InFocus Projector IN5312a User Manual

							— 54 — 
Timing Mode Table 
The projector can display multiple resolutions. The following table outlines the resolutions that can be 
displayed by the projector. 
SIGNAL RESOLUTION H-SYNC  
(KHZ) 
V-SYNC 
(HZ) 
COMPOSITE / 
S-VIDEO 
VGA 1/2 
/RGBHV 
(ANALOG) 
HDMI 
(DIGITAL) 
DP 
(DIGITAL) 
NTSC — 15.734 60.0 O — — — 
PAL/SECAM — 15.625 50.0 O — — — 
VESA 
720 x 400 37.9 85.0 — O O O 
640 x 480 31.5 60.0 — O O O 
640 x 480 37.9 72.8 — O O O 
640 x 480 37.5 75.0 — O O O 
640 x 480 43.3 85.0 — O O O 
800 x 600 35.2 56.3 — O O O 
800 x 600 37.9 60.3 — O O O 
800 x 600 46.9 75.0 — O O O 
800 x 600 48.1 72.2 — O O O 
800 x 600 53.7 85.1 — O O O 
1024 x 768 48.4 60.0 — O O O 
1024 x 768 56.5 70.1 — O O O 
1024 x 768 60.0 75.0 — O O O 
1024 x 768 68.7 85.0 — O O O 
1280 x 800 49.7 59.8 — O O O 
1280 x 800 62.8 74.9 — O O O 
1280 x 800 71.6 84.8 — O O O 
1280 x 1024 64.0 60.0 — O O O 
1280 x 1024 80.0 75.0 — O O O 
1280 x 1024 91.1 85.0 — O O O 
1400 x 1050 65.3 60.0 — O O O 
1440 x 900 55.9 60.0 — O O O 
1600 x1200 75.0 60 — O O O 
1920 x1080 67.2 60 — O O O 
1920 x1200[RB] 74.0 60 — O O O 
Apple  
Macintosh 
640 x 480 35.0 66.7 — O O O 
832 x 624 49.7 74.5 — O O O 
1024 x 768 60.2 74.9 — O O O 
1152 x 870 68.7 75.1 — O O O 
SDTV 480i 15.734 60.0 — O O O 
576i 15.625 50.0 — O O O 
EDTV 576p 31.3 50.0 — O O O 
480p 31.5 60.0 — O O O  
						

							  – 55 – 
SIGNAL RESOLUTION H-SYNC  
(KHZ) 
V-SYNC 
(HZ) 
COMPOSITE / 
S-VIDEO 
VGA 1/2 
/RGBHV 
(ANALOG) 
HDMI 
(DIGITAL) 
DP 
(DIGITAL) 
HDTV 
720p 37.5 50.0 — O O O 
720p 45.0 60.0 — O O O 
1080i 33.8 60.0 — O O O 
1080i 28.1 50.0 — O O O 
1080p 27 24.0 — O O O 
1080p 28.13 25.0 — O O O 
1080p 33.75 30.0 — O O O 
1080p 67.5 60.0 — O O O 
1080p 56.3 50.0 — O O O 
O: Frequency supported 
—: Frequency not supported 
(*) VGA supports EDTV/SDTV/HDTV component with an adapter. 
  
						

							— 56 — 
Projector Dimensions 
 
   
						

							  – 57 – 
REGULATORY COMPLIANCE 
FCC Warning 
This equipment has been tested and found to comply with the limits for a Class B digital device 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference when the equipment is operated in a commercial environment. 
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and 
used in accordance with the instruction manual, may cause harmful interference to radio 
communications. Operation of this equipment in a residential area is likely to cause harmful 
interference in which case the user will be required to correct the interference at his/her own expense. 
Changes or modifications not expressly approved by the parties responsible for compliance could 
void the user’s authority to operate the equipment. 
Canada 
This class B digital apparatus complies with Canadian ICES-003. 
WEEE 
 
NOTE: This product is covered electrical and electronic equipment under the European 
Union’s Waste from Electrical and electronic Equipment (“WEEE”) Directive (2002/96/EC). 
The WEEE Directive requires that covered equipment be collected and managed 
separately from typical household waste in all EU member states. Please follow the 
guidance of your local environmental authority or ask the shop where you purchased the 
product for collection or recycling options. 
 
