InFocus Projector X17 User Manual
Have a look at the manual InFocus Projector X17 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 493 InFocus manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Operation 31 3D Color Management In most installation situations, color management will not be necessary, such as in classroom, meeting room, or lounge room situations where lights remain on, or where building external windows allow daylight into the room. Only in permanent installations with controlled lighting levels such as boardrooms, lecture theaters, or home theaters, should color management be considered. 3D Color Management provides fine color control adjustment to allow for more accurate color reproduction, should you require it. Proper color management can only be achieved under controlled and reproducible viewing conditions. You will need to use a colorimeter (color light meter), and provide a set of suitable source images to measure color reproduction. These tools are not provided with the projector, however, your projector supplier should be able to provide you with suitable guidance, or even an experienced professional installer. 3D Color Management provides six sets (RGBCMY) of colors to be adjusted. When you select each color, you can independently adjust its range and saturation according to your preference. If you have purchased a test disc which contains various color test patterns and can be used to test the color presentation on monitors, TVs, projectors, etc. You can project any image from the disc on the screen and enter the 3D Color Management menu to make adjustments. To adjust the settings: 1. Go to the PICTURE menu and highlight 3D Color Management. 2. Press MODE/ENTER and the 3D Color Management page displays. 3. Highlight Primary Color and press / to select a color from among Red, Yellow, Green, Cyan, Blue, or Magenta. 4. Press to highlight Hue and press / to select its range. Increase in the range will include colors consisted of more proportions of its two adjacent colors. Please refer to the illustration to the right for how the colors relate to each other. For example, if you select Red and set its range at 0, only pure red in the projected picture will be selected. Increasing its range will include red close to yellow and red close to magenta. 5. Press to highlight Saturation and adjust its values to your preference by pressing / . Every adjustment made will reflect to the image immediately. For example, if you select Red and set its value at 0, only the saturation of pure red will be affected. 6. Press to highlight Gain and adjust its values to your preference by pressing / . The contrast level of the primary color you select will be affected. Every adjustment made will reflect to the image immediately. 7. Repeat steps 3 to 6 for other color adjustments. 8. Make sure you have made all of the desired adjustments. RED BLUEGREEN Yellow Cyan Magenta
Operation 329. Press MENU/EXIT to exit and save the settings. Saturation is the amount of that color in a video picture. Lower settings produce less saturated colors; a setting of “0” removes that color from the image entirely. If the saturation is too high, that color will be overpowering and unrealistic. Setting the presentation timer The presentation timer can indicate the presentation time on the screen to help you achieve better time management when giving presentations. Follow these steps to utilize this function: 1. Go to the SYSTEM SETUP: Basic > Presentation Timer menu and press MODE/ENTER to display the Presentation Timer page. 2. Highlight Timer Period and decide the time period by pressing / . The length of time can be set from 1 to 5 minutes in 1-minute increments and 5 to 240 minutes in 5-minute increments. If the timer is already on, the timer will restart whenever the Timer Period is reset. 3. Press to highlight Timer Display and choose if you want the timer to show up on the screen by press ing /. 4. Press to highlight Timer Position and set the timer position by pressing / . Top-Left Bottom-Left Top-Right Bottom-Right 5. Press to highlight Timer Counting Direction and select your desired counting direction by pressing / . 6. Press to highlight Sound Reminder and decide if you want to activate sound reminder by pressing / . If you select On, a double beep sound will be heard at the last 30 seconds of counting down/up, and a triple beep sound will be produced when the timer is up. 7. To activate the presentation timer, press and press / to highlight On and press MODE/ENTER. 8. A confirmation message displays. Highlight Yes and press MODE/ENTER to confirm. You will see the message “Timer is On” displaying on the screen. The timer starts counting at the time the timer is on. SelectionDescription Always Displays the timer on screen throughout the presentation time. 1 min/2 min/3 min Displays the timer on screen in the last 1/2/3 minute(s). Never Hides the timer throughout the presentation time. SelectionDescription Count UpIncreases from 0 to the preset time. Count DownDecreases from the preset time to 0. Presentation Timer Timer Display Timer Position Timer Counting Direction Sound ReminderAlways Top-Left Count Down Off On Off MENU Back Timer Period 15
