InFocus Projector Play Big In74ex User Manual

							
Trident
IN72/IN74/IN76Reference Guide 
						

							1
Declaration of ConformityManufacturer: InFocus Corporation, 27700B SW Parkway Ave. Wilsonville, Oregon 
97070 USA
 
European Office: Strawinskylaan 585, 1077 XX Amsterdam, The Netherlands
 
We declare under our sole responsibility that this projector conform to the following 
directives and norms:
EMC Directive 89/336/EEC, Amended by 93/68/EEC
 
EMC: EN 55022
 
           EN 55024
 
 EN 61000-3-2
 
 EN 61000-3-3
 
Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC
 
Safety: IEC 60950-1: 1
st Edition
 
December, 2005TrademarksAdobe and Acrobat are trademarks or registered trademarks of Adobe Systems 
Incorporated. Digital Light Processing is a trademark or registered trademark of 
Texas Instruments. Pixelworks is a trademark or registered trademark of Pixelworks 
Inc. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks 
or registered trademarks of HDMI Licensing LLC.
 InFocus, In Focus, and INFOCUS 
(stylized), LP, LiteShow, LitePort, ASK and Proxima are either registered trademarks 
or trademarks of InFocus Corporation in the United States and other countries. 
FCC WarningNote: This equipment has been tested and found to comply with the limits for a Class 
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses and can radiate radio frequency energy 
and, if not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be determined by 
turning the equipment off and on, the user is encouraged to try to correct the 
interference by one or more of the following measures:
 
--Reorient or relocate the receiving antenna.
 
--Increase the separation between the equipment and receiver.
 
--Connect the equipment into an outlet on a circuit different from that to which the 
receiver is connected.
 
--Consult the dealer or an experienced radio/TV technician for help.CanadaThis Class B digital apparatus complies with Canadian ICES-003.
 
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.Agency ApprovalsUL, cUL, TUV, GOST Other specific Country Approvals may apply. Please see product certification label. This document applies to models IN72, P720, IN74, P740, IN76, and P760.InFocus reserves the right to alter product offerings and specifications at any time 
without notice. 
						

							2
Table of Contents
Introduction 3
Positioning the projector  5
Choosing the aspect ratio 6
Video connectors  7
Connecting a video device  8
Composite (RCA) video connection  8
S-video connection  8
Component (RCA) connection  8
SCART RGB connection  8
Digital connections  9
DVI connection  9
HDMI connection  9
Computer connections  9
RS-232 connections (IN74 and IN76 only)  9
Displaying an image  10
Adjusting the image  10
Shutting down the projector  12
Troubleshooting your setup  12
Using the remote control  18
Using the keypad buttons  19
Optimizing video images  20
Customizing the projector  20
Using the menus  21
Picture menu  22
Settings menu  26
Maintenance 29
Cleaning the lens  29
Replacing the projection lamp  29
Appendix 32
Red LED behavior and projector errors  32
Remote control discrete codes  33
Projector dimensions for ceiling mount installations  34
Supported video formats  35
RS-232 terminal specifications for IN74 and IN76  36
Important Operating Considerations for Safety Place the projector in a horizontal position no greater than 15 degrees 
off axis. Locate the projector in a well-ventilated area without any obstructions 
to intake or exhaust vents. Do not place the projector on a tablecloth or 
other soft covering that may block the vents.  Locate the projector at least 4 (1.2 m) away from any heating or cooling 
vents. Use only InFocus-approved ceiling mounts. Use only the power cord provided. A surge-protected power strip is 
recommended. Refer to this guide for proper startup and shutdown procedures. This product has a lamp which contains a very small amount of mer
-
cury. Wash hands after cleaning the area and handling the ruptured 
lamp. Dispose of it as required by local, state or federal ordinances and 
regulations. For more information see www.eiae.org.
 In the unlikely event of a lamp rupture, particles may exit through the 
projector side vents. When the projector is turned on, keep people, 
food, and drinks out of the keep out area under and around the pro
-
jector, as indicated by the X areas below.
Follow these instructions to help ensure image quality and lamp life over 
the life of the projector. Failure to follow these instructions may affect the 
warranty. For complete details of the warranty, see the Warranty booklet.
5’/1.5m
8’/2.4m
2’/0.6m
3’/1m
3’/1m 
						

							3
IntroductionYo u r  n e w  I n F o c u s
 projector is specifically designed for home theater appli
-
cations. It sets a high standard using the latest DLP™ technology and new 
DNX video processing from Pixelworks™. Whether you are watching mov
-
ies or High Definition broadcasts or playing the latest video game, you will 
enjoy amazing image quality. The unique design and color of the projector 
make it a welcome addition to your home.The projector is available in 3 different resolutions: IN72 has 854x480 resolution (480p) IN74 has 1024x576 resolution (576p) IN76 has 1280x720 resolution (720p)This advanced reference guide covers all 3 models. Differences between the 
models are noted. Product specificationsTo read the latest specifications, be sure to visit our website at www.info
-
cus.com as specifications are subject to change. AccessoriesThe standard accessories that came with your projector are listed on the 
included user ’s guide. Optional accessories can be found on our website at 
www.infocus.com or at your retailer or dealer.Online RegistrationRegister your projector on our website at www.infocus.com/register to acti
-
vate your warranty and receive product updates, announcements, and reg
-
istration incentives. 
 
