InFocus ScreenPla 5700 Projector User Manual

1
ENGLISH
Declaration of ConformityManufacturer: InFocus Corporation, 27700B SW Parkway Ave. Wilsonville, Oregon 
97070 USA
European Office: Strawinskylaan 585, 1077 XX Amsterdam, The Netherlands
We declare under our sole responsibility that the ScreenPlay 5700 projector conforms 
to the following directives and norms:
EMC Directive 89/336/EEC, Amended by 93/68/EEC
EMC: EN 55022
           EN 55024
 EN 61000-3-2
 EN 61000-3-3
Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC
Safety: EN 60950: 2000...

2 Table of Contents
Introduction 3
Positioning the projector  5
Video connections  6
Connecting a video device  7
Displaying a video image  8
Connecting a computer  10
Shutting down the projector  11
Troubleshooting your setup  11
Using the keypad buttons  18
Using the remote control  19
Optimizing video images  20
Customizing the projector  20
Using the menus  21
Picture menu  22
Settings menu  27
Maintenance 29
Cleaning the lens  29
Replacing the projection lamp  30
Appendix 32
Specifications 32...

3
IntroductionCongratulations and thank you for your excellent choice of a superior digi-
tal image projection device. Your new ScreenPlay™ 5700 projector from 
InFocus
® is specifically designed for home cinema applications. The 
ScreenPlay 5700 sets the standard for Enhanced-Definition digital perfec-
tion, featuring true Enhanced Definition 1024x576 resolution using the latest 
DLP™ technology and new DCDi video processing from Faroudja™. Cali-
brated to D65 color mastering standards, the ScreenPlay...

4 Connector Panel
The projector provides eight discreet video connectors: 
two component RCA
two S-video
one composite RCA
 one M1-DA (HD, DVI, and computer)
 one VESA (HD, HD component, and computer)
one component D5
It also has a mini-jack input for a Niles or Xantech-compatible IR repeater 
and an RS-232 connector for serial control. The Command Line Interface 
(CLI) specifications and commands are listed in the Appendix starting on 
page 36.
Two 3.5 mm mini-jack triggers provide 12 volt...

5
Positioning the projectorThere are a number a factors to consider when determining where to set up 
the projector, including the size and shape of your screen, the location of 
your power outlets, and the distance between the projector and the rest of 
your equipment. Here are some general guidelines.1
Position the projector on a flat surface at a right angle to the screen.
The projector must be within 10 feet (3 m) of your power source. To 
ensure adequate cable access, place the projector at least 6...

6
Video connectionsYou can connect VCRs, DVD players, camcorders, digital cameras, video 
games, HDTV receivers, and TV tuners to the projector. (You cannot directly 
connect the coaxial cable that enters your house from a cable or satellite 
company; the signal must pass through a tuner first. Examples of tuners are 
digital cable boxes, VCRs, digital video recorders, and satellite TV boxes. 
Basically, any device that can change channels is considered a tuner.) Audio 
must be provided by your own...

7
Connecting a video device If your video device has more than one output, select the highest quality 
one. DVI video has the best quality, followed by Component video, S-video, 
and then composite video. 
If the video device uses component cable connectors, plug the cable’s green 
connectors into the green component-out connector on the video device and 
into the green component connector (labeled “Y”) on the projector. Plug the 
component cable’s blue connectors into the blue component-out connector...

8
Displaying a video imageRemove the lens cap. 
Press the Pow e r button on the top of the projector.
The projector chimes if the chime feature is enabled (page 28). The LED 
flashes green and the fans start to run. When the lamp comes on, the startup 
screen displays and the LED is steady green. It can take a minute for the 
image to achieve full brightness. 
? No startup screen? Get help on page 12.
Plug in and turn on the video device.
An image from the video device should appear on the projection...

9
Adjust the zoom or focus rings by rotating them until the desired image size 
and sharpness are produced.
If the image is not square, adjust the keystone using the buttons on the key-
pad. Press the upper Ke y s t o n e  button to reduce the width of the upper por-
tion of the image, and press the lower Ke y s t o n e  button to reduce the width 
of the lower portion.
The Contrast, Brightness, Color, andTint are factory calibrated to D65 col-
ors, but you can adjust these settings in the Picture menu...

10
Connecting a computerConnect either a VESA cable or M1 cable into the appropriate connector on 
the projector. Connect the other end to the video port on your computer. If 
you are using a desktop computer, you first need to disconnect the monitor 
cable from the computer ’s video port. 
Connect the power cable to the connector on the back of the projector and to 
your electrical outlet.
The Power LED on the projector ’s keypad turns solid green.
NOTE: Always use the power cable that shipped with the...