Operation 33 To cancel the timer, perform the following steps. 1. Enter the SYSTEM SETUP: Basic > Presentation Timer menu and highlight Off. Press MODE/ENTER. A confirmation message displays. 2. Highlight Yes and press MODE/ENTER to confirm. You will see the message “Timer is Off” displaying on the screen. Hiding the image In order to draw the audiences full attention to the presenter, you can use BLANK on the projector or remote control to hide the screen image. Press any key on the projector or remote control to restore the image. The word BLANK appears at the lower right corner of the screen while the image is hidden. You can set the blank time in the SYSTEM SETUP: Basic > Blank Timer menu to let the projector return the image automatically after a period of time when there is no action taken on the blank screen. Once BLANK is pressed, the projector enters Economic mode automatically. CAUTION Do not block the projection lens from projecting as this could cause the blocking object to become heated and deformed or even cause a fire. Locking control keys With the control keys on the projector locked, you can prevent your projector settings from being changed accidentally (by children, for example). When the Panel Key Lock is on, no control keys on the projector will operate except POWER. 1. Press / on the projector or remote control or go to the SYSTEM SETUP: Basic > Panel Key Lock menu , and select On by pressing / on the projector or remote control. 2. A confirmation message displays. Select Yes to confirm. To release panel key lock, press and hold / for 3 seconds on the projector or remote control. You can also use the remote control to enter the SYSTEM SETUP: Basic > Panel Key Lock and press / to select Off. • Keys on the remote control are still in use when panel key lock is enabled. • If you press POWER to turn off the projector without disabling panel key lock, the projector will still be in locked status the next time it is turned on. II / O G O L e m a N l e d o M a e r A35.0 mmm m 0 . 5 4 II
Operation 34 Freezing the image Press on the remote control to freeze the image. The word FREEZE will display in the upper left corner of the screen. To release the function, press any key on the projector or remote control. Even if an image is frozen on the screen, the pictures are running on the video or other device. If the connected devices have active audio output, you will still hear the audio even though the image is frozen on screen. Operating in a high altitude environment We recommend you use the High Altitude Mode when your environment is between 1500 m–3000 m above sea level, and temperature is between 0°C–35°C. CAUTION Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and temperature is between 0°C and 35°C. The projector will be over cooled, if you turn the mode on under such condition. To activate the High Altitude Mode: 1. Press MENU/EXIT and then press / until the SYSTEM SETUP: Advanced menu is highlighted. 2. Press to highlight High Altitude Mode and press / to select On. A confirmation message displays. 3. Highlight Yes and press MODE/ENTER. Operation under High Altitude Mode may cause a higher decibel operating noise level because of increased fan speed necessary to improve overall system cooling and performance. If you use this projector under other extreme conditions excluding the above, it may display auto shut-down symptoms, which is designed to protect your projector from over-heating. In cases like this, you should switch to High Altitude Mode to solve these symptoms. However, this is not to state that this projector can operate under any and all harsh or extreme conditions. Adjusting the sound The sound adjustments made as below will have an effect on the projector speaker. Be sure you have made a correct connection to the projector audio input. See Connection on page 13 for how the audio input is connected. Muting the sound To temporarily turn off the sound: 1. Press MENU/EXIT and then press / until the SYSTEM SETUP: Advanced menu is highlighted. 2. Press to highlight Audio Settings and press MODE/ENTER. The Audio Settings page displays. 3. Highlight Mute and press / to select On. We recommend you use the High Altitude Mode by selecting it whenever your environment is higher than 1500 m. Do you want to turn the High Altitude Mode on? YesNo WARNING
