InFocus Projector Play Big In74ex User Manual

							30
4
Push the 2 tabs on the lamp door toward the front of the projector and 
lift the lamp door off.
5
Loosen the three captive screws that attach the lamp housing to the pro
-
jector.
6
Detach the lamp connector from the projector by depressing the locking 
tab on the connector and lightly pulling it free.WA R N I N G:To avoid burns, allow the projector to cool for at least 60 minutes 
before you replace the lamp.Be extremely careful when removing the lamp housing. In the 
unlikely event that the bulb ruptures, small glass fragments may be 
generated. The lamp housing is designed to contain these frag
-
ments, but use caution when removing the lamp housing. Before 
replacing the lamp, clean the lamp compartment and dispose of 
cleaning materials. Wash hands after lamp replacement. This prod
-
uct has a lamp which contains a very small amount of mercury. Dis
-
pose of it as required by local, state or federal ordinances and 
regulations. For more information see www.eiae.org.
7
Carefully remove the lamp housing. Dispose of the lamp in an environ
-
mentally proper manner. 
8
Install the new lamp housing and tighten the screws.
9
Re-attach the lamp connector to the projector. The locking tab should 
engage when the connector is fully plugged in.
lamp door
lamp 
housing
lamp
connector captive screws 
						

							31
10
Replace the lamp door.
11
Replace the base or ceiling mount plate, if necessary.
12
Plug in the power cord and press the Pow e r button on the remote or 
keypad to turn the projector back on.
13
To reset the lamp hour timer, navigate to the Settings>Service menu 
and select Reset Lamp Hours
. See 
page
 28 for details.
Service menu 
						

							32
AppendixRed LED behavior and projector errorsIf the projector is not functioning properly and the LED is blinking red, con
-
sult Ta b l e  4 to determine a possible cause. There are two-second pauses 
between the blinking cycles. Visit our website for more details on the red 
LED error codes.
Table 4: LED Behavior
Red LED Behavior
Explanation
One (1) blink
The lamp wont strike after five (5) 
attempts. Check the lamp and lamp door 
installations for loose connections.
Two (2) blinks
The lamp counter hours have exceeded 
lamp life hours. Replace the lamp and 
reset the lamp hours counter.
Three (3) blinks
The projector has shut down. Check to 
see if the lamp door is open. If the lamp 
door is closed, toggle off the projector 
and wait one minute, then toggle the pro
-
jector on again. If the lamp does not strike 
after one minute, replace the lamp. Con
-
tact Technical Support for repair if replac
-
ing the lamp does not solve the problem.
Four (4) blinks
The fan has failed. Contact Technical Sup
-
port for repair or replacing the fan.
Five (5) blinks
The projector is overheating. Check for a 
blocked air vent (
page
 16). Contact Tech
-
nical Support for repair if clearing the 
vents/screens does not solve the problem. 
						

							33
Remote control discrete codesYou can use these codes to program another remote to learn the projector ’s 
remote functions.To activate discrete mode, press and hold the Custom button on the remote 
for 10 seconds. The back light blinks twice when discrete mode is entered. 
The remote buttons are now remapped to new functions as listed below. To 
return to normal remote mode, press and hold the Custom button on the 
remote for 10 seconds. The remote also returns to normal mode automati
-
cally if no activity is detected for 2 minutes.
Table 5: Remote control discrete codes
Function
Description
Remote 
button
Power off
turns power off
Nav Up
Power on
turns power on
Nav Down
Native resize
selects Native resize
resize
16:9 resize
selects 16:9 resize
overscan
4:3 resize
selects 4:3 resize
source
Letterbox 
resize
selects letterbox resize
custom
Natural wide 
resize
selects natural wide resize
auto image
User preset 1
selects user preset 1
Source 1
User preset 2
selects user preset 2
Source 2
User preset 3
selects user preset 3
Source 3 
						

							34
Projector dimensions for ceiling mount installationsAll values in millimeters (mm). 
234.5126.5 361
121
40.2557
64
344.2
5
167
40.5
24.5
163
227.5
245.5 
						

