InFocus Projector X6 User Manual

0English ...
Introduction
5Keystone		
Correction
Adjust	the	image	to	compensate	
for	distortion	caused	by	tilt-
ing	the	projector	(vertical	±	15	
degrees).
6SourcePress	“source”	to	choose	RGB,	
Component,	S-Video,	Composite	
and	HDTV	sources.
7MenuPress	“menu”	to	launch	the	On-
screen	display	(OSD)	menu,	back	
to	the	top	level	of	OSD	menu	for	
the	OSD	main	menu	operation
8AV-MuteMomentarily	turn	off/on	the	
audio	and	video.
9ResetChange	the	adjustments	and	set-
tings	to	the	factory	default...

... English
Operation
Connecting the Projector
	Due	to	the		 	difference	in		 	applications	for	each		country,	some	regions	may	have	different	 	accessories.
		To	ensure	the	projector	works	well	with	your	computer,	
please	make	sure	the	timing	of	the	display	mode	is	
compatible	with	your	projector.
1.........................................................................\
.......................................Power...

2English ...

Operation

Powering On the Projector
1.	 Remove	the	lens	cap.	
2.		
Ensure	that	the	power	cord	and	signal	cable	are	securely	
connected.	The	Power	LED	will	turn	flash	blue.
3.		
Turn	on	the	lamp	by	pressing	“Power/Standby”		on	the	
control	panel.		The	startup	screen	will	display	for	about	25	
seconds	and	the	Power	LED	will	turn	blue.
4.		
Turn	on	your	source	(computer,	notebook,	video	player,etc.)	
The	projector	will	detect	your	source	automatically.
		If	you	connect	multiple...

... English

Operation

Powering Off the Projector
1.			
Press	the	“Power/Standby”		to	turn	off	the	projector	lamp,	
you	will	see	a	message	as	below	on	the	on-screen	display.
	
2.		Press	the	“Power/Standby”		again	to	confirm.	
3.		
The	cooling	fan	continues	to	operate	for	about	120	seconds	
for	cooling	cycle	and	the	Power	LED	will	flash	blue.	When	
the	light	starts	flashing,	the	projector	has	entered	standby	
mode.
		
If	you	wish	to	turn	the	projector	back	on,	you	must	wait	
until	the...

English ...

Operation

Warning Indicator
		
When	the	“Power”	LED	indicator	turns	red,	it	indicates	the	
projector	has	overheated.	The	projector	will	automatically	
shut	itself	down.
		
When	the	“Power”	LED	indicator	flashes	red	and	the	mes-
sage	below	displays	onscreen,	it	indicates	the	projector	
will	detect	the	lamp	life	itself.	When	you	see	this	message,	
change	the	lamp	as	soon	as	possible	or	contact	your	local	
dealer	or	our	service	center.	
		
When	the	“Power”	LED	indicator	flashes...

5... English

Operation

Adjusting the Projected Image
Adjusting the Height of Projector Image
The projector is equipped with elevator feet for adjusting the 
height of image.
	To	raise/lower	the	image:
1.	 Use		to	fine-tune	the	display	angle.
TiltadjustingwheelTiltadjustingwheel 

English ...
Operation...

7... English
User Controls
The Projector has multilingual On Screen Display menus that 
allow you to make image adjustments and change a variety of 
settings. The projector will automatically detect the source. 
How to operate 
1.	 To	open	the	OSD	menu,	press	“Menu”	on	the	Remote	Control.
2.		When	OSD	is	displayed,	use						keys	to	select	any	item	in	the	
main	menu.	While	making	a	selection	on	a	particular	page,	press		
		key	to	enter	sub	menu.
3.	 	Use						keys	to	select	the	desired	item	in	the...

8English ...

User Controls

Image
(PC Mode)
	 Display	Mode
		There	are	many	factory	presets	optimized	for	various	types	of	im-
ages.		
		PC:	For	computer	or	notebook.
		Movie:	For	home	theater.
		sRGB:	For	standard	color.
		Game:	For	game.
		User:	Memorize	user’s	settings.
	 Brightness
	Adjust	the	brightness	of	the	image.
		Press	the		to	darken	image.
		Press	the		to	lighten	the	image.
	 Contrast
	 	The	contrast	controls	the	degree	of	difference	between	the	lightest	
and	darkest	parts	of...

... English

User Controls

	 Frequence
		“Frequence”	changes	the	display	data	frequency	to	match	the	fre-
quency	of	your	computer’s	graphic	card.	If	you	experience	a	vertical	
flickering	bar,	use	this	function	to	make	an	adjustment.
	 Tracking
		Synchronize	the	signal	timing	of	the	projector	with	the	graphics	
card.	If	you	experience	an	unstable	or	flickering	image,	use	this	
function	to	correct	it.	
	 White	Peaking
		Use	the	white	peaking	control	to	set	the	white	peaking	level	of	
DMD	chip....