Jura Capresso Ena 5 User Manual

							11
ENA 5
People, including children, who
  Zdo not have the physical, sensory or mental 
capabilities to use the machine safely or
  Zare inexperienced or lack knowledge in how 
to use the machine safely
must be supervised by a responsible person when 
using it, or must be instructed in how to use it 
correctly.
Safe handling of the CLARIS filter cartridges:
  ZFilter cartridges should be kept out of the 
reach of children.
  ZStore filter cartridges dry in the sealed 
package.
  ZProtect filter cartridges from heat and direct 
sunlight.
  ZDo NOT use damaged filter cartridges.
  ZDo NOT open filter cartridges.
Welcome to the world of JURA
JURA on the Internet 
Visit us on the Internet.
  @At www.jura.com you will find the latest 
interesting information about your ENA and 
all facets of the world of coffee. 
Knowledge Builder  
You can also get to know your ENA in a fun way 
on the PC.
  @The Knowledge Builder awaits you at 
www.jura.com. LEO, the interactive 
assistant, will assist you and explain the 
benefits of ENA and how it is used.
Connector System©  
The Connector System© permits the use of four 
different nozzles:
  ZProfessional Cappuccino Frother
  UCappuccino
  UHot milk
  ZEasy Cappuccino Frother
  UCappuccino
  Z2-stage frothing nozzle
  UCappuccino
  UHot milken
en
it
en
it 
						

							12
ENA 5
  ZHot water nozzle
3-colour plain text display 
Your ENA features a 3-colour plain text display. 
The colours of the display texts have the following 
meanings:
  ZGreen: Your ENA is ready for use.
  ZRed: The ENA is prompting you to perform an 
action.
  ZYellow: You are in programming mode.
1  Preparing and using for the first time  
This chapter provides the information you need 
for trouble-free use of your ENA and gives you a 
step-by-step guide to preparing your ENA for your 
first coffee experience.
Setting up 
When setting up your ENA, please note the 
following:
  ZPlace the machine on a horizontal surface 
that cannot be damaged by water.
  ZSelect a position for the ENA where it is 
protected against overheating.
Filling the water tank 
To enjoy perfect coffee we recommend changing 
the water every day.
CAUTION
Milk, mineral water or other liquids can damage 
the water tank or the machine.
  TOnly fill the water tank with fresh, cold 
water.
  TRemove the water tank and rinse with cold 
water.
  TFill the water tank with cold, fresh water 
and replace the tank.
Filling the bean container 
CAUTION
Coffee beans which have been treated with 
additives (e.g. sugar), pre-ground or freeze-dried 
coffee will damage the grinder.
  TOnly use untreated coffee beans to refill the 
bean container.
  TRemove the bean container cover.
  TRemove any dirt or foreign objects from 
the bean container.
  TFill the bean container with coffee beans.
  TClose the bean container.
First-time use 
  EThe on/off button also acts as a power 
switch. When the ENA is switched off, the 
machine is completely disconnected from 
the power supply.
  JWARNING
If the machine is operated with a defective power 
cable, there is a danger of electric shock.
  TNever use a machine which has a defective 
power cable.
Precondition: The water tank must be full.
  TInsert the mains plug into a power socket.
 Q  T  Press the on/off button to switch the 
machine on.
SPRACHE DEUTSCH 
						

