JVC Kds6060 Instruction Manual

(No.MA028)1-11 3.2.3 Removing the DET switch  
(See Figs.6 and 7)
(1) Extend the two tabs c of the feed sw. holder and pull out
the switch.
(2) Unsolder the DET switch wire if necessary.
Fig.6
Fig.7
Connector 
boardDET switch
Pickup
DET switchTab c
Tab c
DET switch wire
Feed sw. holder 

1-12 (No.MA028) 3.2.4 Removing the chassis unit 
(See Figs.8 and 9)
• Prior to performing the following procedure, remove the top
cover and connector board.
(1) Remove the two suspension springs (L) and (R) attaching
the chassis unit to the frame.
CAUTION:
• The shape of the suspension spring (L) and (R) are dif-
ferent. Handle them with care.
• When reassembling, make sure that the three shafts
on the underside of the chassis unit are inserted to the
dampers certainly.
Fig.8
Fig.9
Suspension spring (L)...

(No.MA028)1-13 3.2.5 Removing the clamper assembly 
(See Figs.10 and 11)
• Prior to performing the following procedure, remove the top
cover.
(1) Remove the clamper arm spring.
(2) Move the clamper assembly in the direction of the arrow to
release the two joints d.
Fig.10
Fig.11
Clamper arm
 spring
Chassis rivet 
assembly
Joint d Joint d
Clamper assembly
Clamper arm spring
Clamper 
assembly
Joint d
Joint d
Chassis rivet assembly 

1-14 (No.MA028) 3.2.6 Removing the loading / feed motor assembly 
(See Figs.12 and 13)
• Prior to performing the following procedure, remove the top
cover, connector board and chassis unit.
(1) Remove the screw C  and move the loading / feed motor
assembly in the direction of the arrow to remove it from the
chassis rivet assembly.
(2) Disconnect the wire from the loading / feed motor assembly
if necessary.
CAUTION:
When reassembling, connect the wire from the loading /
feed motor assembly to the flame as...

(No.MA028)1-15 3.2.7 Removing the pickup unit 
(See Figs.14 to 18)
• Prior to performing the following procedure, remove the top
cover, connector board and chassis unit.
(1) Remove the screw D  and pull out the pu. shaft holder from
the pu. shaft.
(2) Remove the screw E  attaching the feed sw. holder.
(3) Move the part e of the pickup unit upward with the pu. shaft
and the feed sw. holder, then release the joint f of the feed
sw. holder in the direction of the arrow. The joint g of the
pickup unit and...

1-16 (No.MA028) 3.2.9 Removing the trigger arm 
(See Figs.19 and 20)
• Prior to performing the following procedure, remove the top
cover, connector board and clamper unit.
(1) Turn the trigger arm in the direction of the arrow to release
the joint k and pull out upward.
CAUTION:
When reassembling, insert the part m and n of the trigger
arm into the part p and q at the slot of the chassis rivet
assembly respectively and join the joint k at a time.
Fig.19
Fig.20
3.2.10 Removing the top plate assembly 
(See...

(No.MA028)1-17 3.2.11 Removing the mode sw. / select lock arm 
(See Figs.22 and 23)
• Prior to performing the following procedure, remove the top
plate assembly.
(1) Bring up the mode sw. to release from the link plate (joint t)
and turn in the direction of the arrow to release the joint u.
(2) Unsolder the wire of the mode sw. marked s if necessary.
(3) Turn the select lock arm in the direction of the arrow to re-
lease the two joints v.
(4) The select lock arm spring comes off the select lock arm at...

1-18 (No.MA028) 3.2.12 Reassembling the mode sw. / select lock arm 
(See Figs.24 to 26)
REFERENCE:
Reverse the above removing procedure.
(1) Reattach the select lock arm spring to the top plate and set
the shorter end of the select lock arm spring to the hook w
on the top plate.
(2) Set the other longer end of the select lock arm spring to the
boss x on the underside of the select lock arm, and join the
select lock arm to the slots (joint v). Turn the select lock
arm as shown in the figure.
(3) Reattach...

(No.MA028)1-19 3.2.13 Removing the select arm R / link plate 
(See Figs.27 and 28)
• Prior to performing the following procedure, remove the top
plate assembly.
(1) Bring up the select arm R to release from the link plate
(joint a) and turn as shown in the figure to release the two
joints b and joint c.
(2) Move the link plate in the direction of the arrow to release
the joint d. Remove the link plate spring at the same time.
REFERENCE:
Before removing the link plate, remove the mode sw..
Fig.27
Fig.28...

1-20 (No.MA028) 3.2.15 Removing the loading roller assembly 
(See Figs.31 to 33)
• Prior to performing the following procedure, remove the
clamper assembly and top plate assembly.
(1) Push inward the loading roller assembly on the gear side
and detach it upward from the slot of the joint g of the lock
arm rivet assembly.
(2) Detach the loading roller assembly from the slot of the joint
h of the lock arm rivet assembly.
The roller guide comes off the gear section of the loading
roller assembly.
Remove the...