Safety Certifications 
FCC, UL, CUL, CB/CE, KC, CCC, EAC, PSB, NOM., CECP/ECO, SASO TUV-safety, UL-S(Argentina),  
C-Tick/RCM  
						

							— 58 — 
APPENDIX I 
Serial Communication 
The following table describes the serial communication configuration that should be used when 
interfacing to CLI via the serial port. 
Windows HyperTerminal or ProComm are two tools that can be used to send CLI commands across 
the serial port. 
Setting Value 
Bits per second 19200 
Data bits 8 
Parity None 
Stop bits 1 
Flow control None 
Emulation VT100 
 
No Function Command RW Min Max Default Step Parameter 
1 AC Power On 
(Auto power on) 
APO RW 0 1 0 1 0:Disable; 1:Enable 
2 Aspect Ratio ARZ RW 0 5 0 1 
0:Fill 
1:4:3 
2:16:9 
3:Letterbox 
4:Native 
5:2.35:1 
3 Auto Image AIM W n/a 1 1 1 1: Enable 
4 Auto Off Time 
No signal power off AOT RW 0 36 6 1 
0:Never 
1:5 minutes 
2:10 minutes 
3:15 minutes 
… 
35:175 minutes 
36:180 minutes 
5 Auto Source ASC RW 0 1 1 1 0:Disable; 1:Enable 
6 Blank Screen BLK RW 0 1 0 1 0:Disable; 1 Enable 
7 Brightness BRT RW 0 100 50 1 Display Mode=User1 only 
8 Ceiling  
(Projection mode) CEL RW 0 3 0 1 
0:Front 
1:Rear  
2:Ceiling  
3:Ceiling+Rear 
9 Closed Captions: Non- 
Muted CLC RW 0 1 0 1 Off 
On (CC1) 
10 Color CLR RW 0 100 50 1 Video SVideo only 
11 Color Temp TMP RW 0 2 Source 
Specific 1 
Display Mode=User only 
0:Warm  
1:Normal  
2:Cold 
12 Contrast CON RW 0 100 50 1 Display Mode=User1 only  
						

							  – 59 – 
No Function Command RW Min Max Default Step Parameter 
13 Current Source SRC RW 0 20 0 1 
0 = Computer1 
1 = Computer 2 
3 = RGBHV 
4 = HDMI1 
7 = DisplayPort1 
9 = Component1 
11 = Composite 
12 = S-Video 
20 = DVI  
14 Digital Zoom DZM RW -10 10 0 1 Digital Zoom  
15 Error Condition ERR R 0 9 0 1 
0:No error 
1:Lamp not lit after 5 
Attempts 
3:Lamp went out 
unexpectedly 
4:Fan failure 
5:Over-temperature 
8:DMD error 
9:Color wheel 
16 Factory Reset RST W n/a 1 1 1 1:reset 
17 Freeze Screen FRZ RW 0 1 0 1 0:Disable; 1:Enable 
18 Gamma GTB RW 0 5 Source 
Specific 1 
Display Mode=User1 only 
0:1.8 
1:2.0  
2:2.2  
3:2.4 
4:B&W  
5:Linear 
19 Horz. Position HPS RW -5 5 Source 
Specific 1 RGB source only 
(HPS?) to get range 
20 Vert. Position VPS RW -5 5 source 
Specific 1 
RGB source only 
(VPS?) to get range 
(VPS+) 
(VPS-) 
21 Current Lamp Hours 
in Boost mode (370W) LMO R 0 9999 0 1 
Displays the total lamp 
hours the current lamp has 
operated in Boost mode. 
22 
Current Lamp Hours 
in Normal mode 
(330W) 
LME R 0 9999 0 1 
Displays the total lamp 
hours the current lamp has 
operated in Normal mode. 
23 Current Lamp Hours 
in Eco mode (280W) LML R 0 9999 0 1 
Displays the total lamp 
hours the current lamp has 
operated in Eco mode. 
24 Current Lamp Hours 
(All modes) LMP R 0 9999 0 1 
Displays the total lamp 
hours the current lamp has 
operated in all modes. 
25 Reset Lamp Hours LRT W n/a 1 1 1 Resets the lamp counter (all 
modes) to zero. 
26 Lamp hours reset 
counter LMR R 0 9999 0 1 
Displays the number of 
times the lamp counter has 
been reset  
						