							13
ENA 5
 g  T  Turn the Rotary Switch until LANGUAGE 
ENGLISH
 is displayed.
 k  T  Press the Rotary Switch to confirm the 
language setting.
OK, the language is then adjusted.
OPEN TAP
  TPlace a receptacle under the nozzle.
 l  T  Turn the switch to position m.
SYSTEM FILLING
CLOSE TAP
 y  T  Turn the switch to position o.
HEATING
PRESS ROTARY
  TPlace a receptacle under the coffee spout.
 k  T  Press the Rotary Switch to start rinsing.
RINSIN G
READY
  EWhen a coffee speciality has been prepared 
for the first time, it is possible that 
FILL  
BEANS
 appears on the display as the 
grinder has not yet been completely filled 
with coffee beans. In this case prepare a 
different coffee speciality.
Using and activating filter 
Your ENA no longer requires descaling if you use 
CLARIS filter cartridges.
  EPerform the ‘Insert filter’ operation without 
interruptions. This will ensure optimum 
function of your ENA.
  EAfter two months the filter capacity is 
reached. The elapsed time can be checked 
with the date plate on the cartridge holder.
Precondition: 
READY appears on the display.
  TOpen the cover behind the Rotary Switch.
 P  T  Press the P button until RINSE appears.
 g  T  Turn the Rotary Switch until FILTER - 
is displayed.
 k  T  Press the Rotary Switch to enter the 
programme item.
NO -
 g  T  Turn the Rotary Switch until YES p 
appears.
 k  T  Press the Rotary Switch to confirm the 
setting.
OK
INSERT FILTER
  TRemove and empty the water tank.
  TOpen the cartridge holder.
  TInsert the new filter cartridge into the water 
tank, pressing it slightly.
  TClose the cartridge holder. It will click into 
place audibly.
  TFill the water tank with cold, fresh water 
and replace the tank.
  TPlace a receptacle (at least 500 ml) under 
the nozzle.
en
en
it
en
it 
						

							14
ENA 5
 k  T  Press the Rotary Switch.
OPEN TAP
 l  T  Turn the switch to position m.
FILTER RINSING, water is dis-
charged from the nozzle.
  ERinsing of the filter can be interrupted at 
any time. To this purpose turn the switch 
clockwise.
  EThe water may be slightly discoloured. This 
is not harmful to health and does not affect 
the taste.
Rinsing of the filter stops automatically, 
CLOSE TAP.
 y  T  Turn the switch to position o.
HEATING
READY
The filter is now activated. 
Determining and adjusting the water 
hardness 
The harder the water, the more frequently the 
ENA requires descaling. It is therefore important 
to adjust the water hardness.
  EIt is not possible to adjust the water 
hardness if the CLARIS filter cartridge is 
used and activated.
  EThe water hardness can be adjusted 
between 1° dH and 30° dH. It can also be 
deactivated, which means that the ENA will 
not indicate when it has to be descaled. 
The Aquadur® test strip supplied as standard can 
be used to determine the water hardness.
  THold the test strip briefly (for one second) 
under running water.
  TShake off the water.
  TWait for approximately 1 minute.
  TRead the degree of water hardness from the 
discolouration of the Aquadur® test strip 
and the description on the packaging.
The water hardness can then be adjusted.
Example: Changing the water hardness from 
16°d H to 25°dH.
Precondition: 
READY appears on the display.
  TOpen the cover behind the Rotary Switch.
 P  T  Press the P button until  RINSE appears.
 g  T  Turn the Rotary Switch until HARDNESS 
is displayed.
 k  T  Press the Rotary Switch to enter the 
programme item.
16°d H
 g  T  Turn the Rotary Switch until 25°dH is 
displayed.
 k  T  Press the Rotary Switch to confirm the 
setting.
OK, the water hardness is then adjusted.
HARDNESS
 g  T  Turn the Rotary Switch until EXIT is 
displayed.
 k  T  Press the Rotary Switch to exit program-
ming mode.
READY
Adjusting grinder  
You can adjust the grinder continuously to suit 
the roast of your coffee.
CAUTION
If you adjust the fineness of grind when the 
grinder is not operating, the grinding wheel could 
be damaged.
  TOnly adjust the fineness of grind when the 
grinder is running.
The fineness of grind setting is correct if the 
coffee flows regularly from the coffee spout. A 
fine, thick crema is also formed.
Our recommendations:
  ZSelect a fine setting for a light roast. 
						

