JVC Gd F65l1 Instructions

							
9E
ENGLISH
How to Install the Monitor
Mounting precautions
•  Since the monitor is heavy, consult your dealer before installing, removing or moving the monitor.
•  When installing, removing or moving the monitor, ensure 
that this is carried out by at least 2 people.
•  Consult your dealer about the recommended wall mounting  unit for the monitor.
•  When moving the monitor, be sure to hold it with the 
handles both on the rear and the unit bottom. Do not hold 
the LCD panel. This may cause product damage, failure, or 
injury.
•  Install the monitor with the surface perpendicular to a  level surface. If necessary, limit the tilt between 0 and 20 
degrees downward.
•  Mounting the monitor on the wall requires special expertise  and the work must be performed by a qualified technician. 
You should never attempt to perform any of this work 
yourself. Our company will bear no responsibility for 
accidents or injuries caused by improper mounting or 
mishandling.
•  This monitor should be used at an ambient temperature 
between 0°C and 40°C. Provide enough space around the 
monitor to prevent heat from accumulating inside.
Unit: cm
3.5
5 5
5
30
  If it is difficult to provide such space because the monitor is 
installed inside a housing or for other reasons, take other 
measures to keep the ambient temperature between  
0°C and 40°C such as installing a fan in the housing.
•  Do not block any ventilation openings. If the temperature 
inside the monitor rises, this could lead to a malfunction.
•  After mounting, it is recommended to take some measures 
to prevent the monitor from falling down. Secure the 
monitor by fastening the hooks at the top of the monitor to a 
wall or a pillar with strong cord and brackets (not included).
•  Do not place the monitor on a device which generates heat.
•   This monitor is fixed to the temporary stand when shipped 
from the factory. Please note that this stand is for temporary 
use only until the monitor is properly mounted.
•  Be sure to use a stand or a wall-mount bracket designed or  designated for mounting the monitor.
•  This monitor is designed to be installed on a concrete wall  or pillar. Reinforced work might be necessary for some 
materials such as plaster / thin plastic board / wood before 
starting installation. 
This monitor and bracket must be installed on a wall which 
can endure at least 4 times or more the weight of the 
monitor. Install by the most suitable method for the material 
and the structure.
 
						

							
10E
Connecting Peripheral Equipment
Caution
•  Be sure to turn off the main power switch and disconnect 
the plug from the power outlet before connecting/
disconnecting cables. Also, read the manual of the 
equipment to be connected.
•  Be careful not to mix up the input terminal with the output 
terminal when connecting cables. Mixing up the input and 
output terminals may cause malfunctions and the other 
problems.
Connection with a PC
PC1 input terminal
PC audio input terminalPC2 input terminal
PC3 input terminals
HV
R G
B
•  Use a commercially available signal cable (DVI-D 24  pin) for the PC1 input terminal. Set DVI SELECT on the 
OPTION menu to PC (DIGITAL) when using the PC1 input 
terminal. (See page 19.)
•  Use a commercially available signal cable (Mini D-sub 
15 pin) for the PC2 input terminal.
•  Use a commercially available signal cable (BNC) for the  PC3 input terminals. Set BNC SELECT on the OPTION 
menu to PC (ANALOG) when using the PC3 input 
terminals. (See page 19.)
•  Use a commercially available audio cable (mini stereo jack) 
for the PC audio input terminal. Use an audio cable without 
resistance.
TIPS
•  Images may not be displayed properly depending on the 
computer (graphics board) to be connected.
•  A screen with 1920 x 1080 resolution may not be displayed 
correctly on PC3 (BNC). In this case, check the settings of 
your computer (graphics board) to verify that input signals 
conform to specifications of this monitor (Hsync: 66.3 kHz, 
Vsync: 60 Hz, and Dot frequency: 148.5 MHz). (See page 
35.)
•  If there is a check box to disable EDID in display control 
panel, check it when using PC3 (BNC).
•  Use the automatic screen adjustment when a PC screen is  displayed for the first time using PC2 or PC3, or when the 
setting of the PC is changed. (See page 23.)
•  The screen is adjusted automatically when SELF ADJUST 
in the OPTION menu is set to “ON”. (See page 19.)
Connection with AV equipment
AV1 input terminal
AV audio input terminals
AV2 input terminals
AV3 input terminal
Cr/PrYCb/Pb
•  Use a commercially available signal cable (DVI-D 24 pin)  for the AV1 input terminal. Set DVI SELECT on the OPTION 
menu to AV (DIGITAL) when using the AV1 input terminal. 
(See page 19.)
•  Use a commercially available component cable (BNC) for  the AV2 input terminals. Set BNC SELECT on the OPTION 
menu to AV (COMPONENT) when using the AV2 input 
terminals. (See page 19.)
•  Use a commercially available video cable (BNC) for the  AV3 input terminal.
•  Use a commercially available audio cable (RCA) for the AV 
audio input terminals.
•  The AV1 input terminal is compatible with the video signals 
below:   1920  x  1080 p  @ 50/59.94/60 Hz
  1920  x  1080 i  @ 50/59.94/60 Hz
  1280  x   720 p  @ 50/59.94/60 Hz
  720  x  576 p  @ 50 Hz
  720  x  480 p  @ 59.94/60 Hz
  640  x  480 p  @ 59.94/60 Hz
•  The AV2 input terminals are compatible with the video 
signals below: 1080i (1125i)/50, 1080i (1125i)/60, 720p (750p)/50, 
720p (750p)/60, 576p (625p), 576i (625i), 480p (525p), 
480i (525i)
 
