Kenwood Tk 860h Manual

							11
TK-860G/862G
REALIGNMENT
5-4. Programming Software Description
The KPG-56D programming disk is supplied in 3-1/2 disk
format.  The software on this disk allows a user to program
TK-860G/862G radio via a programming interface cable
(KPG-46).
5-5. Programming With IBM PC
If data is transferred to the transceiver from an IBM PC
with the KPG-56D, the destination data (basic radio informa-
tion) for each set can be modified.  Normally, it is not neces-
sary to modify the destination data because their values are
determined automatically when the frequency range (fre-
quency type) is set.
The values should be modified only if necessary.  Data
can be programmed into the flash memory in RS-232C for-
mat via the modular microphone jack.
6. Firmware Programming Mode
6-1. Preface
Flash memory is mounted on the TK-860G/862G.  This
allows the TK-860G/862G to be upgraded when new fea-
tures are released in the future.  (For details on how to ob-
tain the firmware, contact Customer Service.)
6-2. Connection Procedure
Connect the TK-860G/862G to the personal computer
(IBM PC or compatible) with the interface cable (KPG-46).
(Connection is the same as in the PC Mode.)
6-3. Programming
1. Start up the programming software (KPG-56D), select
firmware program in the Program item, and press the
Return key on your personal computer.  This starts up the
firmware programmer.
2. The top screen is displayed.  Press any key to advance to
the next screen.
3. Set the communications speed (normally, 57600 bps)
and communications port in the Setup item.
4. Set the firmware to be updated by File select (=F1).
5. Turn the TK-860G/862G Power ON with the [CH
]
switch held down.  Hold the switch down for two sec-
onds until the display changes to PROG 576, the BUSY/
TX LED lights orange.  When PROG 576 appears, re-
lease your finger from the switch.
6. Check the connection between the TK-860G/862G and
the personal computer, and make sure that the TK-860G/
862G is in Program mode.
7. Press F10 on the personal computer.  A window opens
on the display to indicate the writing progress.  When the
TK-860G/862G starts to receive data, the BUSY/TX LED
lights green.
8. If writing ends successfully, the LED on the TK-860G/
862G goes off and the checksum is displayed.
(Since the TK-862G does not have a display, check the
checksum with the FPU (KPG-56D).)
9. If you want to continue programming other TK-860G/
862G, repeat steps 5 to 8.
4. Check Sum
Executing this function, TUNING apears on the display
of the TK-860G while calculation the check sum.
When the calculation is completed, the display returns to
normal and PC displays the check sum of the radio.
5. PC Mode
5-1. Preface
The TK-860G/862G transceiver is programmed using a
personal computer, a programming interface (KPG-46) and
programming software (KPG-56D).
The programming software can be used with an IBM PC
or compatible.  Figure 1 shows the setup of an IBM PC for
programming.
5-2. Connection Procedure
1. Connect the TK-860G/862G to the personal computer
with the interface cable.
2. When the Power is switched on, user mode can be en-
tered immediately.  When the PC sends a command, the
radio enters PC mode.
When data is transmitted from transceiver, the red LED
blink.
When data is received by the transceiver, the green LED
blink.
Notes :
• The data stored in the personal computer must match
model type when it is written into the flash memory.
• Change the TK-860G/862G to PC mode, then attach the
interface cable.
5-3. KPG-46 Description
   (PC programming interface cable : Option)
The KPG-46 is required to interface the TK-860G/862G to
the computer.  It has a circuit in its D-subconnector (25-pin)
case that converts the RS-232C logic level to the TTL level.
The KPG-46 connects the modular microphone jack of
the TK-860G/862G to the computers RS-232C serial port.
KPG-46
IBM-PC
KPG-56D
TK-860G/862G
Fig. 1 
						

							12
TK-860G/862G
Note :
You can clone the programmed data between the trans-
ceiver listed below.  Frequency version must be same.