							15
ENA 5
  UIf the fineness of grind setting is too fine, 
the coffee only drips from the coffee spout.
  ZSelect a coarse setting for a darker roast.
  UIf the fineness of grind is too coarse the 
coffee flows too quickly from the coffee 
spout.
Example: Adjusting the fineness of grind during 
coffee preparation.
  TPlace the cup under the coffee spout.
 k  T  Press the Rotary Switch to start coffee 
preparation.
  TTurn the fineness of the grinding wheel to 
the desired position while the grinder is 
running.
1 CUP, the pre-set amount of water flows 
into the cup, preparation stops automati-
cally.
READY
Switching on the machine 
When the ENA is switched on, a prompt to 
perform a rinse operation automatically appears.
 Q  T  Press the on/off button to switch the 
ENA on.
HEATING
PRESS ROTARY
  TPlace a receptacle under the coffee spout.
 k  T  Press the Rotary Switch to start rinsing.
RINSIN G, the system is being rinsed. 
The operation stops automatically.
READY
Switching off the machine 
When the ENA is switched off, the system is 
automatically rinsed if a coffee speciality has been 
prepared.
  TPlace a receptacle under the coffee spout.
  TTurn the coffee spout to the cleaning 
position.
 Q  T  Press the on/off button.
RINSIN G, the system is being rinsed, 
the operation stops automatically. The ENA 
is switched off.
  TTurn the coffee spout to the 1 cup or 2 cup 
position.
  EThe On/Off button also acts as a power 
switch. When the ENA is switched off, the 
machine is completely disconnected from 
the power supply.
en
en
it
en
it 
						

							16
ENA 5
2 Preparation
1 coffee at the touch of a button   
Precondition: READY appears on the display.
  TTurn the coffee spout to the 1 cup position.
  TPlace the cup under the coffee spout.
 k  T  Press the Rotary Switch to start coffee 
preparation.
During grinding the strength of the coffee 
is briefly displayed.
1 CUP, the pre-set amount of water flows 
into the cup, preparation stops automati-
cally.
READY
2 coffees at the touch of a button
Precondition: READY appears on the display.
  TTurn the coffee spout to the 2 cup position.
  T Place two cups under the coffee spout.
 g  T  Turn the Rotary Switch until 2 CUPS 
is displayed.
 k  T  Press the Rotary Switch to start coffee 
preparation.
2 CUPS, the pre-set amount of water 
flows into the cups, preparation stops 
automatically.
READY
Pre-ground coffee  
You can also use a second coffee blend in the 
powder chute for pre-ground coffee.
  ENever add more than two level measuring 
spoons of pre-ground coffee.
  EDo not use very finely-ground coffee. Very 
fine coffee can block up the system so 
that the coffee only comes out in drips.
  EIf the filled amount of pre-ground coffee 
was insufficient, 
NOT ENOUGH 
PRE-GROUND
 is displayed and the 
ENA stops operation.
  EThe desired coffee speciality must be 
prepared within approx. one minute 
after filling with the pre-ground coffee. 
Otherwise the ENA stops the operation 
and is ready to use again.
Example: Preparing a cup of coffee using 
pre-ground coffee.
Precondition: 
READY appears on the display 
and the coffee spout is set at the 1 cup position.
  TPlace the cup under the coffee spout.
  TOpen the powder chute.
FILL PRE-GROUND
  TPlace the filler funnel for pre-ground coffee 
in the powder chute.
  TPlace one level measuring spoon of 
pre-ground coffee into the filler funnel.
  TRemove the filler funnel.
  TClose the powder chute.
1 CUP
 k  T  Press the Rotary Switch to start coffee 
preparation. 
						

