JVC Kdg111 Instruction Manual
Have a look at the manual JVC Kdg111 Instruction Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 313 JVC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
11 ENGLISH Selecting the playback modes You can use only one of the following playback modes at a time. 1 2 Select your desired playback mode. Repeat play Ex.: When “TRK RPT” is selected Mode Plays repeatedly TRK RPT: The current track. RPT lights up. RPT OFF: Cancels repeat play. Random play Ex.: When “DISC RND” is selected Mode Plays at random DISC RND: All tracks of the current disc. RND lights up. RND OFF: Cancels random play. Prohibiting disc ejection You can lock a disc in the loading slot. To cancel the prohibition, repeat the same procedure. To check the current clock time while listening to a disc EN10-13_KD-G111[EX_EU]f.indd 1110/9/04, 1:18:52 PM
12 ENGLISH Sound adjustments Selecting preset sound modes (C-EQ: custom equalizer) You can select a preset sound mode suitable to the music genre. ~ Ex.: When “ROCK” is selected Indication pattern for each sound mode: Indication For:Preset values BAS*1TRE*2LOUD*3 USER (Flat sound) 00 00 OFF ROCK Rock or disco music+03 +01 ON CLASSIC Classical music+01–02 OFF POPS Light music +04 +01 OFF HIP HOP Funk or rap music+02 00 ON JAZZ Jazz music +02 +03 OFF * 1 BAS: Bass *2 TRE: Treble *3 LOUD: Loudness EN10-13_KD-G111[EX_EU]f.indd 1210/8/04, 12:15:20 PM
13 ENGLISH Adjusting the sound You can adjust the sound characteristics to your preference. 1 Ex.: When “TRE” is selected 2 Indication pattern changes as you adjust the level. Indication To do: Range BAS*1 (bass)Adjust the bass. –06 (min.) to +06 (max.) TRE* 1 (treble)Adjust the treble. –06 (min.) to +06 (max.) FAD* 2 (fader)Adjust the front and rear speaker balance.R06 (Rear only) to F06 (Front only) BAL (balance)Adjust the left and right speaker balance.L06 (Left only) to R06 (Right only) LOUD* 1 (loudness)Boost low and high frequencies to produce a well- balanced sound at low volume level.LOUD ON J LOUD OFF VOL*3 (volume)Adjust the volume.00 (min.) to 30 or 50 (max.)* 4 *1 When you adjust the bass, treble, or loudness, the adjustment you have made is stored for the currently selected sound mode (C-EQ) including “USER.” * 2 If you are using a two-speaker system, set the fader level to “00.” * 3 Normally the +/– buttons work as the volume control. So you do not have to select “VOL” to adjust the volume level. * 4 Depending on the amplifier gain control setting. (See page 14 for details.) EN10-13_KD-G111[EX_EU]f.indd 1310/9/04, 1:20:11 PM
14 ENGLISH Indications Selectable settings, [reference page] DEMO Display demonstrationDEMO ON: [Initial]; Display demonstration will be activated automatically if no operation is done for about 20 seconds, [7]. DEMO OFF: Cancels. CLOCK H Hour adjustment0 – 23, [7] [Initial: 0 (0:00)] CLOCK M Minute adjustment00 – 59, [7] [Initial: 00 (0:00)] AMP GAIN Amplifier gain controlYou can change the maximum volume level of this receiver. LOW PWR: VOL 00 – VOL 30 (Select this if the maximum power of the speaker is less than 45 W to prevent them from damaging the speaker.) HIGH PWR: [Initial]; VOL 00 – VOL 50 General settings — PSM Basic procedure You can change PSM (Preferred Setting Mode) items listed on the table that follows. 1 2 Select a PSM item. Ex.: When you select “AMP GAIN” 3 Adjust the PSM item selected. 4 Repeat steps 2 and 3 to adjust the other PSM items if necessary. 5 Finish the procedure. EN14-19_KD-G111[EX_EU]f.indd 1410/8/04, 12:15:40 PM
15 ENGLISH When detaching or attaching the control panel, be careful not to damage the connectors on the back of the control panel and on the panel holder. Detaching the control panel Before detaching the control panel, be sure to turn off the power. Attaching the control panel Detaching the control panel EN14-19_KD-G111[EX_EU]f.indd 1510/8/04, 12:15:41 PM