     SlaveTK-360G TK-360G TK-360G TK-360G TK-860G TK-860G TK-860GKMK4M4KMK3TK-370G TK-370G TK-370G TK-370G TK-862G TK-862G
Master K M K4 M4 K M
TK-860G YES NO NO NO YES NO NO
K
TK-860G NO YES NO NO NO YES NO
M
TK-860G NO NO YES NO NO NO YES
K3
REALIGNMENT
Cloning cable
(E30-3382-05)
Fig. 2
MBL
PSB
GND
PTT/TXD
ME
MIC
HOOK/RXDCM
GND
REMOTE/TXD PTT/RXD
8 1
1 8
Clone cable
E30-3411-05 (TK-860G → TK-360G/370G)
8. Self Programming Mode (TK-860G only)
Write mode for frequency data and signalling etc.  Mainly
used by the person maintaining the user equipment.
8-1. Enter to the Self Programming Mode
Remove D507 (Figure 3) from the TX-RX unit.  Hold down
the [A] key and turn the power switch on.  When enter the
self programming mode, SELF is displayed.  The mode
changes autoically to Model Select Mode in about one sec-
ond, and set up radio type, radio band & channel type and
frequency version.
Notes :
• To start the Firmware Programmer from KPG-56D, the
FPRO path must be set up by the KPG-56D setup.
• This mode cannot be entered if the Firmware program-
ming mode is set to Disable in the Programming soft-
ware (KPG-56D).
• When programming the firmware, it is recommend to
copy the data from the floppy disk to your hard disk be-
fore you update the radio firmware.
Directly copying from the floppy disk to the radio may not
work because the access speed is too slow.
6-4. Function
1. If you press the [MON] switch while PROG 576 is dis-
played, the checksum is displayed.  If you press the
[MON] switch again (while the checksum is displayed),
PROG 576 is redisplayed.
2. If you press the [A] switch while PROG 576 is displayed,
the display changes to PROG 192 to indicate that the
write speed is low speed (19200 bps).  If you press the
[A] switch again while PROG 192 is displayed, the dis-
play changes to PROG 384, and the write speed be-
comes the middle speed (38400 bps).  If you press the
[A] switch again while PROG 384 is displayed, the dis-
play returns to PROG 576.
Note :
TK-862G indicate
19200 bps : The LED flashes green and red alternately.
38400 bps : The LED flashes orange.
57600 bps : The LED lights orange.
Normally, write in the high-speed mode.
7. Clone Mode
Programming data can be transferred from one radio to
another by connecting them via their modular microphone
jacks.  The operation is as follows (the transmit radio is the
master and the receive radio is the slave).
1. Turn the master TK-860G power ON with the [
] key
held down.  The TK-860G displays CLONE.
2. Power on the slave TK-860G/862G.
3. Connect the cloning cable (No. E30-3382-05) to the
modular microphone jacks on the master and slave.
4. Press the [SCN] key on the master while the master dis-
plays CLONE.  The data of the master is sent to the
slave.  While the slave is receiving the data, –PC– is dis-
played.  When cloning of data is completed, the master
displays END, and the slave automatically operates in
the User mode.  The slave can then be operated by the
same program as the master.
5. The other slave can be continuously cloned.  When the
[SCN] key on the master is pressed while the master dis-
plays END, the master displays CLONE.  Carry out the
operation in step 2 to 4. 
						

							13
TK-860G/862G
9. Channel Setting Mode
Each channel can be setup in its action mode by using
the panel keys.
• Pressing [MON] when SELF is diaplyed, sets channel
setting mode.
• Select an item set using [
] then change the selection
with the [CH
 /].
• The data displayed using [D/A] is stored in the memory
and then proceeds to the next item.
• Pressing [
] proceeds to the next item without storing it
in the memory.
• Press [MON] to set the display to SELF and return to
reset (default) status.
The setup items fro channel setting mode are listed be-
low.