							17
ENA 5
1 CUP, the pre-set amount of water flows 
into the cup, preparation stops automati-
cally.
READY
  EIt is also possible to prepare two cups of 
pre-ground coffee. To this purpose place 
two level measuring spoons of pre-ground 
coffee into the filler funnel. Turn the Rotary 
Switch to 
2 CUPS and press to start 
coffee preparation.
One-off setting before and during 
preparation 
The coffee strength can be changed before 
preparation or during the grinding operation.
The following coffee strength options are possible 
for 1 coffee:
  ZMild
  ZNormal
  ZStrong
  E2 coffees are always prepared with the 
coffee strength ‘mild’.
  EThe pre-set amount of water can be 
changed during the brewing operation by 
turning the Rotary Switch.
One-off settings before and during coffee 
preparation always follow this model. These 
settings are not saved.
Example: Changing the coffee strength of 
1 coffee before preparation from 
NORMAL 
to 
STRONG.
Precondition: 
READY appears on the display 
and the coffee spout is set at the 1 cup position.
  TPlace the cup under the coffee spout.
 g  T  Turn the Rotary Switch until STRONG is 
displayed.
 k  T  Press the Rotary Switch until STRONG is 
displayed.During grinding the coffee strength 
STRONG is displayed.
1 CUP, the pre-set amount of water flows 
into the cup, preparation stops automati-
cally.
READY
Entering a default setting for the amount of 
water for a cup size 
  EA default setting can be entered for the 
amount of water for 1 coffee. When 
preparing 2 coffees this amount is 
dispensed per cup.
Precondition: 
READY appears on the display 
and the coffee spout is set at the 1 cup position.
  TPlace the cup under the coffee spout.
 k  T  Press the Rotary Switch and hold it down.
During grinding the strength of the coffee 
is displayed.
 k  T  Continue to hold the Rotary Switch down 
until 
ENOUGH COFFEE ? appears.
The coffee flows into the cup.
 k  T  Press the Rotary Switch again when enough 
coffee has been filled into the cup.
OK, the default setting for the amount of 
water for one coffee has been entered.
READY
  EThis setting can be changed at any time by 
repeating the above procedure.
Cappuccino with the Professional 
Cappuccino Frother 
Precondition: READY appears on the display 
and the coffee spout is set to the 1 cup position.
  TRemove the protective cover from the 
Professional Cappuccino Frother.
  TConnect the milk pipe to the nozzle.
  TInsert the other end of the milk pipe into a 
milk carton or connect it to a milk 
container.
en
en
it
en
it 
						

							18
ENA 5
  TPlace a cup under the nozzle.
  TSet the selector lever of the nozzle to the 
milk foam 
p position.
 g  T  Turn the Rotary Switch until STEAM is 
displayed.
 k  T  Press the Rotary Switch.
HEATING
READY
 appears as soon as the ENA is 
sufficiently heated.
 l  T  Turn the switch to position m.
STEAM, the milk foam is being prepared.
 y  T  Turn the switch clockwise to position o 
when there is sufficient milk foam in the 
cup.
  EYou can prepare more milk foam within 
about 40 seconds.
  TPlace the cup under the coffee spout.
 k  T  Press the Rotary Switch to start coffee 
preparation.
1 CUP, the pre-set amount of water flows 
into the cup. Preparation stops automati-
cally.
To ensure that the Professional Cappuccino 
Frother works perfectly, it should be rinsed 
and cleaned regularly (refer to Chapter 4 
‘Maintenance – Professional Cappuccino 
Frother’).
Cappuccino with the Easy Cappuccino 
Frother 
Precondition: READY appears on the display 
and the coffee spout is set at the 1 cup position.
  TRemove the protective cover from the 
Easy Cappuccino Frother.
  TConnect the milk pipe to the nozzle.
  TInsert the other end of the milk pipe into a 
milk carton or connect it to a milk 
container.
  TPlace a cup under the nozzle.
 g  T  Turn the Rotary Switch until STEAM is 
displayed.
 k  T  Press the Rotary Switch.
HEATING
READY
 appears as soon as the ENA is 
sufficiently heated.
 l  T  Turn the switch to position m.
STEAM, the milk foam is being prepared.
 y  T  Turn the switch clockwise to position o 
when there is sufficient milk foam in the 
cup.
  EYou can prepare more milk foam within 
about 40 seconds.
  TPlace the cup under the coffee spout.
 k  T  Press the Rotary Switch to start the coffee 
preparation.
1 CUP, the pre-set amount of water flows 
into the cup. Preparation stops automati-
cally.
To ensure that the Easy Cappuccino Frother 
works perfectly, it should be rinsed and 
cleaned regularly (refer to Chapter 4 
‘Maintenance – Easy Cappuccino Frother’). 
						

