Home > InFocus > Projector > InFocus Projector X17 User Manual

InFocus Projector X17 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual InFocus Projector X17 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 493 InFocus manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Operation 41
    FUNCTION
    (default setting/
    value)DESCRIPTION (default setting/value)
    Closed 
    Caption
    Closed Caption Enable (Off)
    Activates the function by selecting On when the selected input 
    signal carries closed captions.
    • Captions: An on-screen display of the dialogue, narration, 
    and sound effects of TV programs and videos that are 
    closed captioned (usually marked as CC in TV listings).
    Caption Version (CC1)
    Selects a preferred closed captioning mode. To view captions, 
    select CC1, CC2, CC3, or CC4 (CC1 displays captions in the 
    primary language in your area).
    VGA Out
    (Off)Selecting On enables the function. The projector can output a 
    VGA signal when it is in standby mode and the D-SUB IN and 
    D-SUB OUT sockets are correctly connected to devices. See 
    Connecting a monitor on page 14 for how to make the 
    connection.
    Enabling this function slightly increases the standby power 
    consumption.
    Lamp 
    Settings
    Lamp mode (Normal)
    See Setting Lamp mode as Economic on page 44 for details.
    Reset lamp timer
    See Resetting the lamp timer on page 48 for details.
    Equivalent lamp hour
    S
    ee Getting to know the lamp hour on page 44 for details 
    on how the total lamp hour is calculated.
    Security 
    Settings
    Change password
    You will be asked to enter the current password before 
    changing to a new one.
    Power on lock (Off)
    See Utilizing the password function on page 21 for details.
    Reset All 
    SettingsReturns all settings to the factory preset values.
    The following settings will still remain: Position, Phase, H. Size, 
    User 1, User 2, Language, Projector Position, High Altitude 
    Mode, Security Settings.
    5. SYSTEM SETUP: Advanced menu 
    						
    							Operation 42
    FUNCTION
    (default setting/
    value)DESCRIPTION (default setting/value)
    Current 
    System 
    Status
    Source
    Shows the current signal source.
    Preset Mode
    Shows the selected mode in the PICTURE menu.
    Resolution
    Shows the native resolution of the input signal.
    Color System
    Shows input system format, NTSC, PAL, SECAM, or RGB.
    Equivalent Lamp Hour
    Displays the number of hours the lamp has been used.6. INFORMATION menu 
    						
    							Maintenance 43
    Maintenance
    Care of the projector
    Your projector needs little maintenance. The only thing you need to do on a regular 
    basis is to keep the lens clean.
    Never remove any parts of the projector except the lamp. Contact your dealer if 
    other parts need replacing.
    Cleaning the lens
    Clean the lens whenever you notice dirt or dust on the surface. 
    • Use a canister of compressed air to remove dust. 
    • If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with 
    lens cleaner and gently wipe the lens surface.
    CAUTION
    Never rub the lens with abrasive materials.
    Cleaning the projector case
    Before you clean the case, turn the projector off using the proper shutdown 
    procedure as described in Shutting down the projector on page 35 and unplug the 
    power cord.
    • To remove dirt or dust, wipe the case with a soft, lint-free cloth.
    • To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral 
    pH detergent. Then wipe the case.
    CAUTION
    Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the 
    case.
    Storing the projector
    If you need to store the projector for an extended time, please follow the 
    instructions below:
    • Make sure the temperature and humidity of the storage area are within the 
    recommended range for the projector. Please refer to Specifications on page 
    51 or consult your dealer about the range.
    • Retract the adjuster feet.
    • Remove the battery from the remote control.
    • Pack the projector in its original packing or equivalent.
    Transporting the projector
    It is recommended that you ship the projector with its original packing or equivalent. 
    						
    							Maintenance 44
    Lamp information
    Getting to know the lamp hour
    When the projector is in operation, the duration (in hours) of lamp usage is 
    automatically calculated by the built-in timer. The method of calculating the 
    equivalent lamp hour is as follows:
    Total (equivalent) lamp hour
    = 1 (hours used in Economic mode) + 4/3 (hours used in Normal mode)
    See Setting Lamp mode as Economic below for more information on Economic mode.
    The lamp hour in Economic mode is calculated as 3/4 of that in Normal mode. 
    That is, using the projector in Economic mode helps to extend the lamp hour by 1/
    3.
    To obtain the lamp hour information:
    1. Press MENU/EXIT and then press  /  until the SYSTEM SETUP: 
    Advanced menu is highlighted.
    2. Press  to highlight Lamp Settings and press MODE/ENTER. The Lamp 
    Settings page displays.
    3. You will see the Equivalent lamp hour information displaying on the menu.
    4. To leave the menu, press MENU/EXIT.
    You can also get the lamp hour information on the INFORMATION menu.
    Extending lamp life
    The projection lamp is a consumable item that normally can last up to 3000-4000 
    hours with proper usage. To keep the lamp life as long as possible, you can do the 
    following settings via the OSD menu.
    Setting Lamp mode as Economic
    Using Economic mode reduces system noise and power consumption by 20%. If 
    the Economic mode is selected, the light output will be reduced and result in 
    darker projected pictures.
    Setting the projector in Economic mode also extends the lamp operation life. To 
    set Economic mode, go into the SYSTEM SETUP: Advanced > Lamp Settings > 
    Lamp mode menu and press  / .
    Setting Auto Power Off
    This function allows the projector to turn off automatically if no input source is 
    detected after a set period of time to prevent unnecessary waste of lamp life.
    To set Auto Power Off, go into the SYSTEM SETUP: Basic > Auto Power Off 
    menu and press  / . The time period can be set from 5 to 30 minutes in 5-minute 
    increments. If the preset time lengths are not suitable for your presentation, select 
    Disable. The projector will not automatically shut down in a certain time period. 
    						
