InFocus Projector Lp580b User Manual

							LitePro 580 User’s Guidei
Contents
Safety summaryiii
Introduction1
Unpacking the projector 2
Compatibility 4
Cables and adapters 5
Usage guidelines 5
If you need assistance 6
Setting up the LitePro 5807
Getting started 7
Positioning the projector 8
Connections to the projector 8
Connecting a computer 9
Connecting video equipment 14
Connecting the remote control by cable 17
Powering up and adjusting the LitePro 580 18
Turning off the LitePro 20
Using the LitePro 58021
Basic functions 21
Display mode controls 23
Menu mode controls 24
Using the menus 25
Reference to menu functions 26
Using LP Utilities33
Connecting your computer 33
Installing the LP Utilities software 34
LP-Link Utility 35
LP Remote Programmer Utility 43 
						

							iiLitePro 580 User’s Guide
Maintenance47
Cleaning the lens 47
Cleaning the remote control 48
Cleaning the fan intake filter 49
Replacing the projection lamp 50
Replacing batteries in the remote control 52
Replacing the fuse 53
Troubleshooting55
Before you call for assistance 55
Common problems and solutions 56
Monitor lights 59
Appendix61
Compatibility and cabling 61
About broadcast video 61
About computer video 62
Specifications 63
Pin assignments 64
Order information 66
Laptop display activation chart 67
Index71 
						

							LitePro 580 User’s Guideiii
Safety summary
Please read these instructions before using your LitePro. Failure to 
comply with these instructions could result in fire, electrical shock, 
personal injury or damage to equipment.
These graphics are used throughout this manual to draw your 
attention to important information about the LitePro:
Additional useful details or tips
Steps to avoid damage to your equipment
Steps to avoid personal injury
Do not look into the lens!
Be very careful not to look into the projection lens when the projector 
is turned on. The bright light may harm your eyes. Be especially 
careful to keep children from looking into the lens.
Power source
Use only a three-wire grounding type power source. The power 
source should not exceed 250 volts rms between the supply 
conductors or between either conductor and the ground.
Power cord
Use only the power cord that was shipped with the LitePro. Although 
other power cords might be similar in appearance, they have not 
been safety-tested with the LitePro. Do not use a power cord if it has 
become damaged or frayed. Contact your In Focus dealer or call In 
Focus if you need to replace your LitePro power cord. 
						

							Safety summary
ivLitePro 580 User’s Guide
Grounding
The LitePro is grounded through the grounding conductor on the 
power cord. To avoid electric shock, plug the power cord into a 
properly wired receptacle. Do not defeat the purpose of the 
grounding-type plug.
Fuse
For protection against the risk of fire, use only a fuse of the specified 
type. Refer to page 63 for more information about fuse specifications 
and to page 53 for instructions on replacing the fuse.
Lamp
To avoid overheating and unacceptable image quality, replace the 
projection lamp with a lamp of the specified type. Refer to page 63 for 
lamp specifications and to page 50 for instructions on replacing the 
lamp.
Hot surfaces
Allow the LitePro to cool at least 20 minutes before replacing a lamp. 
When you open the lamp housing, be very careful not to touch the 
hot surfaces inside.
Ventilation and overheating
Openings in the LitePro case provide ventilation to protect it from 
overheating. Keep loose papers and other objects well away from the 
bottom, top and side grills. Do not place the LitePro on top of or close 
to a computer or other heat-producing equipment.
Liquid spills
Do not set drinks on top of the LitePro. Spilled liquids can flow inside 
and damage the LitePro.
Do not disassemble
All service must be performed by an authorized In Focus service 
center. The only user-serviceable part in the LitePro is the projection 
lamp, which you can replace by opening the lamp cover on the 
bottom of the projector. Do not open any other part of the LitePro.  
						