No. FunctionChoices Display Remarks
Select 1~128 __1-__1._ [] : Group selection/
channel __1-128._ Channel selection
Select 1~128 __1.-__1_ change
group 128.-__1_
1 RX Step STP__250 Display when an item
frequency2.5kHz~1MHz STP_1000 is selected or when a
step is changed
(about 0.5 seconds)
[A] : Step change
2.5, 5.0, 6.25kHz,
1MHz step
Blank - - - - - - - - [] : Frequency on/
100.0000~ R.100.0000 blank switching
550.0000MHz The rightmost dot
indicates 50Hz digit
(On=5, Off=0)
2 RX Off - - - - - - - - [] : Off/QT/DQT
signallingQT 67.0~250.3HzQT__67.0_ switching
(EIA mode) QT_250.3_ [A] : Mode switching
QT 67.0~250.3HzQT__67.0* [SCN] : Normal/
(0.1Hz step mode)QT_250.3* Inverse switching
DQT 000~777 DQT000N*
(Normal) DQT777N*
(1 step mode)
DQT 023~754 DQT023N_
(Normal) DQT754N_
(Standard table mode)
DQT 000~777 DQT000I*
(Inverse) DQT777I*
(1 step mode)
DQT 023~754 DQT023I_
(Inverse) DQT754I_
(Standard table mode)
REALIGNMENT
IC502 TX-RX unit  B/2
Foil side
50
51
IC505
1 84
5
D507
D505
Fig. 3 Note :
This mode (self programming mode) cannot be set when
it has been disabled with the FPU.
[D/A]
[D/A]
[   ] [D/A]
[MON][CH
   /   ]Radio type
Channel set
modeFunction set
mode Self programming modePortable
Mobile
Radio band &
channel type
VHF
8CHVHF
128CHUHF
8CHUHF
128CH
Frequency
version
[CH   /   ]
[CH
   /   ][CH
   /   ]
[CH
   /   ]VHF
F1VHF
F2UHF
F1UHF
F3
[CH   /   ]
[CH
   /   ]
[CH
   /   ][CH
   /   ]UHF
F4
[CH
   /   ]
[   ]
Cannot be
set when
portable is
select.Cannot be
set when
mobile is
select.* **
*
8-2. Model Select Mode
• Flow chart
Note :
If the radio type of TK-860G was temporally set to Por-
table for the cloning purposes, UNPROG is displayed (at
User mode) when the TK-860G is turned on.
In this case, please set the radio type back to Mobile at
model select mode menu.The silk screen of D505 and D507 is reversed on the TX-
RX unit PCB (Part No. J72-0678-
02).  this silk screen will be
corrected from the next version, J72-0678-
12. 
						

							14
TK-860G/862G
REALIGNMENT
No. FunctionChoices Display Remarks
9 RF High power PWR_H___←Default
power Low power PWR_L___
10 Wide/ Wide WIDE____
Narrow Narrow NARROW__
11 Scan DELETE SCAN_DEL Not used for 8ch
Delete/AddADD SCAN_ADD←Default
12 Priority No P.CH_NO__ Not used when (Scan)
channel Yes P.CH_YES_ priority is not fixed
13 Home No H.CH_NO__ Not used when home
channel Yes H.CH_YES_ channel is not set in
key assignment
14
CompanderNo COMP_NO_ Not used when wide
is selected
Yes COMP_YES
15 PTT ID OFF P.ID_OFF_
Begin of TX P.ID_1___
End of TX P.ID_2___
Both P.ID_3___
16 Begin 000~ _BOT_ID_ Not valid if Dial ID=
of TX ID
9999999999999999disable and PTT ID=
off, or EOT is set
Display when an item
is selected (about
0.5 seconds)
12345678 Display of the current
setting (If it is 8 or
more digits, scroll it)
- - - - - 987 Display when a code
is input (Input it with
DTMF key)
Blank - - - - - - - - [] : Data clear
17 End of 000~ _EOT_ID_ Not valid of Dial ID=
TX ID
9999999999999999Idisable and PTT ID=
off, or BOT is set
Display when an item
is selected (about
0.5 seconds)
12345678 Display of the current
setting (If it is 8 or
more digits, scroll it)
- - - - - 987 Display when a code
is input (Input it with
DTMF key)
Blank - - - - - - - - [
] : Data clear
No. FunctionChoices Display Remarks
3 TX Step STP__250 Display when an item
frequency2.5kHz~1MHz STP_1000 is selected or when a
step is changed
(about 0.5 seconds)
[A] : Step change
2.5, 5.0, 6.25, 7.5kHz,
1MHz step
Blank - - - - - - - - [] : Frequency on/
100.0000~ T.100.0000 blank switching
550.0000MHz The rightmost dot
indicates 50Hz digit
(On=5, Off=0)
4 TX Off - - - - - - - - [] : Off/QT/DQT
signallingQT 67.0~250.3HzQT__67.0_ switching
(EIA mode) QT_250.3_ [A] : Mode switching
QT 67.0~250.3HzQT__67.0* [SCN] : Normal/
(0.1Hz step mode)QT_250.3* Inverse switching
DQT 000~777 DQT000N*
(Normal) DQT777N*
(1 step mode)
DQT 023~754 DQT023N_
(Normal) DQT754N_
(Standard table mode)
DQT 000~777 DQT000I*
(Inverse) DQT777I*
(1 step mode)
DQT 023~754 DQT023I_
(Inverse) DQT754I_
(Standard table mode)
5 Option Off NONE____←Default
signallingDTMF DTMF____
2-TONE 2TONE___
6 ID 000~ ___ID___ Display when an item
9999999999 is selected (about
0.5 seconds)
12345678 Display of the current
setting (If it is 8 or
more digits, scroll it)
- - - - - 987 Display when a code
is input (Input it with
DTMF key)
Blank - - - - - - - - [] : Data clear
7 Busy No BCL_NO__←Default
channel Type 1 BCL_1___ BCL_YES_ for K type
lockout Type 2 BCL_2___ Not used for K type
8 Beat No SHFT_NO_←Default
shift Yes SHFT_YES 
						

							15
TK-860G/862G
10. Function Setting Mode
All channels can be set up together in the action mode by
using the panel keys.
