InFocus Projector X6 User Manual

20English ...

User Controls

Image
(Video Mode)
	 Display	Mode
		There	are	many	factory	presets	optimized	for	various	types	of	im-
ages.	
		PC:	For	computer	or	notebook.
		Movie:	For	home	theater.
		sRGB:	For	standard	color.
		Game:	For	game.
		User:	Memorize	user’s	settings.
	 Brightness
	Adjust	the	brightness	of	the	image.
		Press	the		to	darken	image.
		Press	the		to	lighten	the	image.
	 Contrast
	 	The	contrast	controls	the	degree	of	difference	between	the	lightest	
and	darkest	parts	of	the...

2... English

User Controls

	 Color
		Adjust	a	video	imge	from	black	and	white	to	fully	saturated	color.
		Press	the		to	decrease	the	amount	of	color	in	the	image.
		Press	the		to	increase	the	amount	of	color	in	the	image.		
	 Tint
	Adjust	the	color	balance	of	red	and	green.
		Press	the		to	increase	the	amount	of	green	in	the	image.
		Press	the		to	increase	the	amount	of	red	in	the	image.
	 Sharpness
	Adjust	the	sharpness	of	the	image.
		Press	the		to	decrease	the	sharpness.
		Press	the		to...

22English ...

User Controls

Display Setting
	 Keystone
	 Adjust	image	distortion	caused	by	tilting	projector.	(±15	degrees).
	 H-Position	(Horizontal	Position)
		Press	the		to	move	the	image	left.	
		Press	the		to	move	the	image	right.	
	 V-Position	(Vertical	Position)
		Press	the		to	move	the	image	down.
		Press	the		to	move	the	image	up.
	Aspect	Ratio
	Use	this	function	to	choose	your	desired	aspect	ratio.
				4:3	
	 		
This	format	is	for	4x3	input	sources	not	enhanced	for	Wide-
screen	TV.	
	...

2... English

User Controls

	 Projection
				Front-Desktop	
	 	 The	factory	default	setting.	
				Rear-Desktop	
	 		
When	you	select	this	function,	the	projector	reverses	the	image	
so	you	can	project	behind	a	translucent	screen.
				Front-Ceiling	
	 		
When	you	select	this	function,	the	projector	turns	the	image	
upside	down	for	ceiling-mounted	projection.
			 Rear-Ceiling	
	 		
When	you	select	this	function,	the	projector	reverses	and	turns	
the	image	upside	down	at	same	time.	You	can...

2English ...

User Controls

	 Source	Lock
		When	this	function	is	turned	“Off”,	the	projector	will	search	for	
other	signals	if	the	current	input	signal	is	lost.	When	this	function	is	
turned	“On”,	it	will	search	specified	connection	port.
	 Fan	Control
	
Choose	“On”	to	turn	on	Fan	Control	mode.	Operate	the	fan	at	full	
speed	continuously	to	allow	for	proper	high	altitude	cooling	of	the	
projector.
	 Lamp	Reminding
	 	
Choose	this	function	to	show	or	to	hide	the	warning	message	when	
the	changing...

25... English

User Controls

	 Audio
			
	Mute:
		Choose	“On”	to	mute	the	volume.	
		Choose	“Off”	to	restore	the	volume.	
	Volume:
		Press	the		to	decrease	the	volume.	
		Press	the		to	increase	the	volume.
	 Lamp	Reset
	Reset	the	lamp	life	hour	after	replacing	a	new	lamp.	
	 Reset
	Return	the	adjustments	and	settings	to	the	factory	default	values.
	
	 

2English ...

User Controls

	 Language
	
Choose	the	multilingual	OSD	menu.	Press		into	the	sub	menu	and	
then	use	the		or		or		or		key	to	select	your	preferred		
language.	Press	“Enter”	to	finalize	the	selection.	
Language 

27... English

User Controls

	 Information
	To	display	the	projector	information	on	the	screen.
Information 

28English ...

Appendices

Problem: No image appears on screen
		Ensure	all	the	cables	and	power	connections	are	correctly	and	
securely	connected	as	described	in	the	“Operation”	section.
	Ensure	the	pins	of	connectors	are	not	crooked	or	broken.
		Check	if	the	projection	lamp	has	been	securely	installed.	Please	
refer	to	the	“Replacing	the	lamp”	section.
		Make	sure	you	have	removed	the	lens	cap	and	the	projector	is	
switched	on.
Problem: Partial, scrolling or incorrectly displayed image
	Press...

2... English

Appendices

	 4.		
Verify	the	resolution	setting	is	less	than	or	equal	to	1280	x	1024	
resolution.
	 5.	 Select	the	“Change”		under	the	“Monitor”	tab	.
	 6.		
Click	on	“Show	all	devices”.	Next,	select	“Standard	monitor	
types”	under	the	SP	box;	choose	the	resolution	mode	you	need	
under	the	“Models”	box.	
	 If	you	are	using	a	Notebook:
	 1.		
First,	follow	the	steps	above	to	adjust	resolution	of	the	com-
puter.
	 2.	 Press	the	toggle	output	settings.	example:	[Fn]+[F4]
	 	
		
If	you...