							LitePro 580 User’s Guide1
Introduction
The In Focus Systems LitePro 580 is a multimedia projector designed 
for portability, durability, and ease of use. It displays the brightest 
and clearest images generated by your computer and video equip-
ment. 
The LitePro 580 connects to most IBM-compatible and Macintosh 
computers. It also connects to VCRs, laser disc players, and camcord-
ers using any of the worldwide video standards, including NTSC, 
PAL, and SECAM. Both computer and video sources have separate 
audio channels for better sound quality direct from the projector or 
from external speakers. The versatility of the LitePro 580 allows you 
to enhance your presentations by switching back and forth between 
computer-generated graphics and full-motion video with sound. 
						

							Introduction
2LitePro 580 User’s Guide
Unpacking the projector
The projector comes with the parts shown below. Check to make sure 
all are included. If any parts are missing, contact your dealer immedi-
ately.
If you are experienced in setting up presentation systems, use the 
Quick Start card at the front of this manual. For complete details on 
connecting and operating the projector, refer to the appropriate chap-
ters in this manual.
. 
s
It is recommended that you do not reuse the LitePro’s 
shipping carton to transport or ship the LitePro.
1. LitePro 580 LCD projector 8. Remote control
2. Lens cover 9. Batteries for the remote control
3. Power cord 10. LitePro Utilities kit
4. Fuse (6.3A. 250V. T.) a. LitePro Utilities serial cable
5. VGA (Y-shaped) cable b. Mac adapter for serial cable
6. Mac adapters for VGA cable c. LitePro Utilities disks
7. Audio/video cable 11.  LitePro 580 User’s Guide
1
78
2
43
5
69
119
10c10a
10b
c
Shipping Box Contents 
						

							Introduction
LitePro 580 User’s Guide3
 temperature monitorprojector control panel speakers
elevator foot
 remote control receiverpower switch handle
lamp monitor
operation monitor remote control
lens zoom ring
lens focus ring
elevator foot button connector ports
fan exhaust grillpower cord 
connector
receiver 
fuse holder
fan intake grill
LitePro 580—Front and rear view 
						

							Introduction
4LitePro 580 User’s Guide
Compatibility
The LitePro 580 is compatible with a wide variety of computers and 
video devices, including:
• IBM-compatible desktop and laptop systems 
• Macintosh systems (including LC, Performa, Quadra, 
PowerBook, and Power Mac units)
• Various VCRs, camcorders, laser disc and CD players
elevator feetfan intake grill
lamp cover
LitePro 580—Bottom view 
						

							Introduction
LitePro 580 User’s Guide5
Cables and adapters
The LitePro 580 comes with these cables and adapters:
• VGA cable, a Y-shaped cable that connects the LitePro to your 
computer and its monitor. Its ends are labeled “LCD,” “Monitor,” 
and “VGA.”
• Two Macintosh adapters for the VGA cable.
• Audio/video cable to connect the LitePro to your video 
equipment.
• LP Utilities serial cable to connect the LitePro to your computer.
• Macintosh adapter for the LP Utilities serial cable.
• Power cord.
Usage guidelines
• The LitePro can become very warm during use. Make sure there 
is no flammable material such as paper or cloth under, on, or near 
the projector. Use extreme care when handling the projector. We 
recommend that you let the projector cool before lifting it.
• Do not block the ventilating grill on the left side of the projector. 
Restricting the air flow can cause it to overheat and shut down 
automatically.
• Do not place objects on or insert metallic objects in the projector. 
• Avoid leaving the LitePro in direct sunlight or extreme cold for 
extended periods of time. If this happens, allow it to reach room 
temperature before use.
• Do not expose the LitePro to moisture or dust. 
• Handle the LitePro as you would any product with glass 
components. Do not drop it.
• Transport the LitePro in the original shipping carton or vendor-
approved hard or soft case. 
						

							Introduction
6LitePro 580 User’s Guide
If you need assistance
The first place to look for help is in this manual. Check the 
chapter on “Troubleshooting” beginning on page 55.
If this manual does not answer your question, call your In Focus 
dealer. You can also call In Focus Technical Support directly at 
1-800-294-6400. Call between 6 a.m. and 5 p.m. PST, Monday 
through Friday. In Europe, call In Focus in The Netherlands at 
31 (0) 2503-23200.
Your LitePro is backed by a limited one-year warranty. For 
details, see the last page of this manual.