						

							
E
ENGLISH

11
Connecting Peripheral Equipment
Other terminals
PC/AV audio output terminals•  Audio from the equipment connected to the AV audio input 
terminals or PC audio input terminal is output. Connect to 
the audio input terminals of the connected equipment using 
a commercially available audio cable (RCA).
•  The audio output varies depending on the input mode 
selection. (See page 15.)
•  The volume level can be adjusted using the volume 
adjustment. (See page 15.)
•  Selecting FIXED of “AUDIO OUTPUT” from the OPTION  menu fixes the volume of sound output from the audio 
output terminals. (See page 19.)
•  Audio signals output from the PC/AV audio output terminals  cannot be adjusted using the AUDIO menu.
PC/AV output terminals 
Video signals from PC1 and AV1 can be output to
 
HDCP-compatible external device. Use this terminal when 
you connect multiple monitors in a daisy chain via DVI cable 
(commercially available). (See the description on the right.)
Images cannot be output to device that is not 
HDCP-compatible.
RS-232C input/output terminals
You can control the monitor from a PC by connecting a 
commercially available RS-232 straight cable between this 
terminal and the PC. (See page 25.)
Connecting external speakers
Be sure to use external speakers with an impedance of 6 Ω 
and a rated input of at least 7 W.
(1)(2)
1. While pushing the tab, insert the tip of the cable.
2. Release the tab.
TIPS
•  Be sure to connect the + and - terminals and the left and  right speakers properly.
•  Avoid short circuiting the + and - terminals.
Connecting multiple monitors
You can connect multiple monitors (up to 5 monitors) in a 
daisy chain by using the PC1/AV1 input terminals and PC/AV 
output terminals of this monitor.
Connection example
shows the signal flow
PC/AV output terminalPC1/AV1 input terminals
Digital signal (DVI) cables (commercially available)
To PC digital RGB output terminal
First monitorSecond monitor
TIPS
•  The length of the signal cables or surrounding environment  may affect the image quality.
•  The screen may not display properly when using terminals 
other than PC1/AV1 for the input mode. In this case, turn 
off the power to all the monitors connected in a daisy chain 
and then turn the power on again.
 
						

							
12E

Installing the batteries
1.  Press the cover gently and slide it in the direction of the arrow.
2.  See the instructions in the compartment and put in the supplied batteries (2 AA/R6 batteries) with their plus (+) 
and minus (-) sides oriented correctly.
3.  Close the cover.
TIPS
•  The supplied batteries (2 AA/R6 batteries) may become 
exhausted faster depending on the storage condition. It is 
recommended that you replace them with new batteries 
(commercially available) earlier than specified.
•  If you will not use the remote control for a long time, 
remove the batteries.
•   Use manganese or alkaline batteries only.
Remote control operation range
The operation range of the remote control unit is approx. 5 m 
at an angle of approx 10° from the centre to the top/bottom/
right/left of the remote control sensor.
10°
5 m
5 m
5 m
Remote control sensor
10°
TIPS
•  Do not expose the remote control unit to shock by dropping  or stepping on it. This could lead to a malfunction.
•  Do not expose the remote control unit to liquids, and do not 
place it in an area with high humidity.
•   The remote control unit may not work properly if the remote 
control sensor is under direct sunlight or strong lighting.
•   Objects between the remote control unit and the remote 
control sensor may prevent proper operation.
•   Replace the batteries when they run low as this may  shorten the remote control’s operation range.
•   If a fluorescent light is illuminated near the remote control 
unit, it may interfere with proper operation.
•   Do not use it with the remote control of other equipment  such as air conditioner, stereo components, etc.
Preparing the Remote Control Unit
Connecting the Power Cord
Caution
•  Do not use a power cord other than the one supplied with the monitor.
1. Turn off the main power switch.
2. Plug the power cord (supplied) into the AC input terminal.
3. Plug the power cord (supplied) into the AC power outlet.
AC input terminal
2
1
Main power switch
For power outlet
Power cord (Supplied)
3
 
