JBL Sdp5 Manual

Troubleshooting & MaintenanceJBL Synthesis
6-23. Make sure audio has not been muted. The message “MUTE
ON” or “FULL MUTE ON” will appear on the on-screen and
front panel displays when audio has been muted. To deactivate
mute, press the front panel or remote control Mute button or
use the front panel volume knob or the remote control VOL 

and buttons to adjust volume level.
4. Check the INPUT SETUP menu DIGITAL IN and ANALOG IN
parameters to ensure the appropriate audio connector is
assigned to the...

Troubleshooting & MaintenanceSDP-5
6-3
The SDP-5 is powered on, but there is no video.
1. Examine the video cables – particularly the S-video cables – to
ensure a good connection to the associated component. 
2. Check the INPUT SETUP menu VIDEO IN (page 3-11) and
COMPONENT IN (page 3-12) parameters to ensure the
appropriate video connector is assigned to the selected input.
RF interference is present in the audio or video.
1. Make sure the SDP-5 is not positioned near unshielded TV or
FM antennas, cable...

Troubleshooting & MaintenanceJBL Synthesis
6-4The Mute button must be pressed within 2 seconds of
activating the SDP-5. If the message MUTE ON appears on
the on-screen and front panel displays when the Mute button
RESTORING FACTORY-DEFAULT SETTINGS
When factory-default settings are restored, all parameters and
user-defined values are restored to their factory-default settings.
Before restoring factory-default settings, it is recommended to
record all user-defined settings on the installation worksheet...

A
Appendix
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
Menu Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-4
Installation Worksheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-14 

Main Zone Audio Performance(continued)
Zone 2 Audio Performance
Main Zone Audio Performance
Audio Input & Output Connectors
AppendixJBL Synthesis
A-2
SPECIFICATIONS
•8 stereo (RCA) or5 stereo and one 5.1-channel or2
stereo and two 5.1-channel connectors
•4 S/PDIF coaxial (RCA) and 4 S/PDIF optical (TosLink)
connectors
•Coaxial and optical input connectors conform to IEC-
958, S/PDIF standards
•Accepts 44.1, 48, 88.2, and 96kHz sample rates
•Accepts 16-24 bits PCM audio, Dolby Digital, dts, and
dts-ES...

Component Video Performance
Component Video Performance(continued)
Other
•150MHz Insertion Loss
Bandwidth
•1 power on/off and 1 programmable connector on
detachable screw terminals (+12 VDC, 0.5 amps each) Trigger Outputs
•2 9-pin D-sub connectors
•90-250 VAC, 50-60Hz, 60W (universal line input),
detachable power cord
•Hand-held, backlit infrared remote control unit
•Requires 2 AA batteries (Alkaline batteries recommended) •Height (with feet): 5.04 inches (128mm)
•Width: 17.3 inches (440mm)
•Depth: 14.85...

AppendixJBL Synthesis
A-4
DECLARATION OF CONFORMITY
Application of Council Directive(s):
89/336/EEC and 93/68/EEC
Standard(s) to which Conformity is Declared:
EN55022:1994 + A1:1995 + A2:1997, EN55024:1998,
EN61000-3-2: 2000, EN61000-3-3:2000, and
EN60065: 1998
Manufacturer:Lexicon, Inc.
3 Oak Park
Bedford, MA  01730-1413  USA
The equipment identified here conforms to the Directive(s)
and Standard(s) specified above.
Type of Equipment:Digital Controller
Model:JBL Synthesis SDP-5
Date:February 2003...

TOP
CENTER
BOTTOM
DISPLAY SETUP
ON-SCREEN DISPLAY
FRONT PANEL DISPLAY
A/V SYNC DELAY OFF
CUSTOM NAME OFF
EDIT CUSTOM NAMESPEAKER SETUP
CUSTOM SETUP
SYNTHESIS 7CH SETUP
SPEAKER DISTANCES
LEVELS CALIBRATION
80Hz80Hz
80Hz80Hz80Hz
80Hz80Hz
80Hz
L M
SUB
R
C
SL
SR
RL
RR
continued on page A-8
AppendixSDP-5
A-5
MAIN MENU
MODE ADJUST
AUDIO CONTROLS
SETUP
SETUP

SETUP
INPUTS
SPEAKERS
REAR PANEL CONFIG
DISPLAYS
VOLUME CONTROLS
TRIGGER
LOCK OPTIONS
INPUT SETUP
DVD1
DVD2
SAT
VCR
TV
CD
TUNER
AUX
continued on page A-6...

AppendixJBL
A-6
Menu Tree(continued from page A-5)
Selecting the SETUP menu INPUTS option prompts the selection of the desired input (e.g.
DVD1). Selecting an input opens the corresponding INPUT SETUP menu shown below. The
parameters on the left side of the INPUT SETUP menus are identical regardless of which input
is selected. The parameter settings on the right side are adjustable. Default parameter
settings differ from input to input. The INPUT SETUP menus shown below indicate default
parameter...

AppendixSDP-5
A-7
Selecting an INPUT SETUP menu item opens the
corresponding menu shown below. These menus are
identical regardless of which input is selected. The DVD1
INPUT SETUP menu is shown at the left as an example.
Whenever it appears, any other INPUT SETUP menu shown
on the previous page may be substituted.
DVD1 2-CH MODE
L7FILM
L7TV
L7MUSIC
L7MUSIC SURR
%!PLII + THX
%!PLII MOVIE
%!PLII MUSIC
%!PRO LOGIC
NIGHTCLUB
CONCERT HALL
CHURCH
CATHEDRAL
PANORAMA
PARTY
2-CHANNEL
MONO LOGIC
MONO SURROUND...