InFocus Projector IN5312a User Manual

							— 14 — 
Adjusting the Projector Level 
Take note of the following when setting up the projector: 
 The projector table or stand should be level and sturdy. 
 Position the projector so that it is perpendicular to the screen. 
 Remove and discard the foam spacers on the rear leveling feet before adjusting the 
projection angle. 
 Ensure the cables are in a safe location. You could trip over them.  
1.  To raise the level of the projector, 
twist the leveling feet clockwise. 
 
2.  To lower the level of the projector, 
lift the projector and twist the 
leveling feet counterclockwise. 
 
      
						

							  – 15  – 
Adjusting Projected Imag e Position Using Shift 
 
The Shift feature provides a lens shift function that  can be used to adjust the position of the projected 
image either horizontally or vertically within the range detailed below. 
Shift is a unique system that provi des lens shift while maintaining a much higher ANSI contrast ratio 
than traditional lens shift systems. 
Adjusting the vertical image position 
The vertical image height can be adjusted between 10% and -70% offs et for IN5316HDa (1080P); 0% 
and -60% offset for IN5312a (XGA);  (offset =(O/H) x100%, O: distance from bottom of image to 
center of lens). Note that  the maximum vertical image height  adjustment can be limited by the 
horizontal image position.  Offset is the distance between the lens center line and the bottom of the 
image. The offset is positive if t he lens center line is below the bo ttom of the image. The offset is 
negative if the lens center line is  above the bottom of the image. For  example it is not possible to 
achieve the maximum vertical im age position height detailed above if  the horizontal image position is 
at maximum. Please consult the Shift Range diagram below for further clarification. 
For IN5316HDa (1080P) 
 
 
Screen Height(H) 
10%H  -70% offset
-50% offset
10% offset  
						

							— 16 — 
For IN5312a (XGA)  
 
Adjusting the horizontal image position 
With the lens in the center position the horizontal image position can be adjusted to the left or right by 
up to a maximum of 5% of the image width. Note that the maximum horizontal image height 
adjustment can be limited by the vert ical image position. For example it is not possible to achieve the 
maximum horizontal image position if  the vertical image position is at maximum. Please consult the 
Shift Range diagram below for further clarification. 
 
Screen Height(H) 
-50% offset -60% offset
0% offset 
Distance(H)  
						

							–
17  – Shift 
Range  Diagram 
For IN5316 HDa (1080P)  For IN5312a (XGA) 
Max H image shift=0% offset  
Max W image shift=Wx5%  
When Wx5%, Max image shift= - 2 0% offset  
When 0% offset, Max image shift=Wx0%  Wx5%  
Wx5%  
0 %   offset  
- 20 %   offset  W   Max H image shift= 1 0% offset  
Max W image shift=Wx5%  
When Wx5%, Max image shift= - 1 0% offset  
When  1 0% offset, Max image shift=Wx0%  Wx5%  
Wx5%  
1 0 %   offset  
- 10 %   offset  W     
						

							— 18 — 
Adjusting Zoom, Focus and Keystone 
1.  Use the Zoom ring to 
resize the projected 
image and screen size. 
 
2.  Use the Focus ring to 
sharpen the projected 
image. 
 
3.  Use the KEYSTONE 
buttons (on the 
projector or the remote 
control) to correct 
image trapezoiding 
(wider top or bottom). 
 Remote control and OSD panel 
4.  The keystone control  
appears on the display.      
						

							  – 19 – 
Adjusting the Volume 
1.  Press the Volume 
buttons (on the 
projector or the remote 
control).  
 
The volume control  
appears on the display. 
 
2.  Use the Vol +/- buttons 
(on the projector or the 
remote control).  
3.  Press the MUTE button 
to turn off the audio 
(This feature is only 
available on the 
remote).    
						

							— 20 — 
ON-SCREEN DISPLAY (OSD) MENU SETTINGS 
OSD Menu Controls 
The projector has an OSD that lets you make image adjustments and change various settings.  
Navigating the OSD 
You can use the remote control cursor buttons or the projector keypad to navigate and make changes 
to the OSD.  
 