						

							
13E
ENGLISH

Removing the Temporary Stand
Prepare wall-hanging brackets or a stand to mount the monitor unit. Read the manual for the brackets or stand for the proper 
mounting procedure. (The screw holes for mounting brackets (M10 x 4 holes) are provided on the rear of the monitor.)
Caution
•  The monitor is heavy. It must be handled by 2 or more people.
•  This monitor is fixed to the temporary stand when shipped from the factory. Please note that this stand is for temporary use 
only until the monitor is properly mounted.
1.  Hold the monitor with the handles to prevent it  from falling down, and remove the stand fixing 
screws (4).
2.  Lift the monitor by holding it with the handles and 
the underside of the unit.
3.  When the installation is complete, attach the 
included stand hole protection covers, using the 
supplied screws.
(1)  Fold the sheet perpendicularly with the 
adhesive side inward.
(2)  Remove the adhesive cover and attach the  sheet to the monitor.
• The temporary stand is specifically designed for this monitor. Do not use for other devices.
(Rear view)
 
						

							
14E

Turning Power On/Off
Caution
•  Turn on the monitor first before turning on the PC or 
playback device.
Turning on the main power
Main power switch
When the main power switch is off, the monitor cannot be 
turned on using the POWER button on the remote control unit.
Turning power on/off
Press the POWER button to turn the power ON/OFF.
INPUT
Power LED
Status of a power LEDStatus of the monitor
Green lightingPower “On”
Orange lightingPower “Off” (Standby mode)
Green flashing
Input signal standby mode 
(input using a PC)
Caution
•  When switching the main power switch or the POWER  button off and back on, always wait for at least 5 seconds. 
A short interval may result in a malfunction.
TIPS
•  If the monitor is in the input signal standby mode and you 
press the POWER button on the remote control unit, the 
monitor enters standby mode.
•  You can turn on/off the monitor by pressing the power  switch of the monitor.
•  Setting the SCHEDULE flashes the power LED alternately 
in red and orange in standby mode.
Date/time setting
•  If the time has yet to be set when the monitor is first turned 
on, the date/time setting screen appears. Set the date and 
time.
DA TE/TIME SETTING
SET
CANCEL
07
/ /
OK···[MENU]2001/01/0000:
:   :
1.  Press  ,  ,  or  to select the date and 
time, and press  or  to change the numerical 
values. 
2.  Select SET and then press
 MENU .
• Be sure to set the date and time.
•  The date/time setting screen will close automatically if no 
operation is performed for about 15 seconds. The date 
and time can be set using DATE/TIME SETTING from 
the OPTION menu when the date/time setting screen 
disappears.
TIPS
• Set the date in “Year/Month/Day” order.
• Set the time on a 24-hour basis.
• The clock stops after the power-off status continues for 
approximately 1 week.* The date/time setting screen 
appears at power-on. Be sure to set the date and time. 
(*  This is a guide. The power-off status that stops the clock 
depends on the status of the monitor.)
Disabling power on/off operations
Power on/power off operations can be disabled in order to 
protect the monitor from an accidental power off. Set the 
ADJUSTMENT LOCK in FUNCTION menu to “2”. (See page 
24.)
 
						

