JVC Gd F65l1 Instructions

							
E
ENGLISH

29

RS-232C command table
How to read the command tableCommand:  Command field (See page 25.)
Direction:  W  When the “Parameter” is set in the parameter field (see page 25), the command functions as described 
under “Control/Response Contents”.
  R  The returned value indicated under “Reply” can be obtained by setting “????”, “
?” or “???+” 
(repeater control) in the parameter field (see page 25).
Parameter:  Parameter field (See page 25.)
Reply:  Response (Returned value)
*:  “Yes” indicates commands which can be used in power standby mode.
Power control/Input mode selection
FunctionCommandDirectionParameterReplyControl/Response contents*
POWER CONTROLPOWRW0 Switches to standby mode.
Yes
1Returns from standby mode.
R0Standby mode
1Normal mode
2Input signal waiting mode
INPUT MODE SELECTION
INPSW0 Toggle change for input mode
Terminals not selected in DVI SELECT/BNC SELECT cannot be 
selected.
Yes
1PC1 DIGITAL
“ERR” when AV (DIGITAL) is selected for DVI SELECT.
2PC2 ANALOG
3AV2 COMPONENT 
“ERR” when PC (ANALOG) is selected for BNC SELECT.
4 AV3 VIDEO
6PC3 ANALOG 
“ERR” when AV (COMPONENT) is selected for BNC SELECT.
7 AV1 DIGITAL 
“ERR” when PC (DIGITAL) is selected for DVI SELECT.
R1 PC1 DIGITAL
2PC2 ANALOG
3AV2 COMPONENT
4AV3 VIDEO
6PC3 ANALOG
7AV1 DIGITAL
SCREEN menu (PC2/PC3)
FunctionCommandDirectionParameterReplyControl/Response contents*
AUTO
ASNCW1No
CLOCKCLCKWR0-2550-255
No
PHASEPHSEWR0-630-63
POSITIONINGPOSITION OF 
THE LONGEST 
DIRECTION
HPOSWR0-5000-500 A maximum value depends on a resolution.
POSITION OF 
THE SHORTEST 
DIRECTION
VPOSWR0-1000-100
RESETARSTW1No
Controlling the Monitor with a PC
 
						

							
E
30

PICTURE menu
FunctionCommandDirectionParameterReplyControl/Response contents*
AUTO
AGINW1When the input mode is PC2, PC3.No
CONTRASTCONTWR0-600-600-127 on PC2/PC3.
Yes
BLACK LEVELBLVLWR0-600-600-127 on PC2/PC3.
TINTTINTWR0-600-60When the input mode is AV.
COLORSCOLRWR0-600-60
SHARPNESSSHRPWR0-240-24
ADVANCED FLESH TONE
FLESWR0-20-20: OFF, 1: LOW, 2: HIGH
Yes
3D-NRTDNRWR0-20-20: OFF, 1: LOW, 2: HIGH
MPEG-NRMPNRWR0-10-10: OFF, 1: ON
3D-Y/CYCSPWR0-10-10: OFF, 1: ON
COLOR MODEBMODWR00STD
Yes
22VIVID
33sRGB (When the input mode is PC)
WHITE BALANCETHRUCTMPWR00When the input mode is PC1.
Yes
PRESET1-151-15From 1: approximately 3,000K to 15: approximately 10,000K(500K steps)
USER9999
R-CONTRASTCRTRWR0-5120-512“ERR” when CTMP is not set to 99.
G-CONTRAST CRTGWR0-5120-512
B-CONTRASTCRTBWR0-5120-512
GAMMAGAMMWR0-20-20: 1.8, 1: 2.2, 2: 2.4 Yes
RESETARSTW2No
AUDIO menu
FunctionCommandDirectionParameterReplyControl/Response contents*
TREBLEAUTRWR-10-10-10-10
YesBASSAUBSWR-10-10-10-10
BALANCEAUBLWR-10-10-10-10
RESETARSTW3No
SETUP menu
FunctionCommandDirectionParameterReplyControl/Response contents*
LANGUAGELANGWR1414ENGLISH
Yes
11DEUTSCH
22FRANÇAIS
33ITALIANO
44ESPAÑOL
55РУССКИЙ
66 
ID NUMBERID NO. SETTINGIDSTW0-255 Sets the monitor’s ID number. (“0” means “no ID number”.)
Yes
R0-255Returns the monitor’s ID number.
ID NO. SETTING (ONCE)IDSLW1-255 Sets a monitor ID number.
This ID number is only effective for the command immediately after this 
command. Yes
0Clears the ID number if one has been designated.
ID NO. SETTING (SUBSEQUENT)IDLKW1-255
Sets a monitor ID number. 
This ID number is effective for the next and all subsequent commands 
after this command. Yes
0Clears the ID number if one has been designated.
ID CHECKIDCKW0
ID  : xxx 
IDLK  : yyy Displays monitor’s own ID number and the selected ID number on the screen.
Yes
PICTURE FLIPPFILWR0-30-3
0: OFF, 1: MIRROR, 2: UPSIDE DOWN, 3: ROTATE Yes
Power On DelayPWODWR00OFF
Yes
1-601-60ON
Controlling the Monitor with a PC
 
