Juiceman ALLINONE JUICE EXTRACTOR CITRUS JUICER JM480S User Manual

							
1
Enjoy the Fresh Side of LifeTM
MODEL/MODELO
❍ JM480S
CustomerCr Line:
USA/Canada
1-800-231-9786
Mexico 
01-800 714-2503
Accessories/Parts 
(USA / Canada) 
Accesorios/Partes 
(EE.UU / Canadá) 
1-800-738-0245
Enjoy the Fresh Side of LifeTM
CustomerCrLine:
All-in-One Juice Extractor 
& Citrus Juicer
Extractor de jugo 
y exprimidor de cítricos 
todo en uno
For online customer service and to register your product, go to 
www.prodprotect.com/applica 
						

							


Please Read and Save this Use and Care Book 
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always 
be followed including the following:
❍ Read all instructions.
❍ To protect against risk of electrical shock do not put cord, plugs or 
appliance in water or other liquid.
❍ Close supervision is necessary when any appliance is used by or near 
children.
❍ Unplug from outlet when not in use, before putting on or taking off 
parts, and before cleaning.
❍ Avoid contacting moving parts. 
❍ Do not operate any appliance with a damaged cord or plug or after 
the appliance malfunctions, or is dropped or damaged in any manner. 
Return appliance to the nearest authorized service facility for 
examination, repair or electrical or mechanical adjustment. Or, call 
the appropriate toll-free number on the cover of this manual.
❍ The use of attachments not recommended or sold by the 
manufacturer may cause fire, electric shock or injury.
❍ Do not use outdoors.
❍ Do not let cord hang over edge of table or counter.
❍ Always make sure juicer cover is clamped securely in place before 
motor is turned on. Do not unfasten clamps while juicer is in 
operation.
❍ Be sure to turn switch to OFF (0) position after each use of your juicer. 
Make sure the motor stops completely before disassembling.
❍ Do not put your fingers or other objects into the juicer opening while 
it is in operation. If food becomes lodged in opening, use food pusher 
or another piece of fruit or vegetable to push it down. When this 
method is not possible, turn the motor off and disassemble juicer to 
remove remaining food.
❍ Do not use the appliance if the rotating sieve is damaged.
❍ Do not operate without the pulp container in place.
SAVE THESE INSTRUCTIONS
This product is for household use only. 
						

							


POLARIZED PLUG (10V Models Only)
This appliance has a polarized plug (one blade is wider than the other). To reduce 
the risk of electric shock, this plug is intended to fit into a polarized outlet only 
one way. If the plug does not fit fully into the outlet, reverse the plug. If it still 
does not fit, contact a qualified electrician. Do not attempt to modify the plug in 
any way.
TAMPER-RESISTANT SCREW
Warning: This appliance is equipped with a tamper-resistant screw to prevent 
removal of the outer cover. To reduce the risk of fire or electric shock, do not 
attempt to remove the outer cover. There are no user-serviceable parts inside. 
Repair should be done only by authorized service personnel.
ELECTRICAL CORD
a) A short power-supply cord (or detachable power-supply cord) is to be provided 
to reduce the risk resulting from becoming entangled in or tripping over a 
longer cord.
b)  Longer detachable power-supply cords or extension cords are available and 
may be used if care is exercised in their use.
c)  If a long detachable power-supply cord or extension cord is used,
1)  The marked electrical rating of the detachable power-supply cord or 
extension cord should be at least as great as the electrical rating of the 
appliance,
2)  If the appliance is of the grounded type, the extension cord should be a 
grounding-type 3-wire cord, and
3)  The longer cord should be arranged so that it will not drape over the 
countertop or tabletop where it can be pulled on by children or tripped over.
Note: If the power supply cord is damaged, it should be replaced by qualified 
personnel or in Latin America by an authorized service center.
Note: The maximum wattage is obtained with the centrifugal juicer attachment.  
Other recommended attachments draw significantly less power. 
						

							


GETTING TO KNOW YOUR JUICE EXTRACTOR & CITRUS JUICER
† 1. Small food pusher  
      (Part # JM480S-01)
†  2. Large food pusher 
 
      (Part # JM480S-02)
    3. Feed chute 
†  4. Lid
 (Part # JM480S-03)
†  5. Stainless steel filter 
      (Part # JM480S-04)
†  6. Integrated pulp container 
      (Part # JM480S-05)
    7. Locking latches (both sides)
    8. Speed control switch
    9. Base
    10. Cord wrap (under base)
    11. Slip-resistant feet    
12. Snap up juice spout
†  13. Juice pitcher
 (Part # JM480S-06)
†  14. Citrus juicer drive shaft
      (Part # JM480S-07)
†  15. Citrus juicer attachment 
      (Part # JM480S-08)
†  16. Small juicing cone 
 
      (Part # JM480S-09)
†  17. Large juicing cone 
 
            (Part # JM480S-10)
†  18. Cleaning brush 
 
      (Part # JM480S-11)
Note: † indicates consumer replaceable/removable parts














 
						

							


