177310-C 2005 KitchenAid Fig. 77 Carefully let the planetary touch your finger to test speeds. Fig. 78 Once proper speed setting has been obtained, lock the two 11/32”lock nuts. If a small correction must be made, make it without loosening the lock nuts. Test speeds as before, and, when correct, it will not be necessary to disturb the lock nuts. E. Move the switch lever to speed #6. At this setting, the planetary must turn at 180...
Page 27
KITCHENAID Stand Mixer Service Manual LIT4177310-C 2005 KitchenAid The control plate is spaced 3/8”from the mounting bracket for the proper speed setting “Starting Point.” Plug the mixer into a watt meter set at the proper voltage. Turn the mixer to “Stir Speed.”The mixer may or may not start. If not, turn the two mounting screws out evenly until mixer starts. Adjust both screws evenly until a speed setting of 40(40 -64) is attained. Turn mixer to speed #6. The single...
Page 28
KITCHENAID Stand Mixer Service Manual LIT4177310-C 2005 KitchenAid SECTION 7. REPAIRS TO BOWL LIFT ASSEMBLIES ON BOWL LIFT MODELS A. The bowl lift models of KitchenAid mixers have a different type of bowl and are different in size. On the tilt head models, the bowl is held stationary by mechanical means at the bottom of the mixer pedestal; whereas, on bowl lift models, the bowl support slides up and down gibs on the column. B.Should the mixer be tipped over or knocked off...
Page 29
KITCHENAID Stand Mixer Service Manual LIT4177310-C 2005 KitchenAid Fig. 88 Slide the bowl support down and off the column to replace the bowl lift assembly. G. To install the new bowl lift arm, drive out the roll pin (Fig. 89). With the roll pin out, remove the bowl lift handle (Fig. 90). The bowl lift arm can now be removed along with the bowl lift mechanism. Fig. 89 Drive out the roll pin to remove the bowl lift arm. Fig.90 With the roll pin removed, pull out the...
Page 30
KITCHENAID Stand Mixer Service Manual LIT4177310-C 2005 KitchenAid K. If the mixer base feet are worn, replace them. To replace the mixer base feet, pull them out, using pliers and a twisting motion. Older models require the removal of four # 8-32 x 1/2”round head screws to remove the feet (Fig. 93). Fig. 93 Remove the four round head screws to remove the feet from older models. Install new feet by pushing the tapered end into the foot supports with a twisting motion...