    							Maintenance 45
    Timing of replacing the lamp
    When the Lamp indicator lights up red or a message appears suggesting it is time 
    to replace the lamp, please install a new lamp or consult your dealer. An old lamp 
    may cause a malfunction in the projector and in some instances the lamp may 
    explode.
    CAUTION
    The Lamp indicator light and Temperature warning light will light up if the lamp becomes too 
    hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator 
    still lights up after turning the power back on, please contact your dealer. See Indicators on 
    page 49 for details.
    The following lamp warning displays will remind you to change the lamp.
    StatusMessage
    The lamp has been in operation for 3000 
    hours. Install a new lamp for optimal 
    performance. If the projector is normally run 
    with Economic selected (See Setting Lamp 
    mode as Economic on page 44), you may 
    continue to operate the projector until the 
    3950 hour lamp warning appears.
    The lamp has been in operation for 3950 
    hours. A new lamp should be fitted to avoid 
    the inconvenience when the projector runs 
    out of lamp time.
    The lamp has been in operation for 4000 
    hours.
    It is strongly recommended that you replace 
    the lamp at this age. The lamp is a 
    consumable item. The lamp brightness 
    diminishes with use. This is normal lamp 
    behavior. You can replace the lamp whenever 
    you notice that the brightness level has 
    significantly diminished. If the lamp is not 
    replaced beforehand, it must be replaced 
    after 4000 hours usage.
    The lamp MUST be replaced before the 
    projector will operate normally.
    OK
    Order Replacement Lamp
    Lamp > 3000 Hours
    Notice
    OK
    Replace Lamp Soon 
    Lamp > 3950 Hours
    Notice
    OK
    Replace Lamp Now 
    Lamp > 4000 Hours
    Lamp usage time exceeded
    Notice
    OK
    Lamp-usage time exceeded
    Replace lamp (refer to Reference Guide)
    Then reset lamp timer
    Notice 
    						
    							Maintenance 46
    Replacing the lamp
    WARNING
    Hg - Lamp contains mercury. Manage in accordance with local 
    disposal laws. See www.lamprecycle.org
    • To reduce the risk of electrical shock, always turn the projector off and disconnect the 
    power cord before changing the lamp.
    • To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes 
    before replacing the lamp.
    • To reduce the risk of injuries to fingers and damage to internal components, use caution 
    when removing lamp glass that has shattered into sharp pieces. Before replacing the 
    lamp, clean the lamp compartment and dispose of cleaning materials. Be careful of sharp 
    edges in the lamp compartment. Wash hands after lamp replacement.
    • Only InFocus certified lamps are tested with this projector.  Use of other lamps may cause 
    electrical shock and fire.
    1. Turn the power off and disconnect 
    the projector from the wall socket. If 
    the lamp is hot, avoid burns by 
    waiting for approximately 45 
    minutes until the lamp has cooled.
    2. Turn the projector over. Then 
    loosen the screws on the lamp 
    cover.
    3. Remove the lamp cover from the 
    projector.
    WARNING
    • Do not turn the power on with the lamp 
    cover removed.
    • Do not insert your fingers between the 
    lamp and the projector. The sharp edges 
    inside the projector may cause injuries.
    4. Loosen the screw that secures the 
    lamp. 
    						