							35
Supported video formats
Connector
Signal Type
Supported formats
HDMI
Digital RGB and YCrCb
480i/50Hz/60Hz480p/50Hz/60Hz576i/50Hz/60Hz576p/50Hz/60Hz720p/50Hz/60Hz1080i/50Hz/60Hz1080i/50Hz (Australia)
Digital RGB video via M1-to-DVI cableAnalog RGB video via M1-to-VESA cable
M1-DA
YPrPb video via M1-to-Component adapterAnalog Computer via M1-to-VESA cable
All industry-standard analog and digi
-
tal computer formats conforming to 
VESA standards
Digital Computer via M1-to-DVI cable
Component
YPrPb
480i/p/50Hz/60Hz576i/p/50Hz/60Hz720p/50Hz/60Hz1080i/50Hz/60Hz1080i/50Hz (Australia)1080p/241080p/60 (sub-sampled)
Composite
Composite Video
NTSC: M, 4.43PAL: B,G,H,I,M,NSECAM: M
S-video
S-VHS Y/C
RGBS
RGB-C or RGB-S via SCART-to-4 wire RGB 
adapter cable
SCART-RGB (576i/p) 
						

							36
RS-232 terminal specifications for IN74 and IN76Communication configurationTo control the projector from an LCD control panel, connect an RS-232 cable 
to the serial control connector on the projector and set your computer ’s 
serial port settings to match this communication configuration:Command formatAll commands consist of 3 alpha characters followed by a request, all 
enclosed in parentheses. The request can be a read request (indicated by a 
“?”) or a write request (indicated by 1 to 4 ASCII digits).A read request format: (AAA?) where
( starts the commandAAA denotes the command? denotes the read request) ends the command
A read command returns the range and the current setting, for example
:
A write request example: (AAA####) where
( starts the commandAAA denotes the command#### denotes the value to be written
 
(leading zeros not necessary)
) ends the command
Some commands have ranges, while others are absolute. If a number 
greater than the maximum range is received, it is automatically set to the 
maximum number for that function. If a command is received that is not 
understood, a “?” is returned. With absolute settings, “0” is off, 1-9999 is on. 
The one exception is the Power command, where 0 is off and 1 is on
.
Setting
Va l u e
Bits per second
19,200
Data bits
8
Parity
None
Stop bits
1
Flow control
None
Emulation 
VT100
Function
Command
Response
Brightness 
(BRT?)
 (0-22, 10)
Lamp hours
(LMP?)
(0-9999, 421)
Function
Command
Response
Brightness 
(BRT10)
Sets the brightness to 10
Power
(PWR0)
Turns power off
Power
(PWR1)
Turns power on
Power
(PWR9999)
? 
						

							37
Supported commandsFunction
Command
Range
Default
Auto Ceiling Enable
ACL
0-1
0
Auto Color Space enable
ACS
0-1
1
Auto Image
AIM
0-1
0
Aspect Ratio
ARZ
0-40 = Native1 = 4:3 2 = 16:93 = Letterbox4 = Natural Wide
1
Auto Power Enable
APO
0-1
0
Auto Source Enable
ASC
0-1
1
Auto Video Standard Enable
AV S
0-1
1
Blank
BLK
0-1
0
Blank Screen Enable
BLK
0-10 = black1 = blue
0
Blue Color Offset
BCO
1-255
128
Blue Gain
BCG
1-255
128
Blue Only Enable
BOE
0-1
0
Brightness
BRT
0-255
128
Ceiling
CEL
0-1
0
Color
CLR
0-100
50
Color Space
CSM
0-20 = RGB3 = REC7092 = REC601
0
Color Temp
TMP
0-30 = 6500 1 = 75002 = 93003 = Native
0
Contrast
CON
0-255
128
Display Messages
DMG
0-1
1
Factory Reset (Write only)
RST
0-1
n/a
Flesh Tone Correction
FTC
0-1
0
Gamma Table
GTB
0-82 = Video3 = Film5 = Bright Room 7 = CRT8 = PC
3
Green Color Offset
GCO
0-255
128
Green Gain
GCG
0-255
128
High Power Enable
HPE
0-1
0
Horizontal Position 
HPS
n/a
n/a
Ve r t i c a l  Ke y s t o n e
DKC
0-80
40
Lamp Hours (Read only)
LMP
0-65535
0
Number of Lamp Resets
LMR
0-65535
0
Menu Enable
MNU
0-1
0
Menu Navigation
NAV
0-31 = up2 = down3 = select
n/a 
						

