InFocus Projector Lp260 User Manual

							3
FIGURE 2
Views of the projector
connector panelspeaker
focus ring
zoom ringpower
cord
connector keypad
foot
latch
IR receiver
exhaust ventair intake vent
air intake ventlamp cover
adjustable foot
adjustable foot
air filters 
						

							4
Introduction
Usage Guidelines
 Do not look directly into the projection lens when the lamp is 
turned on. The bright light may harm your eyes.
 Do not block the grills on the projector. Restricting the air flow 
can cause it to overheat and turn off. If this happens, you must 
wait a minute before attempting to turn it back on.
 Handle the projector as you would any product with glass 
components. Be especially careful not to drop it.
 Avoid leaving the projector in direct sunlight or extreme cold 
for extended periods of time. If this happens, allow it to reach 
room temperature before use.
Transport the projector in a vendor-approved hard or soft case. 
Part numbers for these cases are listed on page 45. 
If You Need Assistance
The first place to look for help is in this manual. Be sure to check 
the guidelines in “Troubleshooting” on page 39. Or, check the 
Service and Support section of our website at 
http://www.infocus.com/service. You’ll find a Technical Library, 
FAQs, and support contacts including a technical support e-mail 
form.
If those sources don’t answer your question, call your InFocus 
dealer. You can also call InFocus Customer Service directly at
1-800-799-9911. Call between 6 a.m. and 6 p.m. PST, Monday 
through Friday. Service is available in North America after hours 
and on weekends for a fee at 1-888-592-6800.
In Europe, call InFocus in The Netherlands at 
(31) 35-6474010. 
In Asia, call InFocus in Singapore at 
(65) 332-0659. 
Or, send us an e-mail at 
[email protected]
O u r  Wo r l d  Wi d e  We b  a d d r e s s  i s 
http://www.infocus.com
.
Warranty
This product is backed by a limited two-year warranty. The 
details of the warranty are printed at the back of this manual. A 
longer term warranty can be purchased from your InFocus 
dealer. Refer to page 45 for the part number. 
						

							5
SETTING UP THE PROJECTOR
1Place the projector on a flat surface.
The projector must be within 10 feet (3 m) of your power 
source and within 6 feet (1.8 m) of your computer.
If you want to project from behind a translucent screen, set 
up the projector behind your screen. See “Rear” on page 33 
to reverse the image.
2Position the projector the desired distance from the screen.
The distance from the lens of the projector to the screen and 
the zoom setting determine the size of the projected image. 
Figure 3 and Table 1 show projected image sizes. 
FIGURE 3
Projected image sizes
3Make sure the projector and the computer are turned off.
4.6’ (1.4m)7.8’ (2.4m)13.1’ (4.0m)19.7’ (6.0m)26.3’ (8.0m)
150”200”
167”
H
2
125” 100”
83”
50” 60”
36”
30”H1 Max Zoom
Min Zoom
Ta b l e  1 :  
Image Size, Width and Height
Screen Size
(W x H) mm30” 60” 100” 150” 200”
610 x 457 1219 x 914 2032x1524 3048x2286 4064x3048
Height (H1) 16.6”
(422mm)33.2”
(844mm)55.4”
(1407mm)83.1”
(2110mm)110.8”
(2814mm)
Height (H2) 1.4”
(35mm)2.8”
(70mm)4.6”
(117mm)6.9”
(176mm)9.2”
(234mm) 
						

							6
Setting up the Projector
NOTE: Before you continue,
make sure the projector and all
other equipment is turned off. If
you’re connecting a computer,
make sure the distance between it
and the projector is 6 feet or less.
F
IGURE 4
Connector panel
NOTE: Pressing the reset button
with a pen causes the projector to
shut down and restart. Only press
this button if the projector has
locked up.
NOTE: In the following figures, an
asterisk (*) indicates the cable is
not supplied with the projector.
S-video composite
video
Audio in
videoS-video
computer
PC control audio OUT
computer IN
resetAV
audio
IN
Y ––– Pb ⁄ Cb – Pr ⁄ Cr 
						

							7
Connecting a Computer
The following cables can be used to connect a computer:
NOTE: Many laptop computers 
do not automatically turn on their 
external video port when a sec-
ondary display device such as a 
projector is connected. Refer to 
your computer manual for the 
command that activates the exter-
nal video port. Activation com-
mands for some laptop computers 
are listed in the Appendix of this 
manual on page 46 and in the 
Service section of our website.
VGA HD-15 cable (for all computers)
Mac adapter (for certain Macintosh computers)
PC audio cable (if you want sound with your presentations)
Control cable for serial port/PS-2 port/ADB port (if you want to 
control your computer ’s mouse with the projector ’s remote) 
Audio cable (if you want to connect an external speaker, not 
included*)
FIGURE 5
Connecting the projector to a computer
Now you’re ready to power up the projector and your computer. 
Skip to “Powering up the Projector and Adjusting the Image” on 
page 9.
videoS-video
computer
PC control audio OUT
computer IN
resetAVaudio
IN
Y ––– Pb ⁄ Cb – Pr ⁄ Cr
13 MODE (640 x 480)
16 MODE (832 x 624)
19 MODE (1024 x 768)OFF ON ON
ON ON
ON ONOFF OFF OFF
OFF OFF OFF OFF
OFF OFF OFF OFF1234 56
OFF OFF ON ON ON ON 21 MODE (1152 x 870)
ON
1DIP23456ON
OFF
Desktop computer
Laptop computer
Mac adapter-
set switches
according to 
table below
VGA cableSerial port
PS/2 portADB portAudio output
Use one of these control cables,
depending on your computerAudio cable
Computer audio in
Control port
Audio input
Speakers
AmplifierComputer in Audio out
Mac adapter
Set the switches as shown in the table below depending on the 
desired resolution. Audio
cable* 
						

