InFocus Projector Lp260 User Manual

							23
Gamma
Press the point left or right button to obtain better contrast from 0 
to 16.
Auto Image menu
Auto image automatically adjusts fine sync, total dots, and image 
position for most computers. You can turn these automatic 
adjustments off and set these parameters manually, if desired.
1Select Auto Image in the menu.
The “Auto Adjust Image” menu appears.
2Move the arrow to the desired parameter using the up and 
down 
point buttons.
3Press 
select to turn the automatic adjustments on and off. 
Fine sync and Horiz. Size
See page 22 for instructions on setting these manually.
Po s i t i o n
See the following section for instructions on setting this manually.
Press Save to store the on/off settings, press Start to start Auto 
Image adjustments, and press Quit to exit this menu.
auto image menu 
						

							24
Using the Projector
Po s i t i o n  m e n u
You can move the image up, down, left and right using this 
menu.
1Select the Position menu.
The “Position” menu appears.
2Use the 
point buttons to adjust the position.
Press the 
select button to chose a position. To cancel this adjust-
ment, press any button except the 
point buttons. 
position menu 
						

							25
Screen menu
1Select the Screen menu.
The “Screen Adjustments” menu appears.
.
2Move the cursor to the desired feature.
Tr u e
NOTE: True and Digital Zoom 
are not available when RGB, 
HDTV1035i, or HDTV1080i is 
selected in the System menu.
Select True to display the image in its original size. If the original 
size is larger than 800x600, the projector enters Digital Zoom 
automatically.
Ke y s t o n e
Select Keystone to adjust the image vertically and make a squarer 
image. The menus disappear and the message “Keystone” 
appears. Adjust the keystone using the 
keystone up/down buttons 
on the remote or the 
point up/down buttons on the keypad. See 
page 12 for details.
Digital Zoom
NOTE: Images not in the projec-
tor’s native resolution of SVGA 
800x600 are automatically modi-
fied to fit the screen in the initial 
mode.
To adjust the image size or pan a computer image, select Digital 
Zoom. The menus disappear and the message “D.Zoom” 
appears. The projector also enters digital zoom mode when the 
d.zoom button on the remote is pressed.
To expand the image size, press the 
d.zoom up button or the select 
button. The image is magnified by degrees.
To compress the image size, press the 
d.zoom down button or the 
right click button. The image is reduced by degrees.
NOTE: Panning may not function 
if the incoming signals have been 
modified in the “PC Adjust” menu.
To pan the image, press the point up/down/left/right buttons. 
Panning only works when the image is larger than the screen 
size.
To exit digital zoom mode, press any button except 
d.zoom, 
select, right click, or point. To display the image at 800x600, press 
the 
normal button on the remote.
screen menu 
						

							26
Using the Projector
Video Adjustments
Select Video mode by pressing the 
source button on the keypad, 
pressing the 
video button on the remote, or clicking the video icon 
in the menu. 
Video Source menu
The projector automatically detects the signal from any con-
nected video sources. If more than one source is connected, use 
the Video Source menu to select the desire one.
1Press the 
menu button, navigate to the Video Source menu, 
then press the 
select button.
The “Video Source” menu appears.
2Press the 
point down button and position the red arrow by the 
desired source.
NOTE: When both the Video and
S-Video jacks are connected, the
S-video jack input is displayed.
When both the Y-Pb/Cb-Pr/Cr and
S-Video jacks are connected, the
Y-Pb/Cb-Pr/Cr jack input is
displayed.AutoIn this mode, the projector automatically detects the incoming 
video source and adjusts itself to optimize performance.
Video/S-Video/Y, Pb/Cb/Cr
When more than one video source is connected and the projector 
cannot select the proper video source, select the desired source in 
the menu.
source menu 
						

							27
Video System menu
1Press the 
menu button, navigate to the System menu, then 
press the 
select button.
The “Video System” menu appears. 
2Press the 
point down button and position the red arrow by the 
desired source.
When the video signal is from the Video or S-Video jack:
Auto
In this mode, the projector automatically detects the incoming 
video source and adjusts itself to optimize performance. When 
the video system is PAL-M or PAL-N, select the system manually.
PAL/SECAM/NTSC/NTSC4.43/PAL-M/PAL-N
If the projector can’t display the proper video signal, select the 
broadcast signal format from the menu.
system menu 
						

							28
Using the Projector
When the video signal is from the Y, Pb/Cb, Pr/Cr jacks:
Auto
In this mode, the projector automatically detects the incoming 
video source and adjusts itself to optimize performance. 
Component Video Signal Format
If the projector can’t display the proper video signal, select the 
component signal format from the menu. 
						

							29
Screen menu
1Press the 
menu button, navigate to the Screen menu, then 
press the 
select button.
The “Video Screen” menu appears.
2Press the 
point down button and position the red arrow by the 
desired option.
Regular Screen
Normal video image size with 4x3 aspect ratio.
Wide Screen
Resizes the image for wide screen size with 16x9 aspect ratio.
Ke y s t o n e
This option helps to keep the image square as the angle of projec-
tion is changed. When you select Keystone, the menus disappear 
and the message “Keystone” appears. Adjust the keystone using 
the 
key sto ne  up/down buttons on the remote or the point up/down 
buttons on the keypad. See page 12 for details.
screen menu 
						

							30
Using the Projector
Image Menu
1Press the 
menu button, navigate to the Image menu, then 
press the 
select button.
The “Image Adjustments” menu appears.
2Press the 
point down button and position the red arrow by the 
parameter you want to adjust. To change a value, press the 
point left or right button.
Color
The color setting adjusts a video image from black and white to 
fully saturated color. Press the 
point left button to decrease the 
amount of color in the image, press the 
point right button to 
increase the amount of color in the image.
Tint
The tint adjusts the purple-green color balance in the projected 
image. Press the 
point left button to increase the amount of purple 
in the image, press the 
point right button to increase the amount 
of green in the image.
Color Balance (Red/Green/Blue)
Press the point left button to lighten the color, press the point right 
button to deepen the color.
image menu 
						

							31
Contrast
The contrast controls the degree of difference between the lightest 
and darkest parts of the picture. Adjusting the contrast changes 
the amount of black and white in the image. Press the 
point left 
button to decrease the contrast, press the 
point right button to 
increase the contrast, making the blacks appear blacker and the 
whites appear whiter.
Brightness
Adjusting the brightness changes the intensity of the image. Press 
the 
point left button to darken the image, press the point right but-
ton to lighten the image.
Sharpness
This setting adjusts the sharpness of a video image. Press the 
point left button to decrease the sharpness, press the point right 
button to increase the sharpness.
Gamma
Press either the point left or right button to obtain better balance 
of contrast.
Press Save to store the settings, press Reset to restore the previous 
settings, and press Quit to exit this menu. 
						

							32
Using the Projector
Setting menu
1Press the 
menu button, navigate to the Setting menu, then 
press the 
select button.
The “Other Projector Setting” menu appears.
2Press the 
point down button and position the red arrow by the 
parameter you want to adjust. To change a value, press the 
point left or right button. To turn a setting on and off, press the 
select button.
Vo l u m e
NOTE: Changing the volume
using the menu is the same as
changing it using the remote.
Press the point left button to decrease the volume, press the point 
right
 button to increase the volume. 
Mute
Set to “On” to mute the sound. To restore the sound to its previ-
ous level, set “Off” or press the 
mute button or the volume +/- but-
ton on the remote.
Blue Background
When this feature is “On”, the proctor produces a blue image 
when the input source is unplugged or turned off.
setting menu