						

							
E
ENGLISH

31

OPTION menu
FunctionCommandDirectionParameterReplyControl/Response contents*
DATE/TIME SETTING DATE
WRAABBCCDDEEAABBCCDDEEAA: Year, BB: Month, CC: Day, DD: Time, EE: Minute
Yes
SCHEDULESC01-SC08WRABCDEFFGGHABCDEFFGGHSchedule of a specified number
A: Schedule  0 = Not effective, 1 = Effective
B: Power  0 = OFF, 1 = ON
C: Day of the week 1  0 = Only once, 1 = Every week, 2 = Every day
D: Day of the week 2  0 = Sunday, 1 = Monday through 6 = Saturday, 
9 = Not exist
E: Day of the week 3  0 = Sunday, 1 = Monday through 6 = Saturday, 
9 = Not exist
F: Time  00-23
G: Minute  00-59
H: Input  0 = Not specified, 1 = PC1/AV1, 2 = PC2,
 
3 = PC3/AV2, 4 = AV3 Yes
DVI SELECTDVSLWR0-10-1
0: PC (DIGITAL), 1: AV (DIGITAL) Yes
BNC SELECTBNSLWR0-10-10: PC (ANALOG), 1: AV (COMPONENT) Yes
QUICK SHOOT (PC)
QSPCWR0-10-1 0: OFF, 1: ON Yes
QUICK SHOOT (AV) QSAV
WR0-10-10: OFF, 1: ON Yes
COLOR SYSTEMCSYSWR0-50-50: AUTO, 1: PAL, 2: PAL-60, 3: SECAM, 4: NTSC3.58, 5: NTSC4.43 Yes
AUDIO OUTPUTAOUTWR0-10-10: VARIABLE, 1: FIXED Yes
INPUT 
RESOLUTION (PC)
RESOLUTION CHECKPXCKR- Returns current resolution in the form of hhh, vvv.
No
PIXEL SETTING (PC2, PC3)PXSLWR11
V: 768) 1360 x 768
22V: 768) 1280 x 768
33V: 768) 1024 x 768
55V: 480) 848 x 480
66V: 480) 640 x 480
INPUT 
RESOLUTION 
(AV)RESOLUTION CHECKRESOR-480i, 480p, 1080i, 720p, 1080p, VGA, etc.No
SELF ADJUST
AADJWR0-10-1 0: OFF, 1: ON Yes
POWER MANAGEMENTPMNGWR0-10-10: OFF, 1: ON Yes
ENLARGE menu (When the input mode is PC)
FunctionCommandDirectionParameterReplyControl/Response contents*
ENLARGE MODEEMAGWR0-40-40: OFF, 1: 2 x 2, 2: 3 x 3, 3: 4 x 4, 4: 5 x 5
No
BEZEL WIDTH
WIDTH OF THE 
SHORTER SIDE
BEZHWR0-1000-100
WIDTH OF THE 
LONGER SIDEBEZVWR0-1000-100
IMAGE POSITION (2 x 2)EPOSWR0-30-3See page 21.
IMAGE POSITION (3 x 3)EPOSWR0-80-8
IMAGE POSITION (4 x 4)EPOSWR0-150-15
IMAGE POSITION (5 x 5)EPOSWR0-240-24
ENLARGEDSCREENPOSITIONING
THE LONGESTDIRECTIONEPSHWR-999-999-999-999The setting range depends on the ENLARGE MODE setting and theIMAGE POSITION.
THE SHORTEST
DIRECTIONEPSVWR-999-999-999-999
ENLARGE/IMAGE POSITION SETTINGESTGWRXXYYXXYY XX: Enlarge mode (Same as EMAG), YY: Image Position (Same as EPOS)
PIP/PbyP menu
FunctionCommandDirectionParameterReplyControl/Response contents*
PIP MODES
MWINWR0-30-3 0: OFF, 1: PIP, 2: PbyP, 3: PbyP2 Yes
PIP SIZE
MPSZWR1-121-12 Yes
PIP POS THE LONGEST 
DIRECTIONMHPSW0-100 Yes
R0-100Yes
THE SHORTEST 
DIRECTIONMVPSW0-100 Yes
R0-100Yes
PIP V/H-POS
MPOSW0-100,0-100Specify the position in MPOSxxxyyy format. (xxx: Longer side, yyy: Shorter side position) Yes
R0-100,0-100Returns a response in (xxx,yyy) format. (xxx: Longer side, yyy: Shorter side position)Yes
PIP BLEND
MWBLWR0-150-15 Yes
PIP SOURCE
MWIPWR11 PC1 DIGITAL
Yes
22PC2 ANALOG
33AV2 COMPONENT
44AV3 VIDEO
66PC3 ANALOG
77AV1 DIGITAL
SOUND CHANGE MWADWR1-21-21: MAIN, 2: SUB Yes
MAIN POS (Main screen)MWPPWR0-10-10: POS1, 1: POS2Yes
PbyP2 POS (Sub screen)MW2PWR0-20-20: POS1, 1: POS2, 2: POS3Yes
AUTO OFF
MOFFWR0-10-1 0: MANUAL, 1: AUTO Yes
Controlling the Monitor with a PC
 
