Kenwood Tk 860h Manual

11
TK-860G/862G
REALIGNMENT
5-4. Programming Software Description
The KPG-56D programming disk is supplied in 3-1/2 disk
format.  The software on this disk allows a user to program
TK-860G/862G radio via a programming interface cable
(KPG-46).
5-5. Programming With IBM PC
If data is transferred to the transceiver from an IBM PC
with the KPG-56D, the destination data (basic radio informa-
tion) for each set can be modified.  Normally, it is not neces-
sary to modify the destination data because their...

12
TK-860G/862G
Note :
You can clone the programmed data between the trans-
ceiver listed below.  Frequency version must be same.
     SlaveTK-360G TK-360G TK-360G TK-360G TK-860G TK-860G TK-860GKMK4M4KMK3TK-370G TK-370G TK-370G TK-370G TK-862G TK-862G
Master K M K4 M4 K M
TK-860G YES NO NO NO YES NO NO
K
TK-860G NO YES NO NO NO YES NO
M
TK-860G NO NO YES NO NO NO YES
K3
REALIGNMENT
Cloning cable
(E30-3382-05)
Fig. 2
MBL
PSB
GND
PTT/TXD
ME
MIC
HOOK/RXDCM
GND
REMOTE/TXD PTT/RXD
8 1
1 8
Clone cable...

13
TK-860G/862G
9. Channel Setting Mode
Each channel can be setup in its action mode by using
the panel keys.
• Pressing [MON] when SELF is diaplyed, sets channel
setting mode.
• Select an item set using [
] then change the selection
with the [CH
 /].
• The data displayed using [D/A] is stored in the memory
and then proceeds to the next item.
• Pressing [
] proceeds to the next item without storing it
in the memory.
• Press [MON] to set the display to SELF and return to
reset (default) status.
The setup...

14
TK-860G/862G
REALIGNMENT
No. FunctionChoices Display Remarks
9 RF High power PWR_H___←Default
power Low power PWR_L___
10 Wide/ Wide WIDE____
Narrow Narrow NARROW__
11 Scan DELETE SCAN_DEL Not used for 8ch
Delete/AddADD SCAN_ADD←Default
12 Priority No P.CH_NO__ Not used when (Scan)
channel Yes P.CH_YES_ priority is not fixed
13 Home No H.CH_NO__ Not used when home
channel Yes H.CH_YES_ channel is not set in
key assignment
14
CompanderNo COMP_NO_ Not used when wide
is selected
Yes COMP_YES
15 PTT ID...

15
TK-860G/862G
10. Function Setting Mode
All channels can be set up together in the action mode by
using the panel keys.
• Pressing [
] when SELF is displayed, sets the function
setting mode.
• Select an item set using [
] then change the selection
with the [CH
/].
• The data displayed using [D/A] is stored in the memory
and then proceeds to the next item.
• Pressing [
] proceeds to the next item without storing it
in the memory.
• Press [
] to display SELF and return to reset (default)
status.
No....

16
TK-860G/862G
No. FunctionChoices Display Remarks
Horn alert KEY3__14
Selectable QT KEY3__15 M destination only
TK-862G cannot be selected
2-tone encode KEY3__16
select
Monitor A KEY3__17
Monitor B KEY3__18
Monitor C KEY3__19
Monitor D KEY3__20
Scan KEY3__22TK-862G cannot be selected
Scan del/add KEY3__23TK-862G cannot be selected
Group down KEY3__24TK-862G cannot be selected
Group up KEY3__25TK-862G cannot be selected
5[] No function KEY4_OFF←Default
(TK-860G)Volume down KEY4__1_
[A] Volume up...

17
TK-860G/862G
No. FunctionChoices Display Remarks
Public addressCUP___12
Horn alert CUP___14
Selectable QT CUP___15 M destination only
TK-862G cannot be selected
2-tone encode CUP___16
select
Monitor A CUP___17
Monitor B CUP___18
Monitor C CUP___19
Monitor D CUP___20
Scan CUP___22TK-862G cannot be selected
Scan del/add CUP___23TK-862G cannot be selected
Group down CUP___24TK-862G cannot be selected
Group up CUP___25TK-862G cannot be selected
9 [CH] No function CDN__OFF
(ChannelVolume down CDN___1_...

18
TK-860G/862G
No. FunctionChoices Display Remarks
15
Minimum0~31/1 step MVOL_12_
volume
16Off hookEnable H_D__ENA
decode Disable H_D__DIS←Default
17Off hookEnable H_H__ENA
horn alertDisable H_H__DIS←Default
18
Time outOFF, 15~600/ TOT_180_ Default : 180s
timer 15s step
19 TOT OFF, 1~10/ TOTP_OFF Cannot be set when
pre-alert1s step TOT is off
time Default : Off
20 TOT OFF, 1~60/ TOTK_OFF Cannot be set when
rekey 1s step TOT is off
time Default : Off
21 TOT OFF, 1~15/ TOTS_OFF Cannot be set when
reset 1s...

19
TK-860G/862G
REALIGNMENT
Self programming
mode
Function setting
mode
[MON] key function[D/A]/[   ][A]/[MON] key function
[D/A]/[   ] key function
[   ]/[   ] key function
[   ]/[A] key function
[SCN] key function
[FOOT] key function
[D/A]/[   ]
[D/A]/[   ]
[D/A]/[   ]
[D/A]/[   ]
[D/A]/[   ]
[CH   ] key function
[D/A]/[   ]
[CH   ] key function
[D/A]/[   ]
[VOL   ] key function
[D/A]/[   ]
[VOL   ] key function
[D/A]/[   ]
Power on tone yes/no
[D/A]/[   ]
Control tone yes/no
[D/A]/[   ]
Warning tone...

20
TK-860G/862G
34
5
6
7
89
1. Accessory Connection Cable
(KCT-19 : Option)
The KCT-19 is an accessory connection cable for con-
necting external equipment.  The connector has 15 pins and
the necessary signal lines are selected for use.
1-1. Installing the KCT-19 in the transceiver
1. Remove the upper and lower halves of the transceiver
case, and lift the DC cord bushing ( ) from the chassis.
2. Remove the pad as shown in Figure 1 ( ).
3. Insert the KCT-19 cable ( ) into the chassis ( ).
The wire harness...