InFocus Projector Play Big In82 User Manual

10
 Adjust the zoom and focus. If the image is not square, adjust the keystone using the Picture menu. See 
page
 20 
for details.Adjust the volume on your stereo receiver. Your projector has been factory optimized for very good performance no matter 
what the source. However, if you wish to make further changes you can optimize 
the image using onscreen menus. Adjust the Contrast, Brightness, Color, Tint, or 
Aspect Ratio in the Picture menu. See 
page
 20 for help with the menus and these...

11
Shutting down the projectorPower SaveThe projector also has a Power Save feature that automatically turns the lamp off 
after no active sources are detected and no user interaction with the projector is 
performed for 20 minutes. By default, this feature is on. See 
page
 24.
Sleep TimerThe projector also has a sleep timer feature that automatically turns the projector 
off after 4 hours. See 
page
 24.
Turning off the projectorPress the Pow e r button on the remote to turn the projector off. The lamp...

12
Problem 
Solution
Result
no start up screen
plug power cord in back of projector
 
press power button on remote
correct image
only start up screen appears
connect active sourcepress the Source button 
 
 image projected
press power button
Video
Image
K1 RG.fm  Page 12  Thursday, September 27, 2007  10:24 AM 

13
Problem 
Solution
Result
image not centered on screen
move projector, adjust zoom, adjust height
correct image
image not square
Adjust Keystone in Picture menu. If using in tabletop mode, tilt the projector up or 
down.
square image
K1 RG.fm  Page 13  Thursday, September 27, 2007  10:24 AM 

14
image not sharp
Adjust focus or adjust Sharpness in the Picture>Advanced menu
correct image
image upside down
turn off ceiling in Settings>System menu
correct image
ABAB
AB
AB
AB
K1 RG.fm  Page 14  Thursday, September 27, 2007  10:24 AM 

15
image reversed left to right
turn off rear in Settings>System menu
correct image 
projected colors don’t match source
adjust color, tint, color temperature, brightness, contrast in the menus. Verify 
cable connections.
correct image
lamp won’t turn on, Temperature light is on
make sure vents aren’t blocked, turn off the projector and allow it to cool for one 
minute 
lamp turns on
A
AB
COLOR
COLOR
Temperature light
K1 RG.fm  Page 15  Thursday, September 27, 2007  10:24 AM 

16
Still need assistance?If you need assistance, visit our website at www.infocus.com or call us. This prod
-
uct is backed by a limited warranty. An extended warranty plan may be purchased 
from your retailer or dealer. When sending the projector in for repair, we recommend shipping the unit
 
in its original packing material, or having a professional packaging company pack the 
unit. Please insure your shipment for its full value.“Change lamp” message appears at startup or
 
Lamp light is turned on...

17
Using the remote controlThe remote uses two (2) AA batteries. They are easily installed by sliding the cover 
off the remote’s back, aligning the + and - ends of the batteries, sliding them into 
place, and then replacing the cover.To operate, point the remote at the projection screen or at the front of the pro
-
jector (not at the video device or computer). The range of optimum operation is 
up to 30 feet (9.14m).Press the remote’s Menu button to open the projector’s menu system. Use the 
arrow...

18
Optimizing video imagesYour projector has been factory optimized for excellent performance no matter 
what the source. However, if you wish to make further changes you can optimize 
the image using onscreen menus. For general information on using the menus, see page
 19.
 Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture menu 
(
page
 20). 
 Select a Sharpness setting (
page
 22).
 Use the Color Control to adjust the color gain and offset (
page
 23).
 Adjust the Color...

19
Using the menusTo open the menus, press the Menu button on the remote. (The menus automat
-
ically close after 60 seconds if no buttons are pressed.) The Main menu appears. 
Use the arrow buttons to move up and down to highlight the desired submenu, 
then press the Select button. To change a menu setting, highlight it, press Select, then use the up and down 
arrow buttons to adjust the value, select an option using radio buttons, or turn the 
feature on or off using check boxes. Press Select to...