    							Maintenance 47 5. Pull out the lamp connector from a 
    slot in the lamp compartment. 
    Disconnect it from the projector as 
    illustrated.
    6. Lift the handle so that it stands up. 
    Use the handle to slowly pull the 
    lamp out of the projector.
    CAUTION
    • Pulling it too quickly may cause the lamp 
    to break and scatter broken glass in the 
    projector.
    • Do not place the lamp in locations where 
    water might splash on it, children can 
    reach it, or near flammable materials.
    • Do not insert your hands into the projector 
    after the lamp is removed. If you touch the 
    optical components inside, it could cause 
    color unevenness and distortion of the 
    projected images.
    7. Insert the new lamp into the 
    lamp compartment and 
    make sure it fits in the 
    projector.
    8. Reconnect the lamp 
    connector and place it back 
    into its slot to be flush with 
    the projector.
    1
    2
    2 
    						
    							Maintenance 4813. Restart the projector.
    CAUTION
    Do not turn the power on with the lamp cover removed.
    Resetting the lamp timer
    14. After the startup logo, open the On-
    Screen Display (OSD) menu. Go to the 
    SYSTEM SETUP: Advanced > Lamp 
    Settings menu. Press MODE/ENTER. 
    The Lamp Settings page displays. 
    Press  to highlight Reset lamp timer 
    and press MODE/ENTER. A warning message displays asking if you want to 
    reset the lamp timer. Highlight Reset and press MODE/ENTER. The lamp 
    time will be reset to 0.
    CAUTION
    Do not reset if the lamp is not new or replaced as this could cause damage. 
    9. Tighten the screw that secures the 
    lamp.
    CAUTION
    • Loose screw may cause a bad connection, 
    which could result in malfunction.
    • Do not over tighten the screw.
    10. Ensure the handle is fully laid flat 
    and locked in place.
    11. Replace the lamp cover on the 
    projector.
    12. Tighten the screws that secure the 
    lamp cover.
    CAUTION
    • Loose screw may cause a bad connection, 
    which could result in malfunction.
    • Do not over tighten the screws.
    Reset Lamp Timer?
    Reset
    Cancel
    Notice 
    						
    							Maintenance 49
    Indicators
    LightStatus & Description
    PowerTe m pLamp
    Power events
    Orange Orange OrangeThe projector has just been connected to a power 
    outlet.
    Orange Off OffStand-by mode
    Green
    FlashingOff OffPowering up
    Green Off OffNormal operation
    Orange
    FlashingOff Off
    1. The projector needs 90 seconds to cool down as it 
    was abnormally shut down without the normal 
    cooling down process. Or
    2. The projector needs to cool for 90 seconds after 
    the power is turned off.
    Orange
    FlashingOff OffThe projector has shutdown automatically. If you try to 
    re-start the projector, it will shutdown again. Please 
    contact your dealer for assistance.
    Lamp events
    Orange
    FlashingOff RedThe projector has shutdown automatically. If you try to 
    re-start the projector, it will shutdown again. Please 
    contact your dealer for assistance.
    Off Off Red1. The projector needs 90 seconds to cool down. Or
    2. Please contact your dealer for assistance.
    Thermal events
    Off Red Off
    The projector has shutdown automatically. If you try to 
    re-start the projector, it will shutdown again. Please 
    contact your dealer for assistance.
    Off Red Red
    Off Red Green
    Off Red Orange
    Red Red Red
    Red Red Green
    Red Red Orange
    Green Red Red
    Green Red Green
    Green Red Orange
    Orange Red Red
    Orange Red Green
    Orange Red Orange
    Off Green Red
    Off Green Green 
    						
    							Troubleshooting 50
    Troubleshooting
    The projector does not turn on.
    No picture
    Blurred image
    Remote control does not work
    The password is incorrect
    CauseRemedy
    There is no power from the power 
    cable.Plug the power cord into the AC inlet on the 
    projector, and plug the power cord into the 
    power outlet. If the power outlet has a switch, 
    make sure that it is switched on.
    Attempting to turn the projector on 
    again during the cooling process.Wait until the cooling down process has 
    completed.
    CauseRemedy
    The video source is not turned on or 
    connected correctly.Turn the video source on and check that the 
    signal cable is connected correctly.
    The projector is not correctly 
    connected to the input signal device.Check the connection.
    The input signal has not been 
    correctly selected.Select the correct input signal with the 
    SOURCE key on the projector or remote 
    control.
    The lens cover is still closed. Open the lens cover.
    CauseRemedy
    The projection lens is not correctly 
    focused.Adjust the focus of the lens using the focus 
    ring.
    The projector and the screen are not 
    aligned properly.Adjust the projection angle and direction as 
    well as the height of the unit if necessary.
    The lens cover is still closed. Open the lens cover.
    CauseRemedy
    The battery is out of power. Replace the battery with new one.
    There is an obstacle between the 
    remote control and the projector.Remove the obstacle.
    You are too far away from the 
    projector.Stand within 8 meters (26 feet) of the 
    projector.
    CauseRemedy
    You do not remember the password.Please see Entering the password recall 
    procedure on page 22 for details. 
    						
    All InFocus manuals Comments (0)

    Related Manuals for InFocus Projector X17 User Manual