						

							
E
32
Initialisation/Functional Restriction Setting (FUNCTION) menu
FunctioCommandDirectionParameterReplyControl/Response contents*
ALL RESET
RSETW0No
ADJUSTMENT LOCK
ALCKWR0-20-20: OFF Yes
OSD DISPLAY
LOSDWR0-10-10: ON, 1: OFF Yes
LEDOFLDWR0-10-10: ON, 1: OFFYes
Others
FunctionCommandDirectionParameterReplyControl/Response contents*
SCREEN SIZE (PC)WIDEWR1-51-51: WIDE, 2: NORMAL, 3: DotbyDot, 4: ZOOM1, 5: ZOOM2Yes
SCREEN SIZE (AV)
WIDEWR1-51-51: WIDE, 2: ZOOM1, 3: ZOOM2, 4: NORMAL, 5: DotbyDot Yes
VOLUMEVOLMWR0-310-31 Yes
MUTEMUTEWR0-10-10: OFF, 1: ONNo
INFORMATION
MODELINF1R Value
Yes
SERIAL NO
SRNOR Value
BRIGHTVLMPWR0-310-31Brightness Yes
TEMPERATURE SENSOR DSTA
R0Internal temperature normal
Yes
1Internal temperature abnormal (Standby mode)
2Internal temperature abnormal (Temperature is normal now, but it was abnormal during operation.)
3Internal temperature abnormal (Brightness of the backlight decreases.)
4Temperature sensor abnormal
TEMPERATURE ACQUISITION ERRT
R ValueTemperature at temperature sensors 1 through 3 are returned in the following forms:[Sensor 1], [Sensor 2], [Sensor 3] Yes
CAUSE OF LAST STANDBY MODE
STCAW0Initialisation
Yes
R0No detectable error has occurred
1Standby mode by POWER button
2Main power “OFF” by the main power switch
3Standby mode by RS-232C
4Waiting mode by No Signal (Incl: VESA DPMS/DMPM)
6Standby mode by abnormal temperature
8Standby mode by SCHEDULE setting
Controlling the Monitor with a PC
 
						