How to Use
This product is for household use only.
GETTING STARTED
•   Remove all packing material and, if applicable, any stickers from the product. 
Remove and save literature.
•    Please go to www.prodprotect.com/applica to register your warranty. For 
additional information and recipes for your product go to www.juiceman.com. 
•    Take the appliance apart following instructions in DISASSEMBLING THE 
CITRUS JUICER and wash all removable parts as instructed in CARE 
AND CLEANING.  This will remove any traces of dust or residue left from 
manufacturing and shipping. 
Important: Do not rinse or immerse base in water or any other liquid.
•   Place base on a dry, level counter to prepare and assemble, following 
instructions in ASSEMBLING THE JUICE EXTRACTOR.
•    Once assembled place the appliance on a level dry space, allowing air space 
 
on all sides to provide proper ventilation for the motor.
PREPARATION 
How to prepare fruits and vegetables for juicing.
Purchasing and Storing Ingredients:
•   Always use fresh fully ripened fruits and vegetables. 
•    When purchasing consider selecting fruits and vegetables in season for best 
freshness and flavor.  
•    Choose fruits that are plump, tender and have bright color. Fruits should be 
heavy for their size without bruises, cuts or blemishes. 
•    To ripen fruit, place in a small clean paper bag. Close the bag loosely and
 
let stand at room temperature. (To speed ripening, add a ripe apple or  
banana to the bag.) Once ripened, store in the refrigerator for a day or 2 until 
ready to use. 
•  Store perishable vegetables in the refrigerator until ready to use. 
Preparing Fruits and Vegetables for the Juice Extractor:
•   Wash fruits and vegetables thoroughly just before using in the juice extractor 
using a natural bristle brush and a biodegradable cleaner to help remove 
pesticide residue.  
						

							


•   If desired, remove the skin. The skin may be left on all produce with the 
exception of: 
  o All citrus fruits, including 
    • Oranges 
    • Grapefruit 
    • Lemons 
    • Limes 
    • Tangerines 
Note: The oil in the skin of these fruits tastes bitter and is difficult to digest.
Hint: Although the skin may be left on melons and pineapple, you may choose to 
remove them to maximize the fruit flavor in the finished drink.
•  All pits and large seeds should be removed from fruits, including: 
  o Apricots 
  o Cherries 
  o Nectarines 
  o Mangoes 
  o Peaches 
  o Plums 
  o Melons 
•    Remove and discard outer leaves of non-organic produce.  Peel away any 
 
wax coatings. 
•  Trim any bruised or discolored sections of fruits and vegetables.
•    The design of the feed chute accommodates larger produce. It will easily 
accommodate most whole fruits and vegetables, such as, apples, beets, 
carrots and celery. If necessary, cut into large pieces before inserting into  
feed chute. 
•    Be sure all parts of the juice extractor and clean and dry. See the CARE AND 
CLEANING instructions section of the manual on page 12.
DISASSEMBLING THE JUICE EXTRACTOR
1.    Pull open at the bottom of each locking latch 
to disengage from the tab on the cover (B). The 
locking latches will raise up, so you can release 
them from the lid.
2.    To remove the lid, take out the food pusher, 
grasp the feed chute and pull up.
B 
						

							


3.  To remove the integrated pulp container, grip the 
snap up juice spout with one hand and the back 
edge of the pulp container with the other. Pull up 
with the stainless steel filter in place (C).
4.   To remove the stainless steel filter, hold the juice 
spout and grasp the stainless steel filter by the rim 
to pull it out (D).
Caution: The stainless steel filter cutting teeth are 
very sharp. Handle it carefully.
 
ASSEMBLING THE JUICE EXTRACTOR
1.  Place integrated pulp container on the base with 
the juice spout facing you.
2.   Insert the stainless steel filter in the center of the 
integrated pulp container and press down until it 
snaps into place (E). 
3.  Place the lid on top of the integrated pulp      
   container.
4.   Insert the desired food pusher into the feed 
chute (see USING THE SMALL AND LARGE FOOD 
PUSHERS). Place the food pusher into the feed 
chute, matching the indentations on the food 
pusher to the projections on the feed chute.
5.   Lock the locking latches by holding down the cover 
as you fit the locking mechanism at the top of each 
latch over the tab on each side of the lid (F). Press 
the bottom of each latch until you hear it click into 
place.
Important:  The appliance will not operate until the 
locking latches are locked.
6.  Tilt the juice spout down into the open 
()  
position (G).
7.  Place the juice pitcher under the juice spout. 
C
D 
E 
F 
G  
						

							


USING YOUR JUICE EXTRACTOR
Note: To begin, assemble the fruits and or vegetables to be used on the counter 
or in a bowl next to the extractor, following the tips in PREPARATION.
Important: The integrated pulp container holds about ½ cups of pulp. 
 
