InFocus Projector X6 User Manual
Here you can view all the pages of manual InFocus Projector X6 User Manual. The InFocus manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 31
0English ... Appendices Problem: Image has vertical flickering bar Use “Frequence” to make an adjustment. Check and reconfigure the display mode of your graphic card to make it compatible with the product. Problem: Image is out of focus Adjust the Focus Ring on the projector lens. Make sure the projection screen is between the required distance 3.9 to 39.4 feet (1.2 to 12.0 meters) from the projector (refer to page 16). Problem: The image is stretched when displaying 16:9 DVD...
Page 32
... English Appendices Problem: LED lighting message Steady light => No light => MessagePower-LED (Blue)(Red)(Purple) Standby (Input power cord)Flashing (0.5 sec.) Power on (Warming up) Lamp lighting (Displaying) Power off (Cooling-I) Power off (Cooling-II)Flashing (0.5 sec.) Error (Lamp failed)Flashing (1 sec.) Error (Fan lock)Flashing (0.5 sec.) Error (Over temp.) Standby mode (Lamp failed)Flashing (1 sec.) Standby mode (Fan lock)Flashing (0.5 sec.) Standby mode (Over temp.)
Page 33
2English ... Appendices Problem: Message Reminders Over temperature - the projector has exceeded its recommended operating temperature and must be allowed to cool down before it may be used. Replacing the lamp - the lamp is about to reach its maximum life- time. Prepare to replace it soon. Fan failed - the system fan is not working.
Page 34
... English Appendices Replacing the lamp The projector will detect the lamp life itself. It will show you a warning message Only InFocus lamps are tested with this projector. Use of other lamps may cause electrical shock and fire. Be extremely careful when removing the lamp housing. In the unlikely event that the bulb ruptures, small glass frag- ments may be generated. The lamp housing is designed to contain these fragments, but use caution when remov- ing the lamp housing....
Page 35
English ... Appendices Warning: To avoid burns, allow the projec-tor to cool for at least 60 minutes before you replace the lamp! Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped. Lamp Replacing Procedure: 1. Switch off the power to the projector by pressing the Power/ Standby . 2. Allow the projector to cool down at least 60 minutes. 3. Disconnect the power cord. 4. Use...
Page 36
5... English Appendices Compatibility Modes VGA Analog - PC Signal ModesResolutionV.Frequency(Hz) H.Frequency(kHz) VGA640 x 4806031.50 640 x 4807237.90 640 x 4807537.50 640 x 4808543.30 720 x 4007031.50 720 x 4008537.90 SVGA800 x 6005635.20 800 x 6006037.90 800 x 6007248.10 800 x 6007546.90 800 x 6008553.70 832 x 6247549.725 XGA1024 x 7686048.40 1024 x 7687056.50 1024 x 7687560.00 1024 x 7688568.70 SXGA1152 x 8647063.80 1152 x 8647567.50 *1152 x 8648577.10 1280 x 10246063.98 *1280 x 10247276.97...
Page 37
English ... Appendices ModesResolutionV.Frequency(Hz) H.Frequency(kHz) 640 x 48066.6 (67)34.93 800 x 6006037.90 1024 x 7686048.40 1152 x 8707568.68 *1280 x 9607575.00 i Mac DV (G3)1024 x 7687560.00 Note: “*” for XGA model only