							38
Language
LAN
0-11
 
0 = English1 = French2 = German3 = Italian4 = Japanese5 = Korean6 = Norwegian7 = Portuguese8 = Russian9 = Chinese Simpli
-
fied10 = Spanish11 = Chinese Tra
-
ditional
0
Noise Reduction Mode
NRE
0-10 = Off1 = Auto
0
Noise Reduction Level
NRL
8-248
128
Overscan
OVS
0-2
0
Phase
MSS
0-100
50
Power Enable
PWR
0-1
0
Power Save Enable
PSV
0-1
0
Presets
PST
0-50 = default1 = User 12 = User 24 = Off
0
Rear Project
REA
0-1
0
Red Color Offset
RCO
0-255
128
Red Gain
RCG
0-255
128
Sharpness
SHP
0-4
2
Sleep Timer
SLT
0-1
0
Sync Threshold Adjust
STH
1-15
8
Source
SRC
0-5
 
0 = HDMI1 = M1-DA2 = Component3 = S-Video4 = Composite5 = SCART RGB
2
Source 1 Program
SR1
0-5
0
Source 2 Program 
SR2
0-5
2
Source 3 Program 
SR3
0-5
3
Source 5 Program 
SR4
0-5
3
Startup Logo
DSU
0-2
2
Tint
TNT
2-98
50
Film Mode Auto Detect
TTO
0-1
1
Tracking 
MTS
0-100
50
Total number of successful 
Strike Attempts
SSA
0-65535
0
Screen Trigger Enable
STE
0-1
1
System State
SYS
0-17
0
Translucent OSD
TO E
0-1
1
Test Pattern Enable
TPO
0-1
0
Test Pattern Select
TPS
0-9
0
Total number of Strike 
Attempts
TSA
0-65535
0
Ve r t i c a l  P o s i t i o n  
VPS
0-100
50 
						

							39
Video Standard
VSU
0-9
 
0 = Auto1 = NTSC2 = PAL5 = SECAM
0
White Peaking
WPK
0-10
1
Save User1 Preset
US1
0-1
0
Save User 2 Preset
US2
0-1
0
Save User 3 Preset
US3
0-1
0
Logo Capture Enable
CAP
0-1
0
Source Enable 0
CE0
0-1
0
Source Enable 1
CE1
0-1
0
Source Enable 2
CE2
0-1
0
Source Enable 3
CE3
0-1
0
Source Enable 4
CE4
0-1
0
Source Enable 5
CE5
0-1
0
Logo Capture Compress
COM
0-1
0
Logo Capture Compression 
Progress Count
CPC
0-480
0
Current Subsource
CRS
0-7
0
Power-up Source
DSC
0-5
2
Effect Key Program
EFK
0-11
8
System Error Code
ERR
0-7
0
Freeze Enabled
FRZ
0-1
0
Lamp Power
IPM
0-1
0
Time in Hours Last Bulb1 
Lasted
LB1
0-65535
0
Time in Hours Last Bulb2 
Lasted
LB2
0-65535
0
Time in Hours Last Bulb3 
Lasted
LB3
0-65535
0
Illuminating State
LML
0-2
0
Lamp Total Time On in 
hours for all bulbs
LMT
0-65535
0
Perform Lamp Reset
LRT
0-1
0
Number of times unit has 
been turned on
O00
0-65535
0
Number of times unit has 
been turned on for at least 
30 minutes
O30
0-65535
0
Number of times unit has 
been turned on for at least 
60 minutes
O60
0-65535
0
Number of times unit has 
been turned on for at least 
90 minutes
O90
0-65535
0
Time in minutes unit has 
been turned on
ONC
0-4294967295
0
Time in minutes unit is cur
-
rently on
ONL
0-4294967295
0
Time in minutes unit was 
previously turned on
ONP
0-4294967295
0