16 ENGLISH Maintenance How to clean the connectors Frequent detachment will deteriorate the connectors. To minimize this possibility, periodically wipe the connectors with a cotton swab or cloth moistened with alcohol, being careful not to damage the connectors. Connector Moisture condensation Moisture may condense on the lens inside the CD player in the following cases: After starting the heater in the car. If it becomes very humid inside the car. Should this occur, the CD player may malfunction. In this case, eject the disc and leave the receiver turned on for a few hours until the moisture evaporates. How to handle discs When removing a disc from its case, press down the center holder of the case and lift the disc out, holding it by the edges. Always hold the disc by the edges. Do not touch its recording surface. When storing a disc into its case, gently insert the disc around the center holder (with the printed surface facing up). Make sure to store discs into the cases after use. To keep discs clean A dirty disc may not play correctly. If a disc does become dirty, wipe it with a soft cloth in a straight line from center to edge. Do not use any solvent (for example, conventional record cleaner, spray, thinner, benzine, etc.) to clean discs. To play new discs New discs may have some rough spots around the inner and outer edges. If such a disc is used, this receiver may reject the disc. To remove these rough spots, rub the edges with a pencil or ball-point pen, etc. Center holder Wrap discSticker Sticker residue DiscStick-on label Do not use the following discs: EN14-19_KD-G111[EX_EU]f.indd 1610/8/04, 12:15:41 PM
17 ENGLISH More about this receiver Basic operations Turning off the power If you turn off the power while listening to a disc, disc play will start from where playback has been stopped previously, next time you turn on the power. Tuner operations Storing stations in memory During SSM search... – All previously stored stations are erased and stations are stored newly. – Received stations are preset in No. 1 (lowest frequency) to No. 6 (highest frequency). – When SSM is over, the station stored in No. 1 will be automatically tuned in. When storing a station manually, a previously preset station is erased when a new station is stored in the same preset number. Disc operations General This receiver has been designed to reproduce CDs, and CD-Rs (Recordable)/CD-RWs (Rewritable) in audio CD (CD-DA) format. When a disc has been loaded, selecting “CD” for the playback source starts disc play. Inserting a disc When a disc is inserted upside down, the disc automatically ejects. Do not insert 8 cm discs (single CD) and unusual shape discs (heart, flower, etc) into the loading slot. Playing a CD-R or CD-RW Use only “finalized” CD-Rs or CD-RWs. This receiver can play back multi-session discs; however, unclosed sessions will be skipped while playing. Some CD-Rs or CD-RWs may not play back on this receiver because of their disc characteristics, and for the following causes: – Discs are dirty or scratched. – Moisture condensation occurs on the lens inside the receiver. – The pickup lens inside the receiver is dirty. – CD-R or CD-RW on which the files are written with “Packet Write” method. – There are improper recording conditions (missing data, etc.) or media conditions (stain, scratch, warp, etc.). CD-RWs may require a longer readout time since the reflectance of CD-RWs is lower than that of regular CDs. Do not use the following CD-Rs or CD-RWs: – Discs with stickers, labels, or protective seal stuck to the surface. – Discs on which labels can be directly printed by an ink jet printer. Using these discs under high temperatures or high humidity may cause malfunctions or damage to discs. Changing the source If you change the source, playback also stops (without ejecting the disc). Next time you select “CD” for the playback source, disc play starts from where it has been stopped previously. Ejecting a disc If the ejected disc is not removed within 15 seconds, the disc is automatically inserted again into the loading slot to prevent it from dust. (Disc will not play this time.) General settings—PSM If you change the “AMP GAIN” setting from “HIGH PWR” to “LOW PWR” while the volume level is set higher than “VOL 30,” the receiver automatically changes the volume level to “VOL 30.” EN14-19_KD-G111[EX_EU]f.indd 1710/8/04, 12:15:41 PM
