JVC Gd F65l1 Instructions

9E
ENGLISH
How to Install the Monitor
Mounting precautions
•  Since the monitor is heavy, consult your dealer before installing, removing or moving the monitor.
•  When installing, removing or moving the monitor, ensure 
that this is carried out by at least 2 people.
•  Consult your dealer about the recommended wall mounting  unit for the monitor.
•  When moving the monitor, be sure to hold it with the 
handles both on the rear and the unit bottom. Do not hold 
the LCD panel. This may cause product...

10E
Connecting Peripheral Equipment
Caution
•  Be sure to turn off the main power switch and disconnect 
the plug from the power outlet before connecting/
disconnecting cables. Also, read the manual of the 
equipment to be connected.
•  Be careful not to mix up the input terminal with the output 
terminal when connecting cables. Mixing up the input and 
output terminals may cause malfunctions and the other 
problems.
Connection with a PC
PC1 input terminal
PC audio input terminalPC2 input terminal
PC3...

E
ENGLISH

11
Connecting Peripheral Equipment
Other terminals
PC/AV audio output terminals•  Audio from the equipment connected to the AV audio input 
terminals or PC audio input terminal is output. Connect to 
the audio input terminals of the connected equipment using 
a commercially available audio cable (RCA).
•  The audio output varies depending on the input mode 
selection. (See page 15.)
•  The volume level can be adjusted using the volume 
adjustment. (See page 15.)
•  Selecting FIXED of “AUDIO...

12E

Installing the batteries
1.  Press the cover gently and slide it in the direction of the arrow.
2.  See the instructions in the compartment and put in the supplied batteries (2 AA/R6 batteries) with their plus (+) 
and minus (-) sides oriented correctly.
3.  Close the cover.
TIPS
•  The supplied batteries (2 AA/R6 batteries) may become 
exhausted faster depending on the storage condition. It is 
recommended that you replace them with new batteries 
(commercially available) earlier than specified.
•...

13E
ENGLISH

Removing the Temporary Stand
Prepare wall-hanging brackets or a stand to mount the monitor unit. Read the manual for the brackets or stand for the proper 
mounting procedure. (The screw holes for mounting brackets (M10 x 4 holes) are provided on the rear of the monitor.)
Caution
•  The monitor is heavy. It must be handled by 2 or more people.
•  This monitor is fixed to the temporary stand when shipped from the factory. Please note that this stand is for temporary use 
only until the monitor...

14E

Turning Power On/Off
Caution
•  Turn on the monitor first before turning on the PC or 
playback device.
Turning on the main power
Main power switch
When the main power switch is off, the monitor cannot be 
turned on using the POWER button on the remote control unit.
Turning power on/off
Press the POWER button to turn the power ON/OFF.
INPUT
Power LED
Status of a power LEDStatus of the monitor
Green lightingPower “On”
Orange lightingPower “Off” (Standby mode)
Green flashing
Input signal standby mode...

15E
ENGLISH

Basic Operation
1
23
4
5
67
8
1. INPUT (Input mode selection)
The menu is displayed. Press  or  to select the input 
mode, and press  to enter.
*  You can select the input terminal by pressing the input 
switch of the monitor.
Input mode VideoAudio
PC1 DIGITAL
*1PC1 input terminalPC audio input 
terminal
PC2 ANALOGPC2 input terminal
PC3 ANALOG
*2PC3 input terminals
AV1 DIGITAL
*1AV1 input terminal AV audio input 
terminals
AV2 COMPONENT*2AV2 input terminals
AV3 VIDEO AV3 input terminal
*1...

E
16
Basic Operation
Switching the screen size
Even when the screen size is changed, the display may remain the same depending on the input signal.
WIDEPC inputDisplays image so it fills the entire screen.
AV input An image with a 4:3 aspect ratio is stretched to fill the entire screen.
ZOOM 1PC inputAn image with a 4:3 aspect ratio is enlarged to fill the entire screen 
without changing the aspect ratio. The edges of the image may be 
cut off.
AV input
ZOOM 2PC input Use this size if ZOOM 1 cuts off the...

17E
ENGLISH
Menu Items
Displaying the menu screen
Video and audio adjustment and settings of various functions 
are enabled. This section describes how to use the menu 
items. See pages 18 to 20 for details of each menu items.
Example of operation
(Adjusting CONTRAST in the PICTURE menu)
1.  Press MENU to display the menu screen.
1 0 2 4 x 7 6 8V: 60 Hz    H: 48.4 kHz
AUTO
CLOCK
PHASE
H-PO
SV -POS
RESET
SCREEN
PICTURE
AUDIO
SETUP
OPTION
ENLARGE
PIP/PbyP
1273115031
SCREENPC2 ANALOG1/1
END···[MENU]
2....

E
18

Menu item details
The menu will differ depending on the input mode.
SCREEN (PC2/PC3)
AUTO
The CLOCK, PHASE, H-POS, and V-POS are automatically 
adjusted.
Pressing  performs adjustment.
Use this automatic adjustment when you use the PC2 input 
terminal or PC3 input terminals to display a PC screen for 
the first time or when you change the setting of the PC. (See 
page 23.)
CLOCK
Adjusts frequency for sampling clock for applicable video.
Adjust when there is flickering in the form of vertical...