JVC Th V70r Instructions

18
3 Attach the board to the wall.
Anchor the board securely in at least four places to the supports inside the wall.
The diameter of the screws must be more than 4 mm, and their length must be 3 times the thickness of the board mounted
on the wall (also take the thickness of the wall into account ).
4 Mount three screws (not supplied) to the board which has been attached on the wall.
Use the screws as illustrated below.
You can use the supplied paper pattern to mark the positions where the screws are...

19
Getting Started
Using the remote control
The remote control makes it easy to use many of the functions of the system at a distance of up to 7 m (23 feet) away.
• You can also operate other components from the remote control supplied with this system.
– To operate your TV, see page 20.
– To operate your VCR, CATV convertor, or DBS tuner, see page 69.
Putting batteries in the remote control
Before using the remote control, put two supplied batteries first.
1 On the back of the remote control, remove the...

20
Using the remote control for TV operations
You can operate your TV using the remote control supplied with this system.
• Refer also to the instruction manuals supplied with your TV.
7Setting the remote control signal for operating your TV.
• You can operate your TV without setting the remote control signal if your TV is a
JVC TV.
1 Slide the remote control mode selector to ”AUDIO/TV/VCR.”
2 Press and hold TV 
.
• Keep it pressed until step 4 is finished.
3 Press TV CONTROL.
4 Press Number buttons...

21
Basic operations
This section mainly explains operations commonly used when you enjoy this system.
• This manual mainly explains operations when the center unit is placed vertically (the DISP.SET selector is set to “V”) as an example.
• Turn also on your TV and select the correct input mode on the TV.
IMPORTANT:
When using the remote control, check to see if its
remote control mode selector is set to the correct
position:
To operate this system, set it to “AUDIO/TV/VCR.”AUDIO/
TV/VCR
CATV/DBS
Turning...

22
To turn p ower off
F rom the  remote cont rol:  P ress AUDIO 
 again.
On the center unit:  Press 
 again.
The illumination lamps and the button name indications (except the 
 indicator) go o ff.
•  When placing the center unit verticall y,  the moving panel closes.
7  When the resume pl ayba ck is set to  “ ON ” (see p ag e 62):
If you tu rn o ff the power while playing back a disc, playback stops and the position w\
he re playback has been stopped is
sto red.
T o  resume playback f rom the sto red...

23
Turning off the sound temporarily
From the remote control ONLY:
Press MUTING.
“MUTING” appears on the display window and the volume turns off.
To restore the sound
Press MUTING again.
• Pressing VOLUME +/– (or VOL +/– on the center unit) also restores the sound.
Adjusting the brightness
You can dim the indications on the moving panel and the illumination lamps on the center unit.
From the remote control ONLY:
Press DIMMER.
Each time you press the button, the brightness level of the indications and the...

24
Turning off the power with the timer
Using the sleep timer, you can fall asleep while listening to music, and know the system will turn off by itself rather than play all
night.
From the remote control ONLY:
Press SLEEP.
Each time you press the button, the shut-off time changes as follows:
] 0min (cancelled) ] 10min (minutes) ] 20min ] 30min ] 60min ] 90min ] 120min ] 150min
] (back to the beginning)
To check the remaining time until the shut-off time
Press SLEEP once.
The remaining time until the...

25
Basic operations
Changing the decode mode
When you play a disc (or software) encoded with Dolby Digital or DTS Digital Surround, the following symptoms may occur:
• Sound does not come out at the beginning of playback.
• Noise comes out while searching for or skipping chapters or tracks.
In these cases, change the decode mode to “DOLBY D” (for Dolby Digital) or “DTS” (for DTS Digital Surround).
From the remote control ONLY:
Press DECODE to select the decode mode when DVD or AUX DIGITAL is selected as...

26
Changing the scan mode
This system supports the progressive scan system (480p*) as wel as the conventional interlaced scan system (480i*).
If your TV equipped with component jacks supports the progressive video input, you can enjoy a high quality picture by
making the progressive scan mode active.
• Refer also to the instruction manuals supplied with your TV.
• If your TV equipped with component jacks does not support the progressive video input, do not change the scan mode to
the progressive scan...

27
Inserting and removing a disc
IMPORTANT:
DO NOT insert a disc with your finger put in the hole of a disc.
1 When the center unit is placed horizontally, press 0.
The moving panel opens and the disc slot appears.
Basic playback
CHANNEL VOLUME TV VOL
TUNINGSTOP
DIMMERPAUSE
FF//REW
TV/VIDEO1MUTING¡
RECPLAYDOWN UP
MEMORY
STROBE
ENTER
ON
SCREEN
CHOICE
AUDIO/
TV/VCR
SURROUNDMODE
CATV/DBS
PAUSE button
SOURCEVOL
8 button This section explains basic operations for playback of DVDs, VCDs, SVCDs, and Audio CDs....