18 ENGLISHSymptoms Causes Remedies General Sound cannot be heard from the speakers.The volume level is set to the minimum level.Adjust it to the optimum level. Connections are incorrect. Check the cords and connections. The receiver does not work at all.The built-in microcomputer may have functioned incorrectly due to noise, etc.Reset the receiver (see page 2). FM/AM SSM automatic presetting does not work.Signals are too weak. Store stations manually. Static noise while listening to the radio.The aerial is not connected firmly.Connect the aerial firmly. Disc playback Disc automatically ejects. Disc is inserted upside down.Insert the disc correctly. CD-R/CD-RW cannot be played back. Tracks on the CD-R/ CD-RW cannot be skipped.CD-R/CD-RW is not finalized. Insert a finalized CD-R/ CD-RW. Finalize the CD-R/ CD-RW with the component which you used for recording. Disc can be neither played back nor ejected.Disc is locked. Unlock the disc (see page 11). The CD player may have functioned incorrectly.Eject the disc forcibly (see page 2). Disc sound is sometimes interrupted.You are driving on rough roads.Stop playback while driving on rough roads. Disc is scratched. Change the disc. Connections are incorrect. Check the cords and connections. “NO DISC” appears on the display.No disc in the loading slot. Insert a disc into the loading slot. Disc is inserted incorrectly. Insert the disc correctly. Troubleshooting What appears to be trouble is not always serious. Check the following points before calling a service center. EN14-19_KD-G111[EX_EU]f.indd 1810/9/04, 1:20:41 PM
19 ENGLISH Specifications AUDIO AMPLIFIER SECTION Maximum Power Output: Front: 45 W per channel Rear: 45 W per channel Continuous Power Output (RMS): Front: 17 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortion. Rear: 17 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than 0.8% total harmonic distortion. Load Impedance: 4 Ω (4 Ω to 8 Ω allowance) Tone Control Range: Bass: ±10 dB at 100 Hz Treble: ±10 dB at 10 kHz Frequency Response: 40 Hz to 20 000 Hz Signal-to-Noise Ratio: 70 dB Line-Out Level/Impedance: 2.0 V/20 kΩ load (full scale) Output Impedance: 1 kΩ TUNER SECTION Frequency Range: FM: 87.5 MHz to 108.0 MHz AM: (MW) 522 kHz to 1 620 kHz (LW) 144 kHz to 279 kHz [FM Tuner] Usable Sensitivity: 11.3 dBf (1.0 µV/75 Ω) 50 dB Quieting Sensitivity: 16.3 dBf (1.8 µV/75 Ω) Alternate Channel Selectivity (400 kHz): 65 dB Frequency Response: 40 Hz to 15 000 Hz Stereo Separation: 30 dB Capture Ratio: 1.5 dB [MW Tuner] Sensitivity: 20 µV Selectivity: 35 dB [LW Tuner] Sensitivity: 50 µV CD PLAYER SECTION Type: Compact disc player Signal Detection System: Non-contact optical pickup (semiconductor laser) Number of channels: 2 channels (stereo) Frequency Response: 5 Hz to 20 000 Hz Dynamic Range: 96 dB Signal-to-Noise Ratio: 98 dB Wow and Flutter: Less than measurable limit GENERAL Power Requirement: Operating Voltage: DC 14.4 V (11 V to 16 V allowance) Grounding System: Negative ground Allowable Operating Temperature: 0°C to +40°C Dimensions (W × H × D): Installation Size (approx.): 182 mm × 52 mm × 150 mm Panel Size (approx.): 188 mm × 58 mm × 11 mm Mass (approx.): 1.3 kg (excluding accessories) Design and specifications are subject to change without notice. EN14-19_KD-G111[EX_EU]f.indd 1910/14/04, 1:40:39 PM
2 DEUTSCH Wir danken Ihnen für den Kauf eines JVC Produkts. Bitte lesen Sie die Anleitung vollständig durch, bevor Sie das Gerät in Betrieb nehmen, um sicherzustellen, daß Sie alles vollständig verstehen und die bestmögliche Leistung des Geräts erhalten. WICHTIG FÜR LASER-PRODUKTE 1. LASER-PRODUKT DER KLASSE 1 2. ACHTUNG : Die obere Abdeckung nicht öffnen. Das Gerät enthält keine Teile, die vom Benutzer gewartet werden können. Wartungen nur von qualifiziertem Fachpersonal durchführen lassen. 3. ACHTUNG : Sichtbare und unsichtbare Laserstrahlung bei offenem Gerät und Defekt oder Umgehen der Verriegelung. Setzen Sie sich dem Strahl nicht direkt aus. 4. ANBRINGEN DES ETIKETTS: WARNHINWEIS-ETIKETT, AUSSEN AM GERÄT ANGEBRACHT. Warnung: Wenn Sie den Receiver beim Fahren bedienen müssen, dürfen Sie nicht den Blick von der Straße nehmen, da sonst die Gefahr von Verkehrsunfällen besteht. Zurücksetzen des Geräts Dadurch wird der Mikrocomputer zurückgesetzt. Ihre vorgegebenen Einstellungen werden ebenfalls gelöscht. Wenn eine Disk eingelegt ist, wird sie ausgeschoben. Achten Sie darauf, die Disk nicht fallenzulassen. Zwangsweises Ausschieben einer Disk Wenn eine Disk vom Receiver nicht erkannt wird oder nicht ausgeschoben kann, können Sie zwangsweisen Ausschub wie folgt ausführen. Wenn das nicht funktioniert, führen Sie einen Reset am Receiver aus. Achten Sie darauf, die ausgeschobene Disk nicht fallen zu lassen. Aus Sicherheitsgründen wird eine nummerierte ID-Karte mit diesem Receiver mitgeliefert, und die gleiche ID-Nummer ist auf dem Chassis des Receivers aufgedruckt. Die Karte muss an sicherer Stelle aufbewahrt werden, da sie den Behörden bei der Identifikation des Receivers im Falle eines Diebstahls helfen kann. GE02-05_KD-G111[EY]f.indd 214/10/04, 11:30:26 PM