focus 
remote control 
receiver (IR)zoom (outer ring)
panelbase
connectorkeypad 
						

							4
Connector PanelThe projector provides the following connection options:  M1-DA/DVI (Digital Visual Interface)  HDMI™ (High Definition Multimedia Interface) Component (RCA) SCART RGB (you must enable this connector, see 
page
 26)
S-video Composite video (RCA)See 
“Video connectors” on page
 7 for details.
 
The projector also provides the following connectors: RS-232 for serial control (not included on the IN72) 12 volt DC output (see below)   12 volt DC outputThe 3.5mm mini-jack trigger provides a 12 volt, 0.25 amp DC output. It pro
-
vides a constant output while the projector is on. It has numerous uses. For 
example, if you connect your projection screen to the 12 volt DC output 
with the cable that came with your screen, when you turn on the projector 
the screen will move down; when you turn the projector off, the screen will 
return to the storage position. 
M1-DA/S-video
12 volt 
DC output
component RCA
 composite
HDMI
RS-232
(not on IN72)
DVI
RCA
12 volt DC output +12v
ground
3.5mm plug
to, for example, screen relay (see screen manufacturer
for details) 
						

							5
Positioning the projectorTo determine where to position the projector, consider the size and shape of 
your screen, the location of your power outlets, and the distance between 
the projector and the rest of your equipment. Here are some guidelines: Position the projector on a flat surface at a right angle to the screen. The 
projector must be at least 4.9 feet (1.5m) from the projection screen. For safety reasons, position the projector within 10 feet (3m) of your 
power source (running extension cables may introduce a trip hazard). 
To ensure adequate cable access, do not place the projector within 6 
inches (.15m) of a wall or other object. If you are installing the projector on the ceiling, refer to the installation 
guide that comes with the Ceiling Mount Kit for more information. To 
turn the image upside down, see “Ceiling” on 
page
 26. We recommend 
using an InFocus authorized ceiling mount.
 Position the projector the desired distance from the screen. The distance 
from the lens of the projector to the screen, the zoom setting, and the 
video format determine the size of the projected image.  The image offset is 128% for the IN72. This means that if you have an 
image 10’ high, the bottom of the image will be 2.8’ above the center of 
the lens. For the IN74 and IN76, the image offset is 115%.
NOTE: Visit the Service section of our website at www.infocus.com/calcu
-
lator for an interactive image size calculator.
bottom of image
2.8 ft above center10 ft high
imageProjection angle in 16:9 mode
lens center of lens
Table 1: 
Range of distance to the screen for a given screen size 
for the IN72
Diagonal 
Screen Size 
(inches/m) 
Distance to screenMaximum 
distance
 
(feet/m)
Minimum 
Distance
 
(feet/m)
60/1.5
9.3/2.8
7.8/2.4
80/2
12.3/3.8
10.4/3.2
92/2.3
14.2/4.3
12/3.7
150/3.8
23.1/7
19.5/5.9
Table 2: 
Distance to the screen for a given screen size for the 
IN74/IN76
Diagonal 
Screen Size 
(inches/m) 
Distance to screenMaximum 
distance
 
(feet/m)
Minimum 
Distance
 
(feet/m)
60/1.5
8.3/2.5
6.6/2
80/2
11.1/3.4
8.8/2.7
92/2.3
12.8/3.9
10.1/3.1
150/3.8
20.8/6.3
16.4/5 
						

							6
Choosing the aspect ratioAspect ratio is the ratio of the image width to image height. HDTV and 
most DVDs are 16:9, which is the default for this projector. When in 4:3 
mode the projector places black bars on both sides of the image. Native 
mode centers the image and turns off the internal scaler so that any resolu
-
tion larger than the native projector resolution is cropped on the edges. Let
-
terbox expands the image to fill the screen.What you plan to project will also help you choose between 4:3 and 16:9. For 
example, most TV shows are 4:3, while most movies are 16:9. If you have a 
16:9 screen, then you should select an aspect ratio of 16:9 for anamorphic 
movies and HDTV, and Native for 4:3 content. If you have a 4:3 screen you 
should still use 16:9 for anamorphic movies or HDTV, but you also have the 
option of using 4:3, Native, or Natural Wide for 4:3 content. Keep in mind 
that anamorphic movies only appear correctly if the DVD player is set to 
output to a 16:9 television. Natural Wide stretches a 4:3 image to fill the 
entire 16:9 screen. The center two-thirds of the image is unchanged; the 
edges of the image are stretched.
16
16 99 16:9 image input16:9 image 
16:9
aspect ratio16 9
4 34:3 image input 4:3 image on 16:9 screen
black bars
black bars
4:3 aspect ratio
16 9 letterbox image input
16:9 image fills 16:9 screen
black bars
black bars
4 3 letterbox
aspect ratio
4:3 image fills 16:9 screen
natural wide
aspect ratio4:3 image input
4 3
16 9 
						