• Pressing [
] when SELF is displayed, sets the function
setting mode.
• Select an item set using [
] then change the selection
with the [CH
/].
• The data displayed using [D/A] is stored in the memory
and then proceeds to the next item.
• Pressing [
] proceeds to the next item without storing it
in the memory.
• Press [
] to display SELF and return to reset (default)
status.
No. FunctionChoices Display Remarks
Function key
1 [MON] Not function MON__OFF
(TK-860GVolume down MON___1_
only) Volume up MON___2_
Talk around MON___3_
Auxiliary MON___4_
Dispaly characterMON___5_
Home channel MON___7_
Channel down MON___8_
Channel up MON___9_
Key lock MON___10
Public address MON___12
Horn alert MON___14
Selectable QT MON___15 M destination only
2-tone encode MON___16
select
Monitor A MON___17←Default
Monitor B MON___18
Monitor C MON___19
Monitor D MON___20
Scan MON___22
Scan del/add MON___23
Group down MON___24
Group up MON___25
2 [A] No function KEY1_OFF←Default (TK-860G)
(TK-860G)Volume down KEY1__1_
[MON] Volume up KEY1__2_
(TK-862G)Talk around KEY1__3_
Auxiliary KEY1__4_
Dispaly characterKEY1__5_TK-862G cannot be selected
Home channel KEY1__7_
Channel down KEY1__8_
Channel up KEY1__9_
Key lock KEY1__10
Public address KEY1__12
REALIGNMENT
9-1. Flow Chart
Self programming
mode
[MON]
[MON]Channel setting
modeChannel selectionGroup selection
[D/A]
[   ]
OFFQT
OFF
[SCN]
[SCN]DQT NDQT I
[   ]
[MON]
[MON]
[MON]
[MON]
[MON]
[MON]
[MON]
RX frequency
[D/A]/[   ]
RX signalling
TX freuency
TX signalling
Option signalling
ID
Busy channel lockout
OFFQT
OFF
Data clear
DQT NDQT I
[D/A]/[   ]
[D/A]/[   ]
[D/A]/[   ]
[D/A]/[   ]
[D/A]/[   ]
[MON]Beat shift yes/no
[D/A]/[   ]
[MON]RF power high/low
[D/A]/[   ]
[MON]Wide/Narrow
[D/A]/[   ]
[MON]
Scan delete/add
[D/A]/[   ]
[MON]Priority channel Not used when (Scan) priority is not fixed.
Not used when home channel is not set 
in key assignment.
Not used when wide is selected.
