JVC R S11 Manual

ENGLISH
31REFERENCES
CD PLAYER SECTION 
Type: Compact disc player
Signal Detection System: Non-contact optical pickup 
(semiconductor laser)
Number of Channels: 2 channels (stereo)
Frequency Response: 5 Hz to 20 000 Hz
Dynamic Range: 96 dB
Signal-to-Noise Ratio: 98 dB
Wow and Flutter: Less than measurable limit
MP3 Decoding Format: (MPEG1/2 Audio Layer 3) Max. Bit Rate: 320 kbps
WMA (Windows Media® Audio) Decoding Format: Max. Bit Rate: 192 kbps
BLUETOOTH
Version: Bluetooth 1.2 certified
Power Class:...

EN, TH, RU
1107DTSMDTJEIN© 2007 Victor Company of Japan, Limited 
Having TROUBLE with operation?
Please reset your unit
Refer to page of How to reset your unit
Затруднения при эксплуатации?
Пожалуйста, перезагрузите Ваше устройство
Для получения информации о перезагрузке Вашего устройства 
обратитесь на соответствующую страницу
Rear_KD-BT11_001A_1.indd   2Rear_KD-BT11_001A_1.indd   210/31/07   5:41:21 PM10/31/07   5:41:21 PM 

1
KD-BT11
Installation/Connection Manual
°“√µ‘
¥µ—
È
ß/§Ÿ
Ë
¡◊
Õ°“√µ‘
¥µ—
È
ß
Руководство по установке/подключениюGET0507-004A
[U]
 ENGLISH
This unit is designed to operate on 12 V DC, NEGATIVE ground 
electrical systems. If your vehicle does not have this system, a 
voltage inverter is required, which can be purchased at JVC car audio 
dealers.
WARNINGS
To prevent short circuits, we recommend that you disconnect the 
battery’s negative terminal and make all electrical connections before 
installing the...

2
When using the optional stay / ‡¡◊
Ë
Õ„™È
µ—
«¬÷
¥·∫∫‡≈◊
Õ°‰¥È
 / 
При использовании дополнительной стойки 
Note :  When installing the unit on the mounting bracket, make sure to use the 8 mm-long screws. If longer screws 
are used, they could damage the unit.
À¡“¬‡Àµ : ‡¡◊
Ë
Õµ‘
¥µ—
È
ß™ÿ
¥ª√–°Õ∫≈ß„π·∑Ë
π√Õß√—
∫‰«È
 „ÀÈ
„™È °√Ÿ
¬“«¢π“¥ 8 ¡¡. ∂È
“„™È °√Ÿ
¬“«°«Ë
“π’
È
Õ“®∑”„ÀÈ
™ÿ
¥ª√–°Õ∫‡ ’
¬À“¬‰¥ôПримечание :  При установке устройства на крепежный кронштейн, используйте только винты длиной 8 мм. При...

3
A  Typical connections / °“√‡™◊
Ë
Õ¡µË
Õ·∫∫ª°µ / Типичные подключения 
Before connecting: Check the wiring in the vehicle carefully. 
Incorrect connection may cause serious damage to this unit.
The leads of the power cord and those of the connector from the car 
body may be different in color.
1  Connect the colored leads of the power cord in the order 
specified in the illustration below.
2  Connect the antenna cord.
3  Finally connect the wiring harness to the unit.
Line out (see diagram  )“¬ÕÕ° (¥Ÿ...

4
B  Connecting the external amplifier or subwoofer / °“√µË
Õ°—
∫·Õ¡a≈‘
ø“¬‡ÕÕ√Ï
·≈–´—
ø«Ÿ
ø‡«Õ√Ï
µ—
«πÕ° / 
Подключение внешних усилителей и низкочастотного динамика 
You can connect an amplifier to upgrade your car stereo system.
•  Connect the remote lead (blue with white stripe) to the remote 
lead of the other equipment so that it can be controlled through 
this unit.
•  Disconnect the speakers from this unit, connect them to the 
amplifier. Leave the speaker leads of this unit unused.
To the remote...

ENGLISH
 KD-BT11
CD RECEIVER  KD-BT11
  For canceling the display demonstration, see page 4.
For installation and connections, refer to the separate manual.
INSTRUCTIONS
GET0507-003A[UT]
Cover_KD-BT11_003A_f.indd   1Cover_KD-BT11_003A_f.indd   112/8/07   8:46:19 AM12/8/07   8:46:19 AM 

ENGLISH
2
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best 
possible performance from the unit.
IMPORTANT FOR LASER PRODUCTS
1.  CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to 
qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with...

ENGLISH
3
  How to reset your unit
• Your preset adjustments will also be erased (except the 
registered Bluetooth device, see pages 10 and 11).
  How to forcibly eject a disc
• Be careful not to drop the disc when it ejects.
• If this does not work, reset your unit.
  How to use the M MODE button
If you press M MODE, the unit goes into functions mode, 
then the number buttons and 
5/∞ buttons will work 
as different function buttons.
Ex.:  When number button 2 works as MO (monaural) 
button.
To use...

ENGLISH
4INTRODUCTIONS
Preparation
  Cancel the display demonstration and set the clock
•  See also page 20.
1Turn on the power.
2Enter the PSM settings.
3Cancel the display demonstrations
  Select “DEMO,” then “DEMO OFF.”
Set the clock
  Select “CLOCK HOUR,” then adjust the hour.
  Select “CLOCK MIN” (minute), then adjust the minute.
4Finish the procedure.
When the power is turned off: Check the current clock time
When the power is turned on: Change the display information of the current source...