JVC Projector DLA-RS400 User Manual

Main Unit - Rear
.I
Input terminals
In addition to the video input terminal, there are also
other connection terminals for devices such as
controllers and optional equipment.
Please see 
“Main Unit - Input Terminals”P. 12 for
more details about the terminals.
J Lamp cover
When replacing the light source lamp, remove this
cover.
K Operation panel
For more details, please refer to the “Operation
panel” in the diagram below. L
Remote Sensor (rear)
Please 
aim the remote control at this area when using
it.
*...

Main Unit - Input Terminals
. A
[HDMI 1] input terminal
B [HDMI 2] input terminal
For connecting to devices that support HDMI output.
(P. 
18)
It is fitted to the M3 lock hole. The depth of the screw
hole is 3 mm.
C [LAN] terminal (RJ-45)
The projector can be controlled by connecting it to a
PC through the computer network for control
commands to be sent to the projector.
D [RS-232C] terminal (D-sub 9-pin
male)
The projector can be controlled by connecting a PC to
this terminal.
E [3D SYNCHRO] terminal...

Remote Control
AB [STAND BY]
Turns off the power. (
P. 22)
B C [ON]
Turns on the power. (P. 21)
C [INPUT]
Select an input from [HDMI 1]
and [HDMI 2]. (P. 21)
D [INFO.]
Displays the information menu.
(P. 56)
E [MEMORY MENU]
Switches between saving,
retrieving, and editing of the lens
memory. (P. 24)
F [MEMORY 1]
Retrieves LENS MEMORY 1.
G [MEMORY 2]
Retrieves LENS MEMORY 2.
H [LENS CONTROL]
For adjusting focus, zoom, and
shift. (P. 23)
I [LENS AP.]
For setting the lens aperture.
(P. 40)
J [C.M.D.]
For...

Loading Batteries into the Remote Control
Loading the batteries
.Removing the batteries
. 0
If the remote control has to be brought closer to the
projector to operate, it means that the batteries are
wearing out. Replace the batteries with new ones
(AAA).
0 Insert the batteries according to the  t s marks.
Be sure to insert the s end first.
When removing the battery, do so from the t end.
0 If an error occurs while using the remote control,
remove the batteries and wait for five minutes. Load
the...

Installing the Projector
Precautions during Installation
Please read the following carefully before installing this
unit. Do not install at the following
This unit is a precision device. Please refrain from
installing  or using it at the following locations. Otherwise,
it may cause fire or malfunction.
0 Dusty, wet and humid places
0 Places subject to oily smoke or cigarette smoke
0 On top of a carpet or bedding, or other soft surfaces
0 Places exposed to direct sunlight
0 Places with a high or low...

Precautions during Mounting
Securing (mounting) the projector
. 0
When  this unit is to be mounted to a fixed position for
use, install it horizontally.
0 Make sure to secure the main unit to prevent
accidents such as during an earthquake.
Securing with screws
.Remove the four feet at the bottom, and fasten using the
screws (M5 screws, 13 to 23 mm).
* Using 

screws other than those designated may cause
the unit to break down.
* Leave a clearance of at least 10 mm from the bottom surface of the unit to...

Adjusting the Position
Adjusting the elevation angle of the projector
The height and inclination of the unit (0 to 5 mm) can be
adjusted by turning the feet.
Lift the unit and adjust the four feet.
. Adjusting the position of the image
By using the lens shift feature of this unit, you can shift
the image upward/downward or to the left/right. Set it to
your preferred position. Æ “Adjusting the Lens According to the Projection
Position” (P. 
23)
. 0
The maximum vertical shift varies with the amount of...

Connecting the Projector
0 Do not turn on the power until connection is complete.
0 The connection procedures differ according to the device used. For details, please refer to the instruction manual
of the device to be connected.
0 This projector is used for projecting images. To output the audio of connected devices, please connect a separate
audio output device, such as an amplifier or speaker.
0 The images may not be displayed depending on the devices and cables to be connected.
A high speed HDMI...

Connecting via HDMI-DVI conversion cable
. 0
If noise occurs, move the desktop PC away from this unit.
0 If the video is not displayed, try to reduce the length of the cable or lower the resolution of the video transmitting
equipment. Connecting to the LAN Terminal
. 0
The network is used to control this unit. It is not used for sending or receiving video signals.
0 Please contact your network administrator for information concerning the network connection.
0 Set “ECO Mode” to “Off” if LAN communication...

Connecting to the TRIGGER Terminal
. 0
Do not use it to supply power to other devices.
0 Connecting to the audio terminal of another device may cause the device to malfunction or break down.
0 Using beyond the rated value will cause the unit to malfunction.
0 The trigger terminal outputs a voltage of 12 V. Exercise adequate caution to prevent short circuit.
0 The factory setting is “Off”. To change the setting, configure the “Trigger” item in the menu ( P. 54).Connecting the Power Cord (Supplied...