[D/A]/[   ]
[MON]Home channel
[D/A]/[   ]
[MON]Compander yes/no
[D/A]/[   ]
[MON]PTT ID
[D/A]/[   ]
[MON]Begin of TX ID
[D/A]/[   ]
[MON]End of TX ID
[D/A]/[   ]
[D/A]/[   ]
[   ]
[   ]
[   ]
[   ]
[   ][   ]
[   ]
[   ]
[   ][   ]
Data clear[   ]
Data clear[   ] 
						

							16
TK-860G/862G
No. FunctionChoices Display Remarks
Horn alert KEY3__14
Selectable QT KEY3__15 M destination only
TK-862G cannot be selected
2-tone encode KEY3__16
select
Monitor A KEY3__17
Monitor B KEY3__18
Monitor C KEY3__19
Monitor D KEY3__20
Scan KEY3__22TK-862G cannot be selected
Scan del/add KEY3__23TK-862G cannot be selected
Group down KEY3__24TK-862G cannot be selected
Group up KEY3__25TK-862G cannot be selected
5[] No function KEY4_OFF←Default
(TK-860G)Volume down KEY4__1_
[A] Volume up KEY4__2_
(TK-862G)Talk around KEY4__3_
Auxiliary KEY4__4_
Dispaly characterKEY4__5_TK-862G cannot be selected
Home channel KEY4__7_
Channel down KEY4__8_
Channel up KEY4__9_
Key lock KEY4__10
Public address KEY4__12
Horn alert KEY4__14
Selectable QT KEY4__15 M destination only
TK-862G cannot be selected
2-tone encode KEY4__16
select
Monitor A KEY4__17
Monitor B KEY4__18
Monitor C KEY4__19
Monitor D KEY4__20
Scan KEY4__22TK-862G cannot be selected
Scan del/add KEY4__23TK-862G cannot be selected
Group down KEY4__24TK-862G cannot be selected
Group up KEY4__25TK-862G cannot be selected
6 [SCN] No function SCN__OFF←Default
(TK-860GVolume down SCN___1_
only) Volume up SCN___2_
Talk around SCN___3_
Auxiliary SCN___4_
Dispaly characterSCN___5_
Home channel SCN___7_
Channel down SCN___8_
Channel up SCN___9_
Key lock SCN___10
REALIGNMENT
No. FunctionChoices Display Remarks
Horn alert KEY1__14
Selectable QT KEY1__15 M destination only
2-tone encode KEY1__16
select
Monitor A KEY1__17←Default (TK-862G)
Monitor B KEY1__18
Monitor C KEY1__19
Monitor D KEY1__20
Scan KEY1__22TK-862G cannot be selected
Scan del/add KEY1__23TK-862G cannot be selected
Group down KEY1__24TK-862G cannot be selected
Group up KEY1__25TK-862G cannot be selected
3 [D/A] No function KEY2_OFF←Default
(TK-860G)Volume down KEY2__1_
[] Volume up KEY2__2_
(TK-862G)Talk around KEY2__3_
Auxiliary KEY2__4_
Dispaly characterKEY2__5_TK-862G cannot be selected
Home channelKEY2__7_
Channel downKEY2__8_
Channel up KEY2__9_
Key lock KEY2__10
Public addressKEY2__12
Horn alert KEY2__14
Selectable QT KEY2__15 M destination only
TK-862G cannot be selected
2-tone encode KEY2__16
select
Monitor A KEY2__17
Monitor B KEY2__18
Monitor C KEY2__19
Monitor D KEY2__20
Scan KEY2__22TK-862G cannot be selected
Scan del/add KEY2__23TK-862G cannot be selected
Group down KEY2__24TK-862G cannot be selected
Group up KEY2__25TK-862G cannot be selected
4[] No function KEY3_OFF←Default
(TK-860G)Volume down KEY3__1_
[] Volume up KEY3__2_
(TK-862G)Talk around KEY3__3_
Auxiliary KEY3__4_
Dispaly characterKEY3__5_TK-862G cannot be selected
Home channelKEY3__7_
Channel down KEY3__8_
Channel up KEY3__9_
Key lock KEY3__10
Public address KEY3__12 
						

							17
TK-860G/862G
No. FunctionChoices Display Remarks
Public addressCUP___12
Horn alert CUP___14
Selectable QT CUP___15 M destination only
TK-862G cannot be selected
2-tone encode CUP___16
select
Monitor A CUP___17
Monitor B CUP___18
Monitor C CUP___19