							
15E
ENGLISH

Basic Operation
1
23
4
5
67
8
1. INPUT (Input mode selection)
The menu is displayed. Press  or  to select the input 
mode, and press  to enter.
*  You can select the input terminal by pressing the input 
switch of the monitor.
Input mode VideoAudio
PC1 DIGITAL
*1PC1 input terminalPC audio input 
terminal
PC2 ANALOGPC2 input terminal
PC3 ANALOG
*2PC3 input terminals
AV1 DIGITAL
*1AV1 input terminal AV audio input 
terminals
AV2 COMPONENT*2AV2 input terminals
AV3 VIDEO AV3 input terminal
*1  Select the terminal for DVI SELECT. (See page 19.)
*2  Select the terminal for BNC SELECT. (See page 19.)
2. MUTE
Turns off the volume temporarily.
Press the MUTE button again to turn the sound back to the 
previous level.
3. MENU
Displays and turns off the menu screen (see page 17).
4. VOL +/- (Volume adjustment)
Pressing  or  displays the VOLUME menu when the menu screen is not displayed.
V O L U M E15
Press  or  to adjust the volume of the sound.
*  If you do not press any buttons for about 4 seconds, the 
VOLUME menu automatically disappears.
5. BRIGHT +/- (Backlight adjustment)
Pressing  or  displays the BRIGHT menu when the menu screen is not displayed.
B R I G H T15
Press  or  to adjust the brightness.
*  If you do not press any buttons for about 4 seconds, the 
BRIGHT menu automatically disappears.
6. SIZE (Screen size selection)
The menu is displayed.
Press  or  to select the screen size. (See page 16.)
7. DISPLAY
Displays monitor information. The display disappears when 
this button is pressed again or disappears automatically after 
approximately 15 seconds.
INPUT MODE 
SIZE 
COLOR MODE 
BRIGHT 
VOLUME 
ID No. 
MODEL 
S/N 
PC2 ANALOG
WIDE
STD
15
15
0
GD-F65L1
: 
: 
: 
: 
: 
: 
: 
: 
1 0 2 4 x 7 6 8 
INFORMATION  XXXX/XX/XX XXX     XX:XX:XX 
V: 60 Hz    H: 48.4 kHz 
8. MODE (Colour mode selection)
Each time you press this button, the colour mode changes in 
the following order:
STD (Standard) → VIVID → sRGB → STD...
•  sRGB applies to PC input only.
  sRGB is international standard of colour representation  specified by IEC (International Electrotechnical 
Commission). Colour conversion is made in taking account 
of liquid crystal’s characteristics and represents colour tone 
close to its original image.
 
						

							
E
16
Basic Operation
Switching the screen size
Even when the screen size is changed, the display may remain the same depending on the input signal.
WIDEPC inputDisplays image so it fills the entire screen.
AV input An image with a 4:3 aspect ratio is stretched to fill the entire screen.
ZOOM 1PC inputAn image with a 4:3 aspect ratio is enlarged to fill the entire screen 
without changing the aspect ratio. The edges of the image may be 
cut off.
AV input
ZOOM 2PC input Use this size if ZOOM 1 cuts off the subtitles.
AV input
NORMALPC input Displays image so it fills the screen without changing the aspect 
ratio of the input signals.
AV input
Displays the entire image of the aspect ratio of 4:3 without changing 
the aspect ratio.
DotbyDotPC inputDisplays the dots of the signals input from the connected PC as the 
corresponding dots on the screen. *
AV input
Displays the dots of the input signals as the corresponding dots on 
the screen.
*:  With a monitor with a screen resolution of 1600 x 1200, selecting DotbyDot displays the NORMAL screen.
TIPS
•  Using this monitor’s screen-size switching or dual-screen display functions to compress or expand the screen for commercial 
or public viewing in establishments like cafes or hotels may infringe on the rights of the creators, as protected by Copyright 
Law, so please be careful.
•  When “Enlarge” is set, the screen size is fixed to “WIDE” mode.
•  When dual-screen display is selected, the screen size cannot be changed.
•  The appearance of the original video may change if you select a screen size with a different aspect ratio than the original  image (e.g. TV broadcast or video input from external equipment). 
•  When an ordinary non-wide image (4:3) is viewed with the whole screen using the screen-size switching function of this 
monitor, the edge of the image may be lost or appear distorted. If you wish to respect the creator’s intentions, set the screen 
size to “NORMAL”.
•  When playing commercial software, parts of the image (like subtitles) may be cropped. In this case select the optimal screen  size using the screen-size switching function of this monitor. With some software, there may be noise or distortion at the 
edges of the screen. This is due to the characteristics of the software, and is not a malfunction.
•  Depending on the original image size, black bands may remain at the edges of the screen.
 
						