							
33E
ENGLISH
Troubleshooting
Before calling for repair services, make sure following checks 
for possible remedies to the encountered symptoms.
There is no picture or sound.•  Is the power cord disconnected? (See page 12.)
•   Is the main power switch set to “OFF”? (See page 14.)
•   Is the monitor in standby mode (the power LED illuminating 
in orange)? (See page 14.)
•   Make sure correct input mode is selected. (See page 15.)
•   If any external equipment is connected, make sure the 
equipment is operating (playing back).
Remote control does not work. •  Are the batteries inserted with polarity (+,-) aligned? (See 
page 12.)
•   Are the batteries exhausted? (See page 12.)
•   Point the remote control unit toward the monitor’s remote 
control sensor. (See page 12.)
•   Is the menu display hidden or is operation disabled? (See 
page 24.)
Sound from left and right speakers is reversed.
Sound is heard from only one side. •  Are audio cables connected properly? (See pages 10 and  11.)
•  Make sure audio cables for external speakers are 
connected properly: left and right cables may be reversed 
or one of the two cables may not be connected. (See page 
11.)
•  Check the setting of BALANCE for AUDIO menu. (See 
page 18.)
There is a picture but no sound. •  Is the sound muted?
•  Make sure the volume is not set to minimum.
•  Is the PC audio cable (commercially available) connected?
•  Are audio cables connected properly?
•  Is the audio signal input properly to the audio input terminal 
corresponding to the selected video input terminal?
Unstable video.•  The signal may be incompatible.
•  Try the automatic screen adjustment when the PC2 input 
terminal or PC3 input terminals is used.
PC1 or AV1 does not appear properly. •  Is the setting of DVI SELECT correct? (See page 19.)
•  Is the input signal compatible with this monitor? (See pages 
10 and 35.)
•  Turn off the power to the connected equipment and then 
turn the power on again.
•  If the monitors are connected in a daisy chain, turn off the 
power to all the monitors connected in a daisy chain and 
then turn the power on again.
PC3 or AV2 does not appear properly. •  Is the setting of BNC SELECT correct? (See page 19.)
•  Is the input signal compatible with this monitor? (See page 
35.)
Control buttons do not work.
There is no picture.•  Some kind of load noises from outside might interfere with  normal operation. Turn off the power and turn it on after 
waiting at least 5 seconds, and then check the operation. Power LED flashes red.
“SERVICE CALL” appears in the corner of the screen.
•   Hardware has a problem. Turn off the monitor and request  repair from your JVC dealer.
When “TEMPERATURE” is displayed. •   When the internal temperature of the monitor rises  excessively, the brightness of the backlight decreases 
in order to prevent high-temperature-related problems. 
Remove the cause of the excessive rise in temperature. 
(See the description below.)
The monitor sometimes makes a cracking sound.•   You may hear cracking sound from the monitor. This 
happens when the cabinet slightly expands and contracts 
according to change in temperature. This does not affect 
the monitor’s performance.
■ Warning when temperature rises
•   When the internal temperature of the monitor rises  excessively, the brightness of the backlight decreases 
automatically in order to prevent high-temperature-
related problems. When this occurs, “TEMPERATURE” is 
displayed on the screen and the Power LED flashes red 
and green alternately.
•   If the internal temperature rises further, the monitor 
automatically enters standby mode. (The Power LED 
continues flashing red and green alternately.) 
Solution: •   If the monitor enters standby mode due to a rise in  temperature, to return to normal display, turn the main 
power switch off and then back on again. The monitor, 
however, will enter standby mode again if the cause of the 
temperature rise is not eliminated. (See page 9.)
•   Check whether the monitor is placed at a location where a  quick rise in temperature is likely. Internal temperature rises 
quickly if the vents on the monitor are blocked.
•   Internal temperature rises quickly if dust accumulates inside 
the monitor or around the vents. Remove dust if possible. 
Ask JVC dealer about removing internal dust.
 
						

							
34E
Specifications
Product Specifications
Model GD-F65L1
LCD element 65" wide (163.9 cm diagonal) 
ASV low-reflection black TFT LCD
Max. resolution (pixels) 1920 x 1080
Max. colours 16.77 M colours (8 bits/colour)
Pixel pitch 0.744 mm (H) x 0.744 mm (V)
Vi
ewing angle   176° right/left/up/down (contrast ratio ≥ 10)
Screen active area (mm) 1428 x 804
Computer input signal  Digital (DVI 1.0 standard-compliant),  Analogue RGB (0.7 Vp-p) [75 Ω]
 Sync signal Horizontal/vertical separate (TTL: positive/negative), Sync-on-green, 
    Composite sync (TTL: positive/negative)
Vi
deo colour system  PAL, PAL-60, SECAM, NTSC (3.58 MHz), NTSC (4.43 MHz)
Plug and play  VESA DDC2B
Power management VESA DPMS, DVI DMPM
Input terminals  PC/AV Digital  DVI-D 24 pin (HDCP  compatible) x 1
   