							19
ENA 5
Cappuccino with the 2-stage frothing nozzle 
Precondition: READY appears on the display 
and the coffee spout is set at the 1 cup position.
  TPush the 2-stage frothing nozzle to the 
lower position.
  TPlace a cup of milk below the 2-stage 
frothing nozzle and immerse the nozzle in 
the milk.
  EIf the nozzle does not reach into the cup, lift 
the cup towards the nozzle.
 g  T  Turn the Rotary Switch until STEAM is 
displayed.
 k  T  Press the Rotary Switch.
HEATING
READY
 appears as soon as the ENA is 
sufficiently heated.
 l  T  Turn the switch to position m.
STEAM, the milk is foamed by the hot 
steam.
 y  T  Turn the switch to position o when the 
milk foam has reached the required 
consistency.
  EYou can prepare more steam within about 
40 seconds.
  TPlace the cup under the coffee spout.
 k  T  Press the Rotary Switch to start coffee 
preparation.
1 CUP, the pre-set amount of water flows 
into the cup. Preparation stops automati-
cally.
To ensure that the 2-stage frothing nozzle 
works perfectly, it should be rinsed 
regularly (refer to Chapter 4 ‘Maintenance – 
Dismantling and rinsing the 2-stage 
frothing nozzle’).
Heating milk with the Professional 
Cappuccino Frother 
Precondition: READY appears on the display.
  TRemove the protective cover from the 
Professional Cappuccino Frother.
  TConnect the milk pipe to the nozzle.
  TInsert the other end of the milk pipe into a 
milk carton or connect it to a milk 
container.
  TPlace a cup under the nozzle.
  TSet the selector lever of the nozzle to the 
milk 
t position.
 g  T  Turn the Rotary Switch until STEAM is 
displayed.
 k  T  Press the Rotary Switch.
HEATING
READY
 appears as soon as the ENA is 
sufficiently heated.
 l  T  Turn the switch to position m.
STEAM, the hot milk is being prepared.
 y  T  Turn the switch clockwise to position o 
when there is sufficient milk in the cup.
  EYou can prepare more hot milk within 
about 40 seconds.
To ensure that the Professional Cappuccino 
Frother works perfectly, it should be rinsed 
and cleaned regularly (refer to Chapter 4 
‘Maintenance – Professional Cappuccino 
Frother’).
en
en
it
en
it 
						

							20
ENA 5
Heating milk with the 2-stage frothing 
nozzle 
Precondition: READY appears on the display.
  TPush the 2-stage frothing nozzle to the top 
position.
  TPlace a cup of milk below the 2-stage 
frothing nozzle and immerse the nozzle in 
the milk.
  EIf the nozzle does not reach into the cup, lift 
the cup towards the nozzle.
 g  T  Turn the Rotary Switch until STEAM is 
displayed.
 k  T  Press the Rotary Switch.
HEATING
READY
 appears as soon as the ENA is 
sufficiently heated.
 l  T  Turn the switch to position m.
STEAM, the milk is heated by the hot 
steam.
 y  T  Turn the switch to position o as soon as 
the required temperature is reached.
  EYou can prepare more steam within about 
40 seconds.
To ensure that the 2-stage frothing 
nozzle works perfectly, it should be 
rinsed regularly (refer to Chapter 4 
‘Maintenance – Dismantling and rinsing 
the 2-stage frothing nozzle’).
Hot water   
  ETo prepare hot water, attach either the hot 
water nozzle or the 2-stage frothing nozzle 
to the Connector System
©.
  JCAUTION
There is a danger of scalding from hot water 
splashes.
  TAvoid direct contact with the skin.
Precondition: 
READY appears on the display.
  TPlace a cup under the nozzle.
 l  T  Turn the switch to position m.
WATER, hot water flows into the cup.
 y  T  Turn the switch clockwise when there is 
sufficient water in the cup.
READY
3  Default settings in programming 
mode 
Products
The following settings can be programmed for 
1 coffee:
  ZAmount of water: 25 ML – 240  ML
  ZCoffee strength: MILD, NORMAL, 
STRONG
  ZTemperature: NORMAL, HIGH
The following applies when preparing 2 coffees:
  ZThe amount of water set for 1 coffee is 
dispensed per cup when 2 cups are prepared.
  Z2 coffees are always prepared with the coffee 
strength ‘mild’.
  Z2 coffees are prepared at the same tempera-
ture which is set for 1 coffee.
Default settings in programming mode always 
 follow the same model.
Example: Changing the default setting for the 
strength of one coffee from 
NORMAL to 
STRONG.