Monitor D CUP___20
Scan CUP___22TK-862G cannot be selected
Scan del/add CUP___23TK-862G cannot be selected
Group down CUP___24TK-862G cannot be selected
Group up CUP___25TK-862G cannot be selected
9 [CH] No function CDN__OFF
(ChannelVolume down CDN___1_
down) Volume up CDN___2_
Talk around CDN___3_
Auxiliary CDN___4_
Dispaly characterCDN___5_TK-862G cannot be selected
Home channelCDN___7_
Channel downCDN___8_←Default
Channel up CDN___9_
Key lock CDN___10
Public addressCDN___12
Horn alert CDN___14
Selectable QT CDN___15 M destination only
TK-862G cannot be selected
2-tone encode CDN___16
select
Monitor A CDN___17
Monitor B CDN___18
Monitor C CDN___19
Monitor D CDN___20
Scan CDN___22TK-862G cannot be selected
Scan del/add CDN___23TK-862G cannot be selected
Group down CDN___24TK-862G cannot be selected
Group up CDN___25TK-862G cannot be selected
10 [VOL] No function VUP__OFF
(VolumeVolume down VUP___1_
up) Volume up VUP___2_←Default
Talk around VUP___3_
Auxiliary VUP___4_
Dispaly characterVUP___5_TK-862G cannot be selected
Home channelVUP___7_
Channel downVUP___8_
Channel up VUP___9_
REALIGNMENT
No. FunctionChoices Display Remarks
Public address SCN___12
Horn alert SCN___14
Selectable QT SCN___15 M destination only
2-tone encode SCN___16
select
Monitor A SCN___17
Monitor B SCN___18
Monitor C SCN___19
Monitor D SCN___20
Scan SCN___22
Scan del/add SCN___23
Group down SCN___24
Group up SCN___25
7 [FOOT] No function FSW__OFF←Default
(FOOT Volume down FSW___1_
SW) Volume up FSW___2_
Talk around FSW___3_
Auxiliary FSW___4_
Dispaly characterFSW___5_
Emergency FSW___6_
Home channel FSW___7_
Channel down FSW___8_
Channel up FSW___9_
Key lock FSW___10
Public address FSW___12
Horn alert FSW___14
Selectable QT FSW___15 M destination only
2-tone encode FSW___16
select
Monitor A FSW___17
Monitor B FSW___18
Monitor C FSW___19
Monitor D FSW___20
Scan FSW___22
Scan del/add FSW___23
Group down FSW___24
Group up FSW___25
8 [CH] No function CUP__OFF
(ChannelVolume down CUP___1_
up) Volume up CUP___2_
Talk around CUP___3_
Auxiliary CUP___4_
Dispaly characterCUP___5_TK-862G cannot be selected
Home channelCUP___7_
Channel downCUP___8_
Channel up CUP___9_←Default
Key lock CUP___10 
						

							18
TK-860G/862G
No. FunctionChoices Display Remarks
15
Minimum0~31/1 step MVOL_12_
volume
16Off hookEnable H_D__ENA
decode Disable H_D__DIS←Default
17Off hookEnable H_H__ENA
horn alertDisable H_H__DIS←Default
18
Time outOFF, 15~600/ TOT_180_ Default : 180s
timer 15s step
19 TOT OFF, 1~10/ TOTP_OFF Cannot be set when
pre-alert1s step TOT is off
time Default : Off
20 TOT OFF, 1~60/ TOTK_OFF Cannot be set when
rekey 1s step TOT is off
time Default : Off
21 TOT OFF, 1~15/ TOTS_OFF Cannot be set when
reset 1s step TOT is off
time
22 Clear to YES CTT_YES_
transpondNO CTT_NO__←Default
(BCL for
transpond)
23SignallingOR SIG__OR_←Default
AND SIG__AND
24 Squelch 0~9/1 step SQL__5__ Default : 5
level
Scan
25 Priority None PRI_NONE Default : None
Fixed PRI_FIX_
Selected PRI_SEL_
26 Look 0.5~5.0/ LBA__500 Default : 500ms
back 0.05s Cannot be set when
time A Priority=none
27 Look 0.5~5.0/ LBB_2000 Default : 2000ms
back 0.05s Cannot be set when
time B Priority=none
28 Revert Selected REV_SEL_
channel Last called REV_L/C_←Default
Last used REV_L/U_