							8
Setting up the Projector
Connecting a Video Player 
NOTE: HDTV sources must be
connected to the projector using
either the Y, Pb, Pr input or the
computer IN input.
The following cables can be used to connect a video source:
Composite video cable (RCA x 1)
Component video cable (RCA x 3, not included*)
S-video cable 
AV  a u d i o  c a b l e  
FIGURE 6
Connecting the projector to a video source 
The projector is compatible with these major broadcast video 
standards: NTSC, NTSC 4.43, PAL, PAL-M, PAL-N, and SECAM. 
It automatically adjusts to optimize its performance for the 
incoming video. 
Speakers
AmplifierAudio input PC audio cableAudio out Video
AV  a u d i o  i n Y-Pb/Cb-Pr/Cr
S-video S-video
Video cable Composite
video outComponent
video outS-video outAudio out
(RCA x 1)Video cable
(RCA x 3)*cable
Audio
cable Video cassette recorderVideo disk player
Component video (DVD, HDTV) 
						

							9
Powering up the Projector and Adjusting the Image
NOTE: Always use the power cord 
that shipped with the projector.
1Remove the lens cap.
2Plug the power cord into the side of the projector, then plug it 
into your electrical outlet. A surge-protected power strip is 
recommended.
The Ready indicator on top of the projector lights green, 
indicating the projector is ready to be turned on, and the 
Lamp indicator lights red.
3Press the 
power button on the top of the projector or on the 
remote.
NOTE: The first time you connect 
your computer to the projector, the 
computer may display a message 
stating that new hardware was 
found. The Add New Hardware 
Wizard may appear. Use the Wiz-
ard to load the correct driver (the 
computer considers the projector a 
Plug and Play Monitor). 
The fans start to run, the Lamp indicator dims, and the 
Preparation screen appears. This screen counts down from 
30 seconds, then the image from the active source appears.
4If you connected a video player, turn it on.
The video image should display on the projection screen. If 
a computer source is active, press the 
source button on the 
keypad (page 16) or the 
video button on the remote to dis-
play your video image. 
Use the volume buttons on the remote to adjust the volume. 
The volume dialog box, showing the current volume level 
and mute status, appears for 4 seconds. 
						

							10
Setting up the Projector
5Turn on your computer. 
NOTE: With some computers,
the order in which you power up
the equipment is very important.
Most computers should be turned
on last, after all other peripherals
have been turned on. Refer to your
computer’s documentation to
determine the correct order.
The computer image should display on the projection 
screen. If a video source is active, press the 
source button on 
the keypad or the 
computer button on the remote to display 
your computer ’s image. Make sure your laptop’s external 
video port is activated; see “Portable and Laptop Activation 
Chart” on page 46 for details.
If necessary, make adjustments to the image using the pro-
jector ’s on-screen menus. To open the menus, press the 
menu button on the keypad or remote, then select the 
desired menu. For more information about the menus, see 
page 17.
Turning Off the Projector
If you want to turn off the image for a short period of time, press 
the 
Blank button on the remote. This blanks the screen, but keeps 
the projector running. To exit Blank mode, press the 
Blank button 
again or any other function button.
NOTE: To maximize lamp life,
allow the projector to run for at
least five minutes before turning
it off.
To turn off the projector, press the Pow e r button. The message 
“Power off?” appears on the screen. Press the 
Po w e r button again 
to turn the projector off. The Lamp indicator lights, and the 
Ready indicator dims. The fans run for 90 seconds after the pro-
jector is turned off. When the projector has cooled, the Ready 
indicator lights green, indicating you can turn the projector back 
on if desired.  
						

							11
USING THE PROJECTOR
This section describes how to use and make adjustments to the 
projector. It also provides a reference to the keypad and remote 
buttons and the options available from the on-screen menus.
Adjusting the Image
To focus the image, rotate the focus ring (Figure 7) until the image 
is clear. To zoom the image, rotate the zoom ring. This adjusts the 
image size without affecting focus. Turn the ring in the “Wide” 
direction to make the image larger and in the “Tele” direction to 
make the image smaller.
FIGURE 7
Focus ring and zoom ring
The projector is equipped with self-locking, quick-release eleva-
tor feet (Figure 8).
To raise the projector:
1Lift the front of the projector and lift the feet lock latches on 
both sides of the projector (Figure 8).
2Raise the projector to the height you want, then release the 
latches to lock the elevator feet into position. If necessary, turn 
the feet to fine tune the position and tilt.
zoom ring
focus ring 
						

							12
Using the Projector
F
IGURE 8
Adjusting the height of the projector
Keystone Adjustment
Use this feature to adjust the image vertically and make a squarer 
image.
1Press the 
keystone up/down button on the remote or select Key-
stone in the Screen menu (see page 16 for details on the 
menu).
The message “Keystone” appears.
2Press the 
keystone up button or the point up button to reduce 
the upper part of the image, and press the 
keystone down but-
ton or the 
point down button to reduce the lower part.
FIGURE 9
Adjusting the keystone
foot latch
increasing keystonedecreasing keystone