InFocus Projector In2112 User Manual

							40
Maintenance
Cleaning the lens
1Turn the projector off and unplug the power cord.
2Slide open the lens cover, if the lens is covered.
3Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
• Avoid using an excessive amount of cleaner, and don’t apply the 
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh 
chemicals might scratch the lens.
4Lightly wipe the cleaning cloth over the lens in a circular motion.
WARNINGS: 
• Turn the projector off and unplug power cord before cleaning any part 
of the projector.
• Do not open any cover on the projector, except the lamp cover.
• Do not attempt to service this product yourself as opening and remