Keurig 20 K300 Owners Manual

							USING YOUR BREWER
OWNER’S MANUAL: Getting the most from your new 
Special Edition B60  Keurig® Brewer
COMMENT UTILISER VOTRE CAFETIÈRE
MANUEL D’UTILISATION : Tirez le meilleur de votre   
nouvelle cafetière Édition spéciale B60 de Keurig
® 
						

							3
IMPORTANT SAFEGUARDS Safe Operation & Use
2
WARNING TO USERS AND PARENTS
1. DO NOT permit children to use brewer unless there 
is adult supervision.  Brewer dispenses very hot water.
2. SPECIAL NOTICE FOR HOT COCOA USERS:    
IMMEDIATELY AFTER USING A HOT COCOA K-CUP,   
RUN a Hot Water Brew Cycle  without a K-Cup to avoid 
the possibility of clogging the exit needle.  DO NOT assume 
the next user will do this. 
When using electrical appliances, basic   
safety precautions should be followed,   
including the following:
1. 
  Read all instructions before using.
2.   
Do not touch hot surfaces. Use handle and
knobs when available.
3.   This appliance must be properly installed and 
located in accordance with these instructions 
before it is used.
4.   The use of accessory attachments not recom -
mended by the appliance manufacturer may re -
sult in fire, electrical shock or injury to persons.
5.   
Do not place on or near a hot gas or electric 
burner, or in a heated oven.
6. Do not use outdoors.
7.   To protect against fire, electric shock and injury, 
do not immerse cords, plugs or the appliance in 
water or any other liquid.
8. Do not overfill the Water Reservoir with water.
9.   Use  only water  in this appliance! Do not put any 
other liquids or foods in the Water Reservoir, 
except as instructed in the Cleaning Instructions 
in this guide.
10.    Turn off and unplug the Brewer before 
cleaning or maintenance. Allow to cool   before putting on or taking off parts and 
 
before cleaning the appliance.
11.    For best operation, plug the appliance into
its own electrical outlet on a dedicated circuit 
to prevent flickering of lights, blowing of fuses 
or tripping a circuit breaker.
12.   Do not operate any appliance with a damaged 
cord or plug, or after the appliance malfunc -
tions or is damaged in any manner. Contact 
Keurig Customer Service to report any   
malfunction of or damage to the Brewer.
13.    Do not let the cord hang over the edge
of the table or counter, or touch hot surfaces.
14.   To disconnect, press the Power Button on
the back of the Brewer to “OFF” status, and 
then remove the plug from the wall outlet.
15.   Close supervision is necessary when
any appliance is used by or near children.
16.    Do not lift the Brewer Handle while   
brewing is in progress.
17.   
Always keep the Water Reservoir Lid on the 
Water Reservoir unless you are refilling it.
18.   This appliance is equipped with a power
cord having a grounding wire with a 
grounding plug. The appliance must be  grounded using a 3-hole, properly grounded 
outlet. In the event of an electrical short 
circuit, grounding reduces the risk of 
electrical shock.
19. 
  If the outlet is a standard 2-prong wall
outlet, it is your personal responsibility 
and obligation to have it replaced with a 
properly grounded 3-prong wall outlet.
20.   Do not, under any circumstances, cut or
remove the third (ground) prong from 
the power cord or use an adapter.
21.   Consult a qualified electrician if the
grounding instructions are not completely 
understood or if doubt exists as to whether 
the appliance is properly grounded.
22.   Do not use the appliance for any reason 
other than its intended use. 
S Av E  T HESE  INSTRUCTIONS . 
						

							3
CAUTION: There are two sharp needles that puncture the K-Cup® portion pack, 
one above the K-Cup Holder and the other in the bottom of the K-Cup Holder. To 
avoid risk of injury, do not put your fingers in the K-Cup Assembly Housing.
CAUTION: There is extremely hot water in the K-Cup Holder during the 
brew  process. To avoid risk of injury, do not lift the Handle or open the K-Cup 
Assembly Housing during the brewing process.
SHORT CORD INSTRUCTIONS:
 A short power supply cord is provided to 
reduce the risk of becoming entangled in or tripping over a longer cord.
If an extension cord is used, (1) the marked electrical rating of the cord set 
or extension cord should be at least as great as the electrical rating of the 
appliance; (2) the cord should be arranged so that it will not drape over the 
countertop or tabletop where it can be pulled on by children or tripped over un -
intentionally; and (3) the extension cord must include a 3-prong grounding plug.
THIS PRODUCT IS FOR  HOUSEHOLD USE ONLY.
WARNING THIS PRODUCT CONTAINS CHEMICALS, INCLUDING 
LEAD, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, 
BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
TABLE OF CONTENTS
KEURIG® GOURMET SINGLE CUP HOME BREWING SYSTEM
Special Edition  —  Model B60   
Using Your Brewer
SET-UP
Helpful Hints  ........................................................................................
4
Unpacking  ............................................................................................4
Features  ...............................................................................................5
SECTION 1  —  SET-UP & FIRST BREW
Set-Up & First Brew  ...........................................................................6
SECTION 2  —  CONTROLS & INDICATORS
Setting the Clock  ...............................................................................10
Programming On/Off Features  ......................................................10
Programming Brew Temperature  .................................................12
SECTION 3  —  CLEANING & MAINTENANCE
Cleaning  ..............................................................................................12
De-Scaling ..........................................................................................13
Storage ...............................................................................................14
SECTION 4  —  TROUBLESHOOTING ..................................................15
SECTION 5   —  WARRANTY ................................................................16
 
Pour des directives en français, veuillez vous reporter à la page 17.
Record your Brewer Serial Number here.
Removing the serial number label from the brewer will void warranty. 
WARNING
WARNING: TO REDUCE THE RISK OF FIRE OR 
ELECTRIC SHOCK, DO NOT REMOVE THE 
BOTTOM COVER. NO USER SERVICEABLE 
PARTS ARE INSIDE. REPAIR SHOULD BE DONE 
BY AUTHORIZED SERVICE PERSONNEL ONLY.
RISK OF FIRE OR  
ELECTRIC SHOCK   DO NOT OPEN
!  
						

							Set-Up
Helpful Hints 
1.  
Keep your Brewer turned “ON” at all times.   
To brew a fresh cup of coffee, tea or hot cocoa 
anytime you want, we suggest you keep your 
Brewer turned “ON” all the time. However, the 
Brewer is fully programmable so you can set it 
to turn on and off automatically to match your  schedule. Or, if you prefer, set the Brewer to   
automatically turn off after a period of time. 
Follow the simple instructions on pages 10–12 
to make using the Brewer convenient for you.
2.    For the best tasting gourmet coffee, tea or 
hot cocoa, Keurig recommends using bottled 
or filtered water. 
Water quality varies from place to place. If you  notice an undesirable taste in your cup of   
coffee, such as chlorine or other mineral tastes, 
we recommend you consider using bottled 
water or water from a filtration system.
3.    Customize the Size, Flavor & Brew That’s   
Perfect for You. 
With the choice of over 200 varieties of K-Cups 
and 3 brew sizes (Small Cup-5.25 oz., Small 
Mug-7.25 oz. and Large Mug-9.25 oz.) your 
Keurig Brewer gives you endless options to  customize the size, flavor and brew that’s 
perfect for you. For a strong, intense cup, select an Extra Bold K-Cup (with up to 30% more  ground coffee than regular varieties) and brew 
size that’s right for you. The smaller the brew 
size, the more intense flavor in your cup. The  larger the brew size, the less intense flavor in 
your cup. 
4.    Plug Brewer into its own grounded outlet. 
If the electric circuit is overloaded with other 
appliances, your Brewer may not function 
properly. The Brewer should be operated on its  own circuit, separate from other appliances.
5.   
Brewing into a travel mug. 
To brew into a travel mug, simply remove the 
Drip Tray Assembly and place the travel mug on the Drip Tray Base.
6.   
De-Scale Brewer regularly.    
Please see page 13 for instructions.
Unpacking Instructions
1.  
Place Brewer box on a large steady surface
(such as a table or countertop) or on the floor.  Open the box.
2. Remove enclosed literature.
3.  
Turn the box on its side with front of box face down.
4.   Reach into the box and grasp the plastic bag 
that contains the Brewer.
5.   Carefully pull the plastic bag (and packaging 
materials) toward you and out of the box. The 
Brewer will still be encased in the polyfoam   
and be on its side.
6.  
Remove the top polyfoam packaging material.
7.  
Carefully lift Brewer off of the bottom polyfoam 
and place it upright on a flat, steady surface.
8.   Lift plastic bag off of Brewer.
9.  
Record the serial number for this Brewer on 
page 3 of this guide. The serial number can be 
found on the bottom of the Brewer box or on the  Brewer behind the Drip Tray (when removed).
10.  
Place the Brewer upright on a flat, steady 
surface. Remove tape holding Water Reservoir  in place. 
We recommend you save all packing materials in  case future shipping of the product is necessary.
WARNING: 
Keep all plastic bags away   
from children.
4 
						

							5
11 :
5 6AM
READY
TO BREW
MENU
Features  Special Edition — Model B60 Brewer
A
B
M
C
IN
LK
J
H
E
F
GDT
R
S
0PQ
A.  Water Reservoir Lid
B. Water Reservoir
C. Water Reservoir 
Lock Tab Slots
D.  Handle
E. Funnel
F. K-Cup® Portion Pack 
Holder (E and F are the   
K-Cup Holder Assembly) 
G.  Lid
H. K-Cup Portion 
Pack Assembly   
Housing
I.  Housing
J. Drip Tray Plate
K. Drip Tray
L. Drip Tray Base
M. Vent
N. Power Cord
O. Small Cup Button 5.25 oz.
P. Small Mug Button 7.25 oz.
Q. Large Mug Button 9.25 oz.
R. Menu Button
S. LCD Control Center
T. Power Button
Special Edition B60 Brewer Controls and Indicators  
						

							67
SECTION 1  Set-Up & First Brew
Setting Up Your Brewer
1.  
Unwrap cord and plug the Brewer into 
a grounded outlet. Remove all pieces of   
packing tape and clear plastic sticker   
from LCD display.
2. Place a large mug (10 oz. min) on the 
    Drip Tray Plate.
3.   
Remove the Water Reservoir from Brewer 
by first removing Lid from Reservoir (fig. 1), 
then lifting Reservoir straight up and away   
from Brewer (may be tight), (fig. 2). Rinse   
with fresh water.
IMPORTANT: You cannot use your Keurig Brewer until 
it has been set-up for its first use as set forth below.
NOTE: If Brewer has been exposed to temperatures
below freezing, allow Brewer at least two hours to 
reach room temperature before brewing. A frozen   
or extremely cold brewer will not operate.
4.    Fill Water Reservoir with bottled or filtered 
water so that the water level is just below the 
top edge of the Water Reservoir.
5.   Place Water Reservoir base into the left side 
of the Brewer and be sure the Water Reservoir 
Lock Tabs engage with the Brewer. Replace Lid 
on Water Reservoir.
6.     Press the Power Button found directly
above the LCD Control Center (fig. 3).
7.   
The LCD Control Center will come on and
indicate “NOT READY” and the Small Mug   
Button will also flash. 
NOTE: A K-Cup should 
not be used for this Sequence
.
8.    Press the Small Mug Button (fig. 3). NOTE: If the Water Reservoir is empty or 
not in place on the Brewer, the LCD Control   
Center will also indicate “ADD WATER.” None   
of the buttons will be activated until water is 
added to the Water Reservoir.
fig. 2
Power
Small  Mug 
     ADD 
WATER
NOT READY
fig. 3
fig. 1
Lock Tabs             
						

							67
Ready to Brew Your First Cup
 1.  
LCD Control Center will indicate 
“READY TO BREW”. 
2. Place a cup or mug on the Drip Tray Plate.
3.   Lift the Handle and the K-Cup Holder  
will open toward you (fig. 6).
4.   Select a K-Cup® portion pack.NOTE: Do not remove the foil lid or
puncture the K-Cup.
5.   
Place a K-Cup portion pack in the 
K-Cup Holder (fig. 7). 
CAUTION: There are two sharp needles that
puncture the K-Cup, one above the K-Cup Holder 
and the other in the bottom of the K-Cup Holder. 
To avoid risk of injury, do not put your fingers in 
the K-Cup Assembly Housing.
6.    
Lower the Handle to close the Lid over the
K-Cup Holder. (When it is closed completely, 
the LCD Control Center will indicate “READY 
TO BREW” and the Small Cup, Small Mug and 
Large Mug Buttons will flash up to 60 seconds.)
9.     The Brewer will automatically fill the internal 
tank with water and then the water will be heat -
ed. This will take about 4 minutes. During the 
heating period, “NOT READY” (fig. 4) is displayed 
on the LCD Control Center.  Do not lift Brewer 
Handle during this ‘heating period’ . Once 
the water is heated, “READY” will be displayed 
and the Small Mug Button will flash (fig. 5).   
NOTE: You may see small amounts of water 
coming from the Vent and dripping into the   
Water Reservoir during this and subsequent heat -
ing  —  this is normal.
10.
   
Press the Small Mug Button to start a 
cleansing brew. Pour the hot water into   
the sink.
11.    The one-time set-up process is now 
complete and you are ready to brew! 
NOTE: The Brewer may take 15 seconds 
between brews and then “READY TO BREW”   
will be displayed.
NOT READY
Small  Mug 
READY
TO BREW
fig. 4
fig. 5
fig. 6
fig. 7          
						

							89
7.  
Choose the brew size of coffee, tea or hot cocoa 
by pressing the button that indicates your 
choice. The Large Mug choice will yield a 9.25 oz.  serving, the Small Mug choice will yield a 7.25 oz. 
serving, and the Small Cup choice will yield   
a 5.25 oz. serving. 
NOTE: If you do not push the Brew Buttons in 
60 seconds, the LCD Control Center will return   
to “READY TO BREW” and the Brew Buttons will   
be disabled to prevent accidental activation.   
Re-activate the Brew Buttons by raising and   
lowering the Handle completely.
8.
    The LCD Control Center will now display the 
word “BREWING” and the brew size you   
selected will be solid blue.   
CAUTION: There is extremely hot water in the 
K-Cup Holder during the brew process. To avoid 
risk of injury, do not lift the Handle or open the   
K-Cup Assembly Housing during the brew process.
9.
   
There may be a short pause prior to coffee 
being dispensed. The entire brew process lasts 
for approximately 1 minute and ends with a 
burst of air to remove all liquid from the K-Cup.
Brewing Your First Cup   (Continued) 10.  
Lift the Handle, remove and dispose of the 
used K-Cup.   
CAUTION: K-Cup will be hot.
11.
   
Enjoy your first cup of Keurig Brewed® 
gourmet coffee, tea or hot cocoa!
12.   
Your Brewer may display “NOT READY” as 
it heats water for the next brew cycle. The 
“READY TO BREW” indication will return to   
the LCD Control Center in about 15 seconds.
NOTE: Following the brew, your Brewer will
fill in preparation for the next brew. The pump 
will make a vibrating sound. This is normal.
Stopping the Brew Process
If you need to stop brewing after the process has started, press the Power 
Button to turn the Brewer “OFF.” The flow of coffee, tea or hot cocoa will stop,  the heating element will shut off, and the blue lights illuminating the brew 
buttons and Water Reservoir will disappear. 
NOTE: You may get less coffee, tea or hot cocoa in your cup during your next 
brew. We recommend that you perform a cleansing brew with water-only after   
a terminated brew. Then your NEXT brew will be the volume you have selected.
SECTION 1 Set-Up & First Brew
Small Cup
(5.25 oz.) 
Small Mug
(7.25 oz.) 
Large Mug
(9.25 oz.)      
						

							89
Adding Water
The LCD Control Center of your Brewer will  indicate when the water level in the Water   
Reservoir is low or if the Water Reservoir has  been removed by displaying the words “ADD 
WATER” (fig. 8). The blue light in the Water 
Reser voir will also blink when water needs to  be added. The Brewer will not allow you to brew   
when “ADD WATER” is displayed.
The Water Reservoir can be filled in two ways. 
1. 
 
Lift off the Water Reservoir Lid and pour  water directly into the Water Reservoir   
while it is still attached to the Brewer,   
then replace the Lid.
2.   
Remove the Water Reservoir from Brewer by first removing Lid from 
the Water Reservoir, then lifting the Water Reservoir straight up and   
away from Brewer. Fill with water. Place the Water Reservoir back on   
the Brewer and replace the Lid.
IMPORTANT : Do not remove the Water Reservoir during the 
brewing process.
Brewing Hot Water
Your Brewer is able to produce hot water for making hot cocoa from a packet, 
for use in cooking, for making soups, etc. Simply raise and lower   
the Handle on the Brewer without adding a K-Cup. The LCD Control Center 
will display “READY TO BREW” and the Small Cup, Small Mug and Large 
Mug Buttons will blink. Be sure to have a mug or cup on the Drip Tray Plate 
and then select the size you would like.   
 
NOTE: After brewing a hot cocoa K-Cup, we recommend running a hot water   
 brew cycle without a K-Cup.
Purging the Brewer
If your Brewer has not been used for more than one week, you should purge 
the water from the inner tank.
1.   
If there is water in the Water Reservoir, remove the Lid, then lift the 
Water Reservoir straight up and away from Brewer. Discard water, rinse 
and refill with water. Place the Water Reservoir back on the Brewer and  replace the Lid. (If there is no water in the Water Reservoir, simply refill.)
2.   
Be sure the Brewer is turned on. Raise and lower the Handle on the 
Brewer without inserting a K-Cup.
3.   
The LCD Control Center will display “READY TO BREW” and the Small Cup, 
Small Mug and Large Mug Buttons will blink. Be sure to have a large mug 
on the Drip Tray Plate and then select the Large Mug size brew.
4.   
Repeat steps 2 and 3 one more time to completely purge water from 
inner tank.
If you are experiencing any problems with your Brewer, please contact   
Customer Service at 1.866.901.BREW (2739).
 
   
   ADD 
WATER
NOT READY
fig
. 8   
						

							1011
SECTION 2  Controls & Indicators (LCD Control Center)
Setting the Clock
Setting the clock is optional. When the clock is set, the time will appear in the LCD Control Center. 
NOTE: You must set the clock if you will be using the 
On/Off Time programming feature.
1. 
Press the Menu Button.
2.  
The word “OFF” will appear at the bottom 
of the LCD Control Center to indicate that   
the clock is not set. The programming options  will appear on the LCD Control Center with a 
small arrow pointing to “SET CLOCK” (fig. 9). 
“H” (Hour) and “M” (Minute) will appear and  blink.
3.  
Press or hold the blue Small Cup Button 
under the blinking “H” until you have reached  the appropriate hour. If the hour has passed 
12, the indicator switches from “AM” to “PM”.
4.   
Press or hold the blue Large Mug Button 
under the blinking “M” to set the minutes.
5.   
When you have reached the correct time, press the Menu Button five 
times to scroll through the remaining programming options and exit   
the programming mode.
6.   
The correct time should now be displayed in the LCD Control Center.NOTE: If power is interrupted to the Brewer by unplugging it, or if power 
is lost, follow the procedure above to reset the time as the clock will not be 
visible until the time is set. 
Menu
SET CLOCK
  AUTO OFF
  ON OFF TIME
  BREW TEMP
Set
Hours Set
Minutes
MENU
fig . 9
Programming On/Off Features
The Brewer provides three modes so that you can enjoy gourmet coffee, tea 
or hot cocoa on your own schedule. By programming your Brewer to turn on 
each morning, you will never have to wait for the Brewer to warm up to brew a gourmet cup of coffee.
1.    Leave it ON all the time. The Brewer can be left on all the time so that it is 
always ready to brew a fresh cup of gourmet coffee, tea or hot cocoa. To  turn the Brewer off at any time, simply press the Power Button. 
( NOTE :
 
Although the clock remains on if set, you can not brew a cup of coffee, tea or 
hot cocoa.) 
Press the Power Button again to restore power to the Brewer. 
You will have to wait for the water to heat up before the Brewer is ready to  brew.
2.   
Set the Brewer to Auto Off following a 
specified period of time after the last brew. 
 
a.   
Press the Menu Button twice to program the 
Auto Off feature. The LCD Control Center will  now display the programming options with a 
small arrow next to “SET AUTO OFF” (fig. 10).
b.   
Press or hold the blue Small Cup Button   
under the blinking “H” to advance 1 hour at   
a time, up to 9 hours. 
Menu x2
SET CLOCK
  AUTO OFF
  ON OFF TIME
  BREW TEMP
MENU
fig. 10