1. To enter the OSD, press the 
MENU button.  
2. There are three menus. Press the 
cursor ◄► button to move 
through the menus.  
3. Press the cursor ▲▼ button to 
move up and down in a menu.  
4. Press ◄► to change values for 
settings. 
5. Press MENU to access a different 
menu, leave a submenu or close 
the OSD. 
 
Note: 
Depending on the video source, not all items in the OSD are available. For example, the PC Detail 
Adjustment item in the Display menu can only be modified when connected to a PC. Items that are 
not available cannot be accessed and are grayed out.   
						

							  – 21 – 
Setting the OSD Language 
Set the OSD language to your preference before continuing. 
1. Press the MENU button. Press the cursor ◄► button to navigate to Settings 1. Press the 
cursor ▲▼ button to move to the Advanced 1 menu. 
 
2. Press  (Enter) / ► to enter the Advanced 1 sub menu. Press the cursor ▲▼ button 
until Language is highlighted.  
 
3. Press the cursor button until the language you want is highlighted.  
4. Press the MENU button four times to close the OSD.     
						

							— 22 — 
OSD Menu Overview 
Use the following illustration to quickly find a setting or determine the range for a setting. 
MAIN 
MENU 
 
SUB MENU   
 
SETTINGS 
Image  Display Mode    Presentation, Bright, Game, 
Movie, TV, sRGB, Blackboard, 
User 
  Brightness    0~100 
  Contrast    0~100 
  Computer  Horizontal Position  -50~50 (depending on Autolock) 
    Vertical Position  -50~50 (depending on Autolock) 
    Frequency  0~31 
    Tracking  -5~5 
  Auto Image     
  Advanced  Brilliant Color  0~10 
    Sharpness  0~31 
    Gamma  1.8, 2.0, 2.2, 2.4, B&W, Linear 
    Color Temperature  Warm, Normal, Cold 
    Video AGC  Off, On 
    Video Saturation  0~100 
    Video Tint  0~100 
  Color Manager  Red Hue, Saturation, Gain 0~100 
    Green Hue, Saturation, Gain 0~100 
    Blue Hue, Saturation, Gain 0~100 
    Cyan Hue, Saturation, Gain 0~100 
    Magenta Hue, Saturation, Gain 0~100 
    Yellow Hue, Saturation, Gain 0~100 
    White Red, Green, Blue 0~100 
  
						

							  – 23  – 
MAIN 
MENU 
 
SUB MENU   
 
SETTINGS 
Settings 1   Source    Source   Reference Input Source Select 
(IR/Keypad) 
    Projection       Normal, Real, Ceiling, Real+Ceiling 
    Aspect Ratio       Fill, 4:3, 16:9, Letter Box, Native, 2.35:1 
  Keystone      -40~40 
  Digital Zoom      -10~10 
  Audio  Volume    0~10 
     Mute    Off, On 
    Advanced 1    Language    English, Français, Deutsch, Español, 
Português, 簡体中文, 繁體中文, Italiano, 
Norsk, Svenska, Nederlands,  Русский, 
Polski, Suomi,  Ελληνικά, 한국어, Magyar, 
Č eština,  ةيبرعلا, Türkçe, Vi ệt, 日本語, ไทย , 
یسراف , עברית , Bahasa Indonesia, Dansk 
        Security Lock    Off, On 
       Blank Screen    Blank, Red, Green, Blue, White 
       Splash Logo    Std., Off, User 
     Closed Captioning   Off, On 
     KeypadLock   Off, On 
       3D Setting  3D  Off, DLP-Link, IR 
        3D Sync Invert  Off, On 
         3D Format  Frame Sequential, Top/Bottom, Side-By-
Side, Frame Packing (3D Frame Packing 
HDMI source only) 
     Screen Capture    
    Advanced 2    Test Pattern    None, RGB Ramp, Color Bars, Step Bars, 
Checkbox, Grid, Horizontal Line 
        H Image Shift     -50~50 
       V Image Shift    -50~50