PC Analogue  Mini D-sub 15 pin, 3 rows x 1, BNC *1*2 x 1
   
 Audio  3.5 mm mini stereo jack x 1
    AV
 Composite video  BNC x 1
   
 Component  BNC (Y, Cb/Pb, Cr/Pr)*1 x 1
   
 Audio RCA pin (L/R) x 1
   
Serial (RS-232C)  D-sub 9 pin x 1
Output terminals  PC/AV Digital  DVI-D 24 pin x 1 *3
  Audio     RCA pin (L/R) x 1
   
Serial (RS-232C)  D-sub 9 pin x 1
   
Speaker      7 W + 7 W [6 Ω]
Power requirement AC 100 V - 240 V, 50/60 Hz
Operating temperature 0°C to 40°C
Operating humidity 20% to 80% (no condensation)
Power consumption  550 W (Input signal waiting mode: 10  W, Standby mode: 4.0 W)
Dimensions (mm) Approx. 1,572 x 126 x 923 (excluding protrusions)
We
ight  (kg)  Approx. 65 (excluding the temporary stand)
*1  Cannot be used simultaneously.
*2  Does not support plug and play.
*3  Connection is allowed with an HDCP-compatible device only. Does not support Repeater control function.
Design and specifications are subject to change without notice.
 
						

							
E
ENGLISH

35
Compatible signal timing (PC)
VESA
Wide
US TEXT
Sun
Screen resolutionHsyncVsyncDot frequencyAnalogue signal
640 x 480
800 x 600
848 x 480
1024 x 768
11
52 x 864
1280 x 768
1280 x 960
1280 x 1024
1360 x 768
1600 x 1200*1
1280 x 720
1920 x 1080
720 x 400
1024 x 768
11
52 x 900
1280 x 1024
1600 x 1000
31.5 kHz
37.9 kHz
37.5 kHz
35.1 kHz
37.9 kHz
48.1 kHz
46.9 kHz
31.0 kHz
48.4 kHz
56.5 kHz
60.0 kHz
67.5 kHz
47.8 kHz
60.3 kHz
60.0 kHz
64.0 kHz
80.0 kHz
47.7 kHz
75.0 kHz
44.7 kHz
66.3 kHz
31.5 kHz
48.3 kHz
53.6 kHz
56.6 kHz
61.8 kHz
71.8 kHz
71.7 kHz
81.1 kHz
68.6 kHz 60 Hz
72 Hz
75 Hz
56 Hz
60 Hz
72 Hz
75 Hz
60 Hz
60 Hz
70 Hz
75 Hz
75 Hz
60 Hz
75 Hz
60 Hz
60 Hz
75 Hz
60 Hz
60 Hz
60 Hz
60 Hz
70 Hz
60 Hz
66 Hz
70 Hz
66 Hz
76.2 Hz
67.2 Hz 76 Hz
66 Hz 25.175 MHz
31.5 MHz
31.5 MHz
36.0 MHz
40.0 MHz
50.0 MHz
49.5 MHz
33.75 MHz
65.0 MHz
75.0 MHz
78.75 MHz
108.0 MHz 79.5 MHz
102.25 MHz 108.0 MHz
108.0 MHz
135.0 MHz
85.5 MHz
162.0 MHz 74.4 MHz
148.5 MHz 28.3 MHz
64.13 MHz 70.4 MHz
74.25 MHz
94.88 MHz
108.23 MHz
117.01 MHz
134.99 MHz
135.76 MHz Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Digital signal
Yes
Ye
s
Ye
s
-
Yes
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
Ye
s
-
-
-
-
-
-
-
-
*1  Displays a reduced image.
*  All are compliant only with non-interlaced.
*  Depending on the connected PC, images may not be displayed properly even if the compatible signal described above is input.
*  The frequency values for the Sun are reference values.
Specifications
Dimensional Drawings
Note that the values shown are approximate values.
20Opening height (807)
Opening width (1432)
Unit: mm1572
126
71485
860
20
923
8585
650
440
393
Screw holes for mounting brackets (M10 x 4 holes)
595155
  When mounting the monitor, read the manual of the brackets or stand for their mounting procedure. The screw holes for  mounting brackets (M10 x 4 holes) are provided on the rear of the monitor .
  Note that screw hole depth of the monitor is 20 mm. Loose holding may cause the product to fall, resulting in serious personal 
injuries as well as damage to the product. The screw and hole should come together with over 10 mm length of thread. Use 
the bracket which can endure at least 4 times or more the weight of the monitor .
 