Operation 35 Adjusting the sound level To adjust the sound level: 1. Repeat steps 1-2 above. 2. Press to highlight Volume and press / to select a desired sound level. Personalizing the projector menu display The On-Screen Display (OSD) menus can be set according to your preferences. The following settings do not affect the projection settings, operation, or performance. •Menu display time in the SYSTEM SETUP: Advanced > Menu Settings menu sets the length of time the OSD will remain active after your last key press. The time length ranges from 5 to 30 seconds in 5-second increments. Use / to select a suitable time frame. •Menu position in the SYSTEM SETUP: Advanced > Menu Settings menu sets the OSD position in five locations. Use / to select a preferred position. •Language in the SYSTEM SETUP: Basic menu sets your familiar language for the OSD menus. Use / to select your language. •Splash Screen in the SYSTEM SETUP: Basic menu sets a preferred logo screen to be displayed during projector start-up. Use / to select a screen. Shutting down the projector 1. Press POWER and a confirmation message displays prompting you. If you dont respond in a few seconds, the message will disappear. 2. Press POWER a second time. The POWER indicator light flashes orange, the projection lamp shuts down, and the fans will continue to run for approximately 90 seconds to cool down the projector. 3. The POWER indicator light is a steady orange and fans stop. 4. Disconnect the power cord from the wall socket if the projector will not be used in an extended period of time. CAUTION • To protect the lamp, the projector will not respond to any commands during the cooling process. • To shorten the cooling time, you can also activate the Quick Cooling function. See Quick Cooling on page 40 for details. • Do not unplug the power cord before the projector shutdown sequence is complete or during the 90-second cooling down process. • If the projector is not properly shut down, to protect the lamp, when you attempt to re-start the projector, the fans will run for a few minutes to cool down. Press POWER again to start the projector after the fans stop and the POWER indicator light turns orange. II II II
Operation 36 Menu operation Menu system Please note that the on-screen display (OSD) menus vary according to the signal type selected. The menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible. Main menu Sub-menu Options 1. DISPLAY Wall ColorOff/Light Yellow/Pink/Light Green/Blue/Blackboard Aspect Ratio Auto/Real/4:3/16:9 Keystone Position Phase H. Size Digital Zoom 2. PICTURE Preset ModePC source: Brightest/Presentation/Photo/Cinema/ User 1/User 2 Video source: Brightest/Standard/Cinema/User 1/ User 2 Reference ModePC source: Brightest/Presentation/Photo/Cinema Video source: Brightest/Standard/Cinema Brightness Contrast Color Tint Sharpness Brilliant Color On/Off Color TemperatureT1/T2/T3/T4 3D Color ManagementPrimary ColorR/G/B/Y/C/M Hue Saturation Gain Save Settings 3. SOURCEQuick Auto Search On/Off 4. SYSTEM SETUP: Basic Presentation TimerTimer Period1~240 minutes Timer DisplayAlways/1 min/2 min/3 min/Never Timer PositionBottom-right/Top-right/Bottom- left/Top-left Timer Counting DirectionCount Down/Count Up Sound Reminder On/Off On/Off
Operation 37 4. SYSTEM SETUP: Basic Language Projector PositionFront Table/Rear Table/Rear Ceiling/Front Ceiling Auto Power OffDisable/5 min/10 min/15 min/20 min/25 min/30 min Blank TimerDisable/5 min/10 min/15 min/20 min/25 min/30 min Panel Key Lock On/Off Timer ControllerDisable/30 min/1 hr/2 hr/3 hr/4 hr/8 hr/12 hr Splash ScreenBlack/Blue/InFocus 5. SYSTEM SETUP: Advanced Quick Cooling On/Off High Altitude Mode On/Off Audio SettingsMute On/Off Volume Menu SettingsMenu display time5 sec/10 sec/15 sec/20 sec/25 sec/30 sec Menu positionCenter/Top-left/Top-right/Bottom- right/Bottom-left Closed CaptionClosed Caption EnableOn/Off Caption VersionCC1/CC2/CC3/CC4 VGA Out On/Off Lamp SettingsLamp mode Normal/Economic Reset lamp timer Equivalent lamp hour Security SettingsChange password Power on lock On/Off Reset All Settings 6. INFORMATI ON Current System Status•Source •Preset Mode •Resolution •Color System •Equivalent Lamp Hour