							— 60 — 
No Function Command RW Min Max Default Step Parameter 
27 
Total Projection  
Hours 
(lamp1+lamp2+…) 
LMT R 0 9999 0 1 
Displays the total number of 
hours the projector has been 
in operation (all lamps). 
28 Lamp Life LIF R n/a 1500 1500 n/a Lamp life 1500 
29 
Lamp Power Select 
 
High power (Boost) /  
Low power (Normal) / 
Eco power (Eco) 
IPM RW 0 2 1 1 
This Read/Write command 
sets the lamp mode 
0 = Eco 
1 = Normal 
2 = Boost 
33 Language LAN RW 0 26 0 1 
0:English 
1:French 
2:German 
3:Spanish 
4:Portuguese 
5:Simplified Chinese 
6:Traditional Chinese 
7:Italian 
8:Norwegian 
9:Swedish 
10:Dutch 
11:Russian 
12:Polish 
13:Finnish 
14:Greek 
15:Korean 
16:Hungarian 
17:Czech 
18:Arabic 
19:Turkish 
20:Vietnamese 
21:Japanese 
22:Thai 
23:Farsi 
24:Hebrew 
25:Bahasa 
26:Danish 
34 Menu MNU RW 0 1 0 1 0:Clear; 1:Display 
35 Menu Navigation NAV W 0 5 n/a 1 
0:Menu Key 
1:Up Key 
2:Down Key 
3:Select Key 
4:Left Key 
5:Right Key 
36 Menu Transparency TOE RW 0 4 0 5 
0:0% 
1:25% 
2:50% 
3:75% 
4:100% 
37 Mute MTE RW 0 1 0 1 0:Disable; 1:Enable 
38 Overscan OVS RW 0 1 0 1 0:Disable; 1:Enable 
39 Phase(Frequency) MSS RW 0 31 source 
Specific 1 RGB source only 
40 Power PWR RW 0 1 0 1 0:Turn Off 
1:Turn On  
						

							  – 61 – 
No Function Command RW Min Max Default Step Parameter 
41 Presets PST RW 0 8 source 
Specific 1 
Display mode 
0:Presentation 
1:Bright 
2:Game 
3:Movie 
4:TV 
5:sRGB 
6:Blackboard 
7:User1 
8:User2 
42 Projector Firmware 
Ver. FVS R string    LX737-692IF-DPEXX 
43 Projector Info menu PRI W  1  1 1:Display 
Status Menu 
44 Projector Model MDL R string    XGA: IN5312a 
1080P: IN5316HDa 
45 Projector Resolution NRS R string    XGA  
46 Search Screen DSU RW 0 4 0 1 
0:Blue 
1:Black 
2:White 
3:Red  
4:Green 
47 Sharpness SHP RW 0 31 16 1 
Display mode User 1  
only 
same as OSD range 
48 System State SYS R 0 18 0 1 
0:Standby 
2:Start Up 
12:Cooling 
18:Error 
49 Tint TNT RW 0 100 50 1 Tint  
50 Tracking MTS RW -5 5 0 1 RGB source only 
51 Vert. Keystone DKV RW -40 40 0 1 Vertical keystone 
52 Volume VOL RW 0 10 5 1 Volume