InFocus Projector IN5110 User Manual

Regulatory models: W59
5100
QR80421
IN5110  
User’s Guide 

1
Declaration of Conformity
Manufacturer: InFocus Corporation, 13190 SW 68th Parkway, Suite 200, Portland, 
Oregon 97223 USA 
 
We declare under our sole responsibility that this projector conform to the following 
dire
 ctives and norms:   
EMC Directive 2004/108/EC  
EMC: EN 55022  
           EN 55024  
 EN 61000-3-2  
 EN 61000-3-3  
Low Voltage Directive 2006/95/EC  
Safety: IEC 60950-1: 1
st Edition   
Trademarks
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple...

WARNING: Do not look into laser beam emitted from the front of the 
remote control.
CAUTION:  Use of controls or adjustments  or performance of procedures 
other than those specified herein  may result in hazardous radiation 
exposure. Class 2 Laser product;  maximum output 1mW; wavelength 
650nm.
[Class 2 Laser Product]  Wavelength 650nm; Maximum output 1mW; No 
beam divergence. 
[Laser Diode]  Wave length 650nm; Maximum  power 7mW; Beam diver-
gence 33deg (perpendicular)/8deg (parallel).
Location of...

3
Table of Contents 
 
Introduction 5
Included Items  5
Positioning the projector  7
Connecting a computer  8
Required computer connections  8
Displaying a computer image  10
Adjusting the image  11
Connecting a video device  12
Displaying a video image  13
Shutting down the projector  15
Troubleshooting your setup  15
Using the keypad buttons  22
Using the remote control  23
Using the audio  24
Optimizing computer images  25
Presentation features  25
Optimizing video images  26
Customizing the projector...

4
Important Operating Considerations for Safety
• Place the projector in a horizontal position no greater than 8 degrees off axis.
• Locate the projector in a well-ventilated are a
  without any obstructions 
to intake or exhaust vents. Do not pl ace the projector on a tablecloth or 
other soft covering that may block the vents. 
• Locate the projector at least 4 (1.2  m) away from any 
 heating or cooling 
vents.
• Use only approved ceiling mounts.
•
Warning:  To prevent eye injury if the  projector is...

5
Introduction
Your new multimedia projector provides three computer, three video, and 
four audio inputs, one audio output,  and RS-232 and Network control. It 
has WUXGA 1920 x 1200 resolution. The projec tor is easy to connect, easy to 
use, and easy to maintain. 
Product specifications
To read the latest specifications on your multimedia projector, be sure to 
visit our website. Web address information is located on the back inside 
cover of this User’s Guide.
Online Registration
Register your...

6
Connector Panel
The projector provides three computer and three video connection options: 
•one VGA computer
• one HDMI™ (High Definition Multimedia Interface)*
• one component BNC (G/Y, B/C
B/PB, R/CR/PR, H, V)
• one component RCA video (Pr, Pb, Y)
•one S-video
•one composite RCA video
The projector provides computer and  video co
nnectors 
 for audio support: 
• two composite RCA stereo audio (L, R)
• one audio out
•two audio ins 
The projector also provides the following connectors:
• one wired...

7
Positioning the projector
To determine where to position the projector, consider the size and shape of 
your screen, the location of your power outlets, and the distance between 
the projector and the rest of your eq uipment. Here are some general guide-
lines:
• Position the projector on a flat surfac e at a ri

ght angle to the screen. The 
projector must be at least 3 feet  (0.9m) from the projection screen.
• Position the projector within 10 feet (3m) of your power source and  with
 in 6 feet...

8
Connecting a computer
Required computer connections
Connect one end of the VGA computer cable to the Computer 2 connector 
on the projector. Connect the other end  to the video port on your computer. 
If you are using a desktop computer, yo u first need to disconnect the moni-
tor cable from the computer’s video port. 
Connect the black power cable to the co nnec

tor on the back of the projector 
and to your electrical outlet.
 
NOTE : Always use the power cable that shipped with the projector....

9
If you are using a desktop computer and want to see the image on your 
computer screen as well as on the projection screen, plug the monitor cable 
to the  Monitor out  connector on the projector. 
You can control the projector from an  LCD control 
 panel, touch screen, or 
other control device or computer by  connecting an RS-232 cable to the pro-
jector’s  Serial Control  connec
 tor. Specific RS-232 commands can be found in 
the Service and Support section of our website and in the Appendix....