Operation 38 Description of each menu FUNCTION (default setting/ value)DESCRIPTION (default setting/value) Wall Color (Off)Corrects the projected picture’s color when the projection surface is not white. See Using Wall Color on page 29 for details. Aspect Ratio (Auto)There are four options to set the images aspect ratio depending on your input signal source. See Selecting the aspect ratio on page 26 for details. Keystone (0)Corrects any keystoning of the image. See Correcting keystone on page 25 for details. Position (0)Displays the position adjustment page. To move the projected image, use the directional arrow keys. The values shown on the lower position of the page change with every key press you made until they reach their maximum or minimum. Phase (depends on the selected input signal)Adjusts the clock phase to reduce image distortion. H. Size (0)Adjusts the horizontal width of the image. Digital Zoom (1.0X)Magnifies or reduces the projected image. See Magnifying and searching for details on page 26 for details. Preset Mode (PC source: Brightest; Video source: Standard)Pre-defined picture modes are provided so you can optimize your projector image set-up to suit your program type. See Selecting a picture mode on page 28 for details. Reference Mode (Brightest)Selects a picture mode that most suits your need for the image quality and further fine-tune the image based on the selections listed on the same page below. See Setting the User 1/User 2 mode on page 29 for details. Brightness (50)Adjusts the brightness of the image. See Adjusting Brightness on page 29 for details. Contrast (0)Adjusts the degree of difference between dark and light in the image. See Adjusting Contrast on page 29 for details. Color (0)Adjusts the color saturation level -- the amount of each color in a video image. See Adjusting Color on page 30 for details. 1. DISPLAY menu 2. PICTURE menu
Operation 39 FUNCTION (default setting/ value)DESCRIPTION (default setting/value) Tint (0)Adjusts the red and green color tones of the image. See Adjusting Tint on page 30 for details.The function is only available when Video or S-Video with NTSC system is selected. Sharpness (15)Adjusts the image to make it look sharper or softer. See Adjusting Sharpness on page 30 for details. Brilliant Color (On)Adjusts white peaking while maintaining correct color presentation. See Adjusting Brilliant Color on page 30 for details. Color Temperature (T1)See Selecting a Color Temperature on page 30 for details. 3D Color ManagementSee 3D Color Management on page 31 for details. Save SettingsSaves the settings made for User 1 or User 2 mode. Quick Auto Search (On)See Switching input signal on page 23 for details. Presentation Timer (Off)Reminds the presenter to finish the presentation within a certain time frame. See Setting the presentation timer on page 32 for details. Language (English)Sets the language for the On-Screen Display (OSD) menus. See Using the menus on page 20 for details. Projector Position (Front Table)The projector can be installed on a ceiling or behind a screen, or with one or more mirrors. See Choosing a location on page 9 for details. Auto Power Off (Disable)Allows the projector to turn off automatically if no input signal is detected after a set period of time. See Setting Auto Power Off on page 44 for details. 2. PICTURE menu 3. SOURCE menu4. SYSTEM SETUP: Basic menu
Operation 40 FUNCTION (default setting/ value)DESCRIPTION (default setting/value) Blank Timer (Disable)Sets the image blank time when the Blank feature is activated, once elapsed the image will return to the screen. See Hiding the image on page 33 for details. Panel Key Lock (Off)Disables or enables all panel key functions except POWER on the projector and keys on the remote control. See Locking control keys on page 33 for details. Timer Controller (Disable)Sets the auto-shutdown timer. The timer can be set to a value between 30 minutes and 12 hours. Splash Screen (InFocus logo)Allows you to select which logo screen will display during projector start-up. Three options are available: InFocus logo, Black screen, or Blue screen. Quick Cooling (On)Selecting On enables the function and the projector cooling time will be shortened to a few seconds.If you attempt to restart the projector right after the quick cooling process, it may not be turned on successfully and will rerun its cooling fans. High Altitude Mode (Off)A mode for operation in high altitude areas. See Operating in a high altitude environment on page 34 for details. Audio SettingsMute (Off) Volume (5) See Adjusting the sound on page 34 for details. Menu Settings Menu display time (15 sec) Sets the length of time the OSD will remain active after your last key press. The range is from 5 to 30 seconds in 5-second increments. Menu position (Center) Sets the On-Screen Display (OSD) menu position. 4. SYSTEM SETUP: Basic menu II 5. SYSTEM SETUP: Advanced menu