Selected+Talk backREV_S/T_
Priority REV_PRI_
Priority+Talk backREV_P/T_
29 Dropout 0~300/1s DODT___3 Default : 3s
delay time
30Dwell time0~300/1s DWL____3 Default : 3s
31Off hookEnable H_S__ENA
scan Disable H_S__DIS←Default
REALIGNMENT
No. FunctionChoices Display Remarks
Key lock VUP___10
Public addressVUP___12
Horn alert VUP___14
Selectable QTVUP___15 M destination only
TK-862G cannot be selected
2-tone encode VUP___16
select
Monitor A VUP___17
Monitor B VUP___18
Monitor C VUP___19
Monitor D VUP___20
Scan VUP___22TK-862G cannot be selected
Scan del/add VUP___23TK-862G cannot be selected
Group down VUP___24TK-862G cannot be selected
Group up VUP___25TK-862G cannot be selected
11 [VOL] No function VDN__OFF
(VolumeVolume down VDN___1_←Default
down) Volume up VDN___2_
Talk around VDN___3_
Auxiliary VDN___4_
Dispaly characterVDN___5_TK-862G cannot be selected
Home channelVDN___7_
Channel downVDN___8_
Channel up VDN___9_
Key lock VDN___10
Public addressVDN___12
Horn alert VDN___14
Selectable QTVDN___15 M destination only
TK-862G cannot be selected
2-tone encode VDN___16
select
Monitor A VDN___17
Monitor B VDN___18
Monitor C VDN___19
Monitor D VDN___20
Scan VDN___22TK-862G cannot be selected
Scan del/add VDN___23TK-862G cannot be selected
Group down VDN___24TK-862G cannot be selected
Group up VDN___25TK-862G cannot be selected
Optional feature
12 Power YES/NO PONT_YES Default : Yes
on tone
13 Control YES/NO CNTT_YES Default : Yes
tone
14 Warning YES/NO WART_YES Default : Yes
tone 
						

							19
TK-860G/862G
REALIGNMENT
Self programming
mode
Function setting
mode
[MON] key function[D/A]/[   ][A]/[MON] key function
[D/A]/[   ] key function
[   ]/[   ] key function
[   ]/[A] key function
[SCN] key function
[FOOT] key function
[D/A]/[   ]
[D/A]/[   ]
[D/A]/[   ]
[D/A]/[   ]
[D/A]/[   ]
[CH   ] key function
[D/A]/[   ]
[CH   ] key function
[D/A]/[   ]
[VOL   ] key function
[D/A]/[   ]
[VOL   ] key function
[D/A]/[   ]
Power on tone yes/no
[D/A]/[   ]
Control tone yes/no
[D/A]/[   ]
Warning tone yes/no
[D/A]/[   ]
Minimum volume
[D/A]/[   ]
Off hook decode
[D/A]/[   ]
Off hook horn alert
[D/A]/[   ]
[D/A]/[   ]
Time out timer
TOT pre-alert time
[D/A]/[   ]
TOT rekey time
[D/A]/[   ]
TOT reset time
[D/A]/[   ]
Clear to transpond
[D/A]/[   ]
Signalling
[D/A]/[   ]
[D/A]/[   ]
[   ][   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
Look back time A
Priority
Squelch level
[D/A]/[   ]
Look back time B
Revert channel
Dropout delay time
Dwell time
Off hook scan
Digit time
[D/A]/[   ]
[D/A]/[   ]
[D/A]/[   ]
[D/A]/[   ]
[D/A]/[   ]
[D/A]/[   ]
[D/A]/[   ]
Inter digit time
[D/A]/[   ]
First digit time
[D/A]/[   ]
First digit delay
[D/A]/[   ]
Rise time with QT
[D/A]/[   ]
Dial ID
[D/A]/[   ]
No. of DTMF key
[D/A]/[   ]
DTMF hold time
[D/A]/[   ]
Store & Send
[D/A]/[   ]
D key assignment
[D/A]/[   ]
DTMF signalling
[D/A]/[   ]
[D/A]/[   ]
Inter mediate code
Group code
[D/A]/[   ]
Auto reset time
[D/A]/[   ]
Call alert/Transpond
[D/A]/[   ]
Panel test/
Panel tuning mode[D/A]/[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
[   ]
No. FunctionChoices Display Remarks
DTMF
32Digit time50~200ms/10msDIGT__50 Default : 50ms
33
Inter digit50~1000ms/50msIDT___50 Default : 50ms
time
34
First digit50~200ms/10msFDT___50 Default : 50ms