							7
Video connectorsThe first step for connecting video is determining what type of output con
-
nectors your video device has. If there is more than one output, select the 
one with the highest quality. The best quality ranking, with 1 being the 
highest, is:1
M1-DA/DVI or HDMI (both are digital inputs)
2
component /SCART RGB video (RCAs)
3
S-video 
4
composite video (RCA)
If your device has a VGA connector, you can use the M1-DA/DVI connector 
for a high quality image. Many PC game systems have VGA connectors. 
M1-DA/S-video
12 volt 
DC output
component RCA
 composite
HDMI
RS-232
(not on IN72)
DVI
RCA
SCART (all 4 connectors) 
						

							8
Connecting a video deviceYou can connect video devices such as VCRs, DVD players, camcorders, 
digital cameras, video game consoles, HDTV receivers, and TV tuners to the 
projector. Connect the audio from your video device to your stereo system 
to get sound.You can connect the projector to most video devices that can output video. 
You cannot directly connect the coaxial cable that enters your house from a 
cable or satellite company, the signal must pass through a tuner first. Exam
-
ples of tuners are digital cable boxes, VCRs, digital video recorders, and sat
-
ellite TV boxes. Basically, any device that can change channels is considered 
a tuner.A composite video cable is provided with your projector so you can quickly 
and easily connect a video source to the projector and see the amazing 
image that is displayed. Once you have determined a more permanent loca
-
tion for your projector, we recommend purchasing higher quality cables in 
the proper length to get the best image from your particular video equip
-
ment. High quality cables optimized for your projector can be purchased 
from www.infocus.com/store (in select areas) or from your dealer or 
retailer.Composite (RCA) video connectionPlug the composite video cable’s yellow connector into the video-out con
-
nector on the video device. Plug the other yellow connector into the yellow 
Composite connector on the projector. S-video connectionIf your video device uses a round, four-prong S-video connector, plug the 
 
S-video cable into the S-video connector on your video device and into the 
S-video connector on the projector. 
Component (RCA) connectionIf your device uses component connectors, plug a component video cable 
with red, green, and blue RCA connectors into the source device’s compo
-
nent connectors and the Component connectors on the projector.SCART RGB connectionSCART (from Syndicat des Constructeurs dAppareils Radiorécepteurs et 
Téléviseurs) is a French-originated standard and connector for connecting 
audio and video equipment to display devices. The video signal is sepa
-
rated into its primary components for brighter, more accurate colors and 
sharper detail. You must enable this connector in the Source Enable menu to 
use it, see 
page
 26. You will also need a SCART to 4-RCA adapter to connect 
to your SCART device. 
						

							9
Digital connectionsThe M1-DA/DVI and HDMI (High-Definition Multimedia Interface) con
-
nectors are digital and yield the highest quality image. It is common for 
these signals to be encrypted with HDCP (high-bandwidth digital-content 
protection). Your new projector ships standard with decryption codes so 
you can enjoy these high quality, all digital images. This projector uses the M1-DA connector, which has the following advan
-
tages: allows connection to a digital DVI source allows connection to a component source allows connection to an analog computer source carries a USB control signal which allows you to easily update your 
projector ’s software as enhancements become available. has output pins that can power accessories.The IN76 is an HDTV (High Definition Television) monitor, meaning it has 
vertical scanning lines of 720 progressive, 1080 interlaced or higher. The 
IN72 and IN74 are EDTV (Enhanced Definition Television) monitors, mean
-
ing they have vertical scanning lines of 480 progressive or higher. HD con
-
tent can be displayed on an EDTV monitor, the resolution is just less than 
that of an HDTV.DVI connectionIf your video device uses a DVI connector, plug the DVI end of an M1-DA 
cable into the video-out connector on the video device. This connector may 
be labeled “To Monitor” on the video device. Plug the M1-DA end of the 
cable into the M1-DA/DVI connector on the projector. 
HDMI connectionHDMI is a standard, uncompressed, all-digital audio/video interface. 
HDMI provides an interface between sources, such as set-top boxes, DVD 
players, and receivers and your projector. Plug an HDMI cable into the 
video-out connector on the video device and into the HDMI connector on 
the projector.Note that the projector has no audio capabilities, so audio signals trans
-
ferred through HDMI will not be audible.Computer connectionsYou can connect a computer ’s VGA connector to the M1-DA/DVI input on 
the projector using an M1-A cable.RS-232 connections (IN74 and IN76 only)You can control the projector from an LCD control panel or computer by 
connecting an RS-232 cable to the projector ’s Serial control connector. Spe
-
cific RS-232 commands can be found in the Service section of our website at 
www.infocus.com/support.