							
17E
ENGLISH
Menu Items
Displaying the menu screen
Video and audio adjustment and settings of various functions 
are enabled. This section describes how to use the menu 
items. See pages 18 to 20 for details of each menu items.
Example of operation
(Adjusting CONTRAST in the PICTURE menu)
1.  Press MENU to display the menu screen.
1 0 2 4 x 7 6 8V: 60 Hz    H: 48.4 kHz
AUTO
CLOCK
PHASE
H-PO
SV -POS
RESET
SCREEN
PICTURE
AUDIO
SETUP
OPTION
ENLARGE
PIP/PbyP
1273115031
SCREENPC2 ANALOG1/1
END···[MENU]
2.  Press  or  to select PICTURE, and press .
PICTURE menu is displayed.
3.  Press 
 or   to select CONTRAST.
AUTO
CONTRAST
BLACK LEVEL
SHARPNESS
30
96
12
PC2 ANALOG1/2PICTURESCREEN
PICTURE
AUDIO
SETUP
OPTION
ENLARGE
PIP/PbyP
OK···[MENU]
1 0 2 4 x 7 6 8 V: 60 Hz    H: 48.4 kHz
4.  Press  or  to adjust the setting.
AUTO
CONTRAST
BLACK LEVEL
SHARPNESS
40
96
12
PC2 ANALOG1/2PICTURESCREEN
PICTURE
AUDIO
SETUP
OPTION
ENLARGE
PIP/PbyP
OK···[MENU]
1 0 2 4 x 7 6 8 V: 60 Hz    H: 48.4 kHz
For items that have  , press , make settings and then 
press MENU.
5.  Press 
MENU twice to close the menu screen.
TIPS
•  The menu will differ depending on the input mode.
•  The menu screen will close automatically if no operation is  performed for about 15 seconds. (DATE/TIME SETTING 
and SCHEDULE screens will close in about 4 minutes.)
Menu screen display
AUTO
CONTRAST
BLACK LEVEL
SHARPNESS
30
96
12
PC2 ANALOG1/2PICTURESCREEN
PICTURE
AUDIO
SETUP
OPTION
ENLARGE
PIP/PbyP
OK···[MENU]
1 0 2 4 x 7 6 8 V: 60 Hz    H: 48.4 kHz
4132
1  Name of the menu
2  Input mode
3  An item being selected (highlighted)
4  Screen resolution of input signal, and other data.
TIPS
•  Items that cannot be selected appear in grey. 
(e.g. Function not supported by the current input signal)
 
						

							
E
18

Menu item details
The menu will differ depending on the input mode.
SCREEN (PC2/PC3)
AUTO
The CLOCK, PHASE, H-POS, and V-POS are automatically 
adjusted.
Pressing  performs adjustment.
Use this automatic adjustment when you use the PC2 input 
terminal or PC3 input terminals to display a PC screen for 
the first time or when you change the setting of the PC. (See 
page 23.)
CLOCK
Adjusts frequency for sampling clock for applicable video.
Adjust when there is flickering in the form of vertical stripes.
PHASE
Adjusts sampling clock phase for applicable video.
Useful when small characters appear with low contrast and/
or there are flickers at corners.*  Adjustments to PHASE should be made only after CLOCK 
has been correctly set.
H-POS
Adjust the horizontal position of the image.
V-POS
Adjust the vertical position of the image.
RESET
Resets the values of the SCREEN menu items to the factory 
preset values.
Select “ON” and then press MENU.
PICTURE
AUTO (PC2/PC3)
The CONTRAST and BLACK LEVEL are automatically 
adjusted.
Pressing  performs adjustment.
CONTRAST
Adjusts the brightness of the image.
BLACK LEVEL
Adjusts the entire brightness of the video signals.
TINT (AV input)
Adjusts the hue. Selecting + changes the colour towards 
green, and selecting - changes it towards magenta.
COLORS (AV input)
Adjusts the colour intensity.
SHARPNESS
Adjusts the sharpness of the image.
ADVANCED (AV input)
You can adjust more specifically. (See page 22.)
COLOR MODE
Changes the colour mode on the screen. The colour mode 
on the screen can also be changed using a remote control 
unit. (See page 15.)
*  sRGB is PC input only. See page 15 for details.
WHITE BALANCE
THRU ..............Displays the input signal level as is. 
(for PC1 only)
PRESET  .........Selects the colour temperature using 
PRESET.
USER  .............. Used for adjusting R-CONTRAST, 
G-CONTRAST, and B-CONTRAST 
respectively.
PRESET
Selects the colour temperature when the WHITE BALANCE 
is set to PRESET.
R-CONTRAST
Adjusts red component when the WHITE BALANCE is set to  
USER.
G-CONTRAST
Adjusts green component when the WHITE BALANCE is set 
to USER.
B-CONTRAST
Adjusts blue component when the WHITE BALANCE is set 
to USER.
COPY TO USER
Copies the value set for PRESET to the USER setting.
Select “ON” and then press MENU.
GAMMA
Select a gamma value.
RESET
Resets the values of the PICTURE menu items to the factory 
preset values.
Select “ON” and then press MENU.
AUDIO
TREBLE
Adjusts the volume of treble-level sound.
BASS
Adjusts the volume of bass-level sound.
BALANCE
Adjusts the balance of the audio sound between right and left.
RESET
Resets the values of the AUDIO menu items to the factory preset values.
Select “ON” and then press MENU.
SETUP
OSD H-POSITION
Adjusts the horizontal display position of menu screen.
Menu Items