						

							
E
36
PC1/AV1 input terminal pins
(DVI-D24 pin)
 
No.
1
2
3
4
5
6
7
8
9
10
11
12
Function
TMDS data 2-
TMDS data 2+
TMDS data 2/4 shield
N.C.
N.C.
DDC clock
DDC data
N.C.
TMDS data 1-
TMDS data 1+
TMDS data 1/3 shield
N.C.
No.
13
14
15
16
17
18
19
20
21
22
23
24
Function
N.C.
+5 V
GND
Hot-plug detection
TMDS data 0-
TMDS data 0+
TMDS data 0/5 shield
N.C.
N.C.
TMDS clock shield
TMDS clock+
TMDS clock-
RS-232C input terminal pins
(D-sub 9 pin)
 
No.
1
2
3
4
5
Function
N.C.
Transmitted data
Received data
N.C.
GND
No.
6
7
8
9
Function
N.C.
N.C.
N.C.
N.C.
RS-232C output terminal pins
(D-sub 9 pin)
 
No.
1
2
3
4
5
Function
N.C.
Received data
Transmitted data
N.C.
GND
No.
6
7
8
9
Function
N.C.
N.C.
N.C.
N.C.
PC2 input terminal pins
(Mini D-sub 15 pin)
 
No.
1
2
3
4
5
6
7
8
Function
Red video signal input
Green video signal input
Blue video signal input
N.C.
GND
GND for red video signal
GND for green video signal
GND for blue video signal
No.
9
10
11
12
13
14
15
Function
+5 V
GND
N.C.
DDC data
Hsync signal input
Vsync signal input
DDC clock
PC/AV output terminal pins
(DVI-D24 pin)
 
No.
1
2
3
4
5
6
7
8
9
10
11
12
Function
TMDS data 2-
TMDS data 2+
TMDS data 2/4 shield
N.C.
N.C.
DDC clock
DDC data
N.C.
TMDS data 1-
TMDS data 1+
TMDS data 1/3 shield
N.C.
No.
13
14
15
16
17
18
19
20
21
22
23
24
Function
N.C.
+5 V
GND
Hot-plug detection
TMDS data 0-
TMDS data 0+
TMDS data 0/5 shield
N.C.
N.C.
TMDS clock shield
TMDS clock+
TMDS clock-
Specifications
Power management
This monitor conforms to VESA DPMS and DVI DMPM. Both your video card and computer must support the same standard in 
order for the monitor’s power management function to work.
DPMS
ON ST
ATE
STANDBY
SUSPEND
OFF ST ATE
Screen
Display
No display
Power
consumption
550 W
10 W
Hsync
Ye
s
No
Ye
s
No
Vsync
Ye
s
Ye
s
No
No
DMPM
Monitor ON
Active OFF
Screen
Display
No display
Power consumption
550 W
10 W
DPMS: Display Power Management SignalingDMPM: Digital Monitor Power Management
DDC (plug and play)
The monitor supports the VESA DDC (Display Data Channel) standard.
DDC is a signal standard for plug and play between monitors and computers. Information about resolution and other parameters 
is exchanged between the two. This function can be used if the computer supports DDC and it has been configured to detect 
plug-and-play monitors.
There are several types of DDC, depending on the communication method used.  This monitor supports DDC2B.
 
						

							0508STH-MW-SH
© 2008 Victor Company of Japan, Limited08E DSC1
TINSM1116MPZA(1)
G D-F 65L1_co ve r.in dd   2GD-F65L1_cover.indd   24 /2 3/2 008   6 :2 6:4 5 P M4/23/2008   6:26:45 PM