Do not allow the integrated pulp container to overfill. This may cause the 
appliance to stall.
1.   Plug appliance into a standard electrical outlet. Press the speed control switch 
to the low setting (1) and allow it to run 10 seconds before placing any food into 
the feed chute.
2.  Place food in the feed chute and press lightly with food pusher. 
3.    Use the food pusher as a guide to gently direct the produce through the feed 
chute. To get the most juice from the fruits and vegetables, do not force or 
rush the food through the appliance.
4.    When the pulp container or juice pitcher is almost full (the pulp container 
holds about 3½ cups of pulp and the juice pitcher holds about 4 cups of juice) 
turn off (0). Allow the motor to come to a complete stop before emptying either 
part. 
5.    Follow the instructions in DISASSEMBLING YOUR JUICE EXTRACTOR to 
remove the pulp container, then replace following instructions in ASSEMBLING 
YOUR JUICE EXTRACTOR.  Be sure to replace the containers before resuming 
extraction.
Caution: The stainless steel filter cutting teeth are very sharp. Handle the  
filter carefully.
6.   When juicing is complete, lift the snap up juice spout into the closed 
 
position ().
7.  Turn off and unplug from outlet.
Note: Never place fingers or hand into the feed chute.
USING THE SMALL AND LARGE FOOD PUSHERS
Note: The food pusher has 2 parts; the smaller clear inner section locks into 
 the larger outer section.
1.   To remove the small food pusher, hold the 
large food pusher with one hand and twist 
counterclockwise until the lock of the inner 
section is disengaged;  
lift the small food pusher straight up (H). 
2.    Place the large food pusher into the feed chute, 
matching the indentations on the food pusher to 
the projections on the feed chute.
Note: Use the smaller opening for small fruits and 
vegetables. Use the small food pusher to help guide 
the fruits and vegetables through the opening in the          
  large food pusher.H  
						

							


3.  When using larger pieces of fruits and vegetables, 
replace the small food pusher into the large food 
pusher and use the assembled piece to help guide 
the larger fruits and vegetables through the feed 
chute. Match the notches to the opening. The clear 
center will drop into the slot; turn the top clockwise 
until the small pusher is locked in place (J). 
JUICE EXTRACTOR TIPS
•  Do not put food into the extractor before turning the appliance on. 
•    Let the appliance run for at least 10 seconds before placing any food into the 
feed chute. 
•    Do not let the juice or pulp container overfill while using the machine. Turn 
the appliance off (0), wait for the motor to stop running and any juice to stop 
flowing.  Empty the juice and/or pulp container. Be sure they are properly 
replaced before resuming operation of the extractor. 
•    Do not process bananas, avocados or coconut. They have no juice and will clog 
the appliance. 
•  Be sure to remove all pits and large seeds from fruits. 
•  For maximum nutritional benefits, drink your processed juice right a way. 
FOR OPTIMUM JUICING
• Avoid excessive build up of pulp on the underside of the lid. 
•  Remove rind of melons; because they are so thick, they water down drinks.
•  Refrigerate washed ripe fruits and vegetables until ready to use. 
USES FOR THE PULP
The pulp from the fruits and vegetables is high in nutritional value. Use it to add 
fiber and flavor to muffins and quick breads. Use it to thicken soups, casseroles 
and sauces. Use fruit pulp to add nutrition and flavor to desserts, such as, 
puddings and cakes. Be sure to use it the same day you extract the juice.
Pulp is also food for your garden. You can use it as compost.
J  
						

							
10

DISASSEMBLING THE CITRUS JUICER
1. Lift the juice spout into the closed  
() position.
2.  Remove the juice pitcher from under the spout.
3.  To unlock the locking latches, pull open at the bottom of each latch to      
  disengage from the tabs on the cover. The latches will raise and be released    
  from the cover 
(see M).
4.  Lift the juicing cone assembly from the citrus juicer attachment.
5.  Lift the citrus juicer attachment from the integrated pulp container.
6.  Lift the pulp container and the drive shaft from the base.
ASSEMBLING THE CITRUS JUICER
1.  Place the integrated pulp container on the motor 
base.
2.   Place the citrus juicer drive shaft into the center 
of the integrated pulp container and press down to 
make sure it is seated securely on the base (K). 
3.   Place the citrus juicer attachment on top of the 
integrated pulp container so that the two small lock 
tabs are to the right and left (L).
4.   Lock the locking latches by holding down the cover 
as you as you fit the locking mechanism at the 
top of each latch over the tab on each side of the 
attachment (M). Press the bottom of each latch 
until you hear it click into place.
Important: The appliance will not operate until the 
locking latches are locked.
5. Place the juice pitcher under the juice spout. 
6.   Tilt the juice spout into the open 
() position  
(see G on page )
. 
7.   Choose your desired citrus cone and place on the 
drive shaft (see USING THE JUICING CONES). 
USING THE JUICING CONES
Note: The small cone is recommended for small 
fruits, such as lemons and limes and the large cone 
for larger fruits, such as oranges and grapefruit.
1.  Hold the small juicing cone in one hand by      
the 2 prongs. Place the thumb and forefinger of  
the other hand on the large juicing cone    
directly above the prongs. Press lightly and lift the    
conecompletely off. The small juicing cone will be    
revealed.
K 
L 
M