time
35
First digit50~1000ms/50msRIST_100 Default : 100ms
delay
36
Rise time50~1000ms/50msRTWQ_100 Default : 100ms
with QT
37 Dial ID Enable DID__ENA
Disable DID__DIS←Default
38 No. of 12 key NODK_12_←Default
DTMF key16 key NODK_16_
39 DTMF ON DHT__ON_←Default
hold timeOFF DHT__OFF
40Store andEnable SAS__ENA
send Disable SAS__DIS←Default
41 D key D code DKA_D_CD←Default
assignment1~16s/1s DKA_16__
42 DTMF Code SQ DTMS_CSQ←Default
signallingSWL CALL DTMF_SEL TK-860G only
43 Inter 0~9, A~D, IMC__#__ Default : # (Can be
mediate *, # set only when DTMF
code signalling= SEL CALL)
44 Group A~D, *, # GPCD_OFF Default : OFF
code
45 Auto OFF ART__OFF
reset time1~15s/1s ART__10_ Default : 10s
46Call alertOFF CA/T_OFF←Default
/transpondCall alert CA/T_C/A
Transpond CA/T_T/A
(Call alert)
Transpond CA/T_T/I
(ID code)
Transpond CA/T_T/T
(Transpond code)
Others
47 Panel Enable PTM__ENA←Default
test/ Not used for TK-862G
panel Disable PTM__DIS
tuning
mode
10-1. Flow Chart
11. Memory Reset Mode (TK-860G only)
You can clear all settings you made in self programming
mode, or you can return to the original display.
• Press [SCN] while SELF is displayed will change the dis-
play to CANCEL.
• Press [CH
/] to change the display between CAN-
CEL and READY.
• When READY is displayed, pressing [SCN] will set all
data to default, and CLEAR will appear on the display.
Press [SCN] again to display SELF.
• When CANCEL is displayed, pressing [SCN] will cancel
the reset, and SELF will be displayed. 
						

							20
TK-860G/862G
34
5
6
7
89
1. Accessory Connection Cable
(KCT-19 : Option)
The KCT-19 is an accessory connection cable for con-
necting external equipment.  The connector has 15 pins and
the necessary signal lines are selected for use.
1-1. Installing the KCT-19 in the transceiver
1. Remove the upper and lower halves of the transceiver
case, and lift the DC cord bushing ( ) from the chassis.
2. Remove the pad as shown in Figure 1 ( ).
3. Insert the KCT-19 cable ( ) into the chassis ( ).
The wire harness band ( ) must be inside the chassis.
4. Replace the DC cord bushing ( ).
5. Connect the KCT-19 to the TX-RX unit (A/2) as shown in
Figure 2 ( ).
6. Connect the KCT-19 to the external accessory by insert-
ing the crimp terminal ( ) into the square plug ( ),
both of which are supplied with the KCT-19.
1
2
1
3
13
15
12
Crimp terminal
(E23-0613-05)
BE
C
B
D
CN8
CN5
D
E
B
C
A
Contact Square plug
(E09-1571-05)3 46
78 9
5
CN4
CN3
1
2
Fig. 1
Fig. 2
INSTALLATION
1-2. KCT-19 Accessory Port Function
No. No. Name FunctionNote
(A)(B,C,D,E)
1 D-2 RXD Serial control data input *1
DTC Data channel control/ *2
External hook input
2 D-5 ME External microphone ground
3 D-3 IGN Ignition sense input
4 D-1 DEO Receiver detector output
5 D-6 MI External microphone input
6 B-2 E Ground
7 B-3 SB Switched B+, DC 13.6V output.
Maximum 1A
8 D-7 PTT External PTT input *2
9 D-4 DI Data modulation input
10 B-1 HOR Horn alert/call output
11 D-8 SQ Squelch detect output Busy : H *2
12 C-1 SP Speaker audio output.
13 E-1 AMSpeaker mute input, active high
14 E-2 MM MIC mute input, active high
15 E-3 EMG Foot switch input, active low *3
TXS
Transmitter sense output, active high
*1 : SmarTrunk OMNI mode
*2 : MDT mode
*3 : Emergency mode