InFocus ScreenPla 5700 Projector User Manual

11
Shutting down the projectorPow e r  S av e
The projector has a Power Save feature in the System menu that automati-
cally turns the lamp off after no signals are detected for 20 minutes. After 10 
additional minutes with no signal, the projector powers down. If an active 
signal is received before the projector powers down, the image is displayed. 
Yo u  m u s t  p r e s s  t h e  Pow e r button to display an image after 30 minutes have 
passed. 
Turning off the projector
To turn off the projector,...

12
Problem Solution Result
No startup screenPlug power cable in and remove lens cap
press Power button
Correct image
Image not centered on screenMove projector, adjust zoom, adjust heightCorrect image
ScreenPlay
Adjust horizontal or vertical position in 
Picture>Advanced menuzoom 

13
Image not squareAdjust keystone on keypadSquare image
Image does not fit 16:9 screenChange aspect ratio to 16:9 in 
Picture>Aspect ratio menuCorrect image
Edges of image distortedTurn Overscan on in the Picture menu
Correct image
AB
AB 

14
1. Projected colors don’t match source
2. Colors are washed out or too deep
3. Image from component source appears greenish1. Adjust color, tint, color temperature, 
brightness, or contrast in the menus.
2. Pick another gamma setting
3. Pick another color space
Correct image
Image upside downTurn off Ceiling in Settings>System menuCorrect image
Image reversed left to right
Turn off Rear in Settings>System menu
Correct image 
COLOR
COLOR
A
B
AB
A
AB 

15
Video image “torn” and fragmentedChange Video Standard in 
Picture>Advanced menuCorrect image
Lamp won’t turn on, LED blinking red (page 11)Make sure vents aren’t blocked; allow 
projector to cool for one minute Unplug projector; wait one minute; plug in 
projector and turn it on: lamp lights
A
AB
B
AB
blinksred
 
ScreenPlay 

16
Computer-specific troubleshooting
Only startup screen appearsPress the Source button 
Activate laptop’s external portComputer image projected
No computer image, just the words “Signal out of 
range” Adjust computer refresh rate in Control 
Panel>Display>Settings>Advanced>
Adapter (location varies by operating 
system)Computer image projected
A
ScreenPlay
or restart
laptop
A
A
A
Signal out of
range
A
A 

17 Still having problems?
If you need assistance, call InFocus Customer Service directly at
1-800-799-9911. Support is free between 6 a.m. and 6 p.m. PST, Monday 
through Friday. Support is available in North America after hours and 
weekends for a fee at 1-888-592-6800.
Or, send us an e-mail at
 [email protected].
In Europe, call InFocus in The Netherlands at (31) 20 579 2820. 
In Asia, call InFocus in Singapore at (65) 6334-9005. This product is backed by a limited two-year warranty. When sending...

18
Using the keypad buttonsMost buttons are described in detail in other sections, but here is an over-
view of their functions:
Pow e r–turns the projector on (page 8) and off (page 8).
Menu–opens the on-screen menus (page 21).
Select–confirms choices made in the menus (page 21).
Up/down arrows–navigates to and adjusts settings in the menus (page 21).
Auto image–resynchs the projector to the source.
Presets–cycles through the 3 available user preset settings (page 24).
Key s t o n e–adjusts squareness...

19
Using the remote controlThe remote uses two (2) provided AAA batteries. They are easily installed 
by sliding the cover off the remote’s back, aligning the + and - ends of the 
batteries, sliding them into place, and then replacing the cover.
To operate, point the remote at the projection screen or at the projector (not 
at the video device or computer). The range of optimum operation is 0 to 
30 feet (9.14m).
Press the remote’s Menu button to open the projector ’s menu system. Use 
the arrow buttons...

20
Optimizing video imagesAfter the video device is connected properly and the image is on the screen, 
you can optimize the image using the onscreen menus. For general informa-
tion on using the menus, see page 21.
 Change the Aspect ratio. Aspect ratio is the ratio of the image width to 
image height. TV screens are usually 1.33:1, also known as 4:3. HDTV 
and most DVDs are 1.78:1, or 16:9. Choose the option that best fits your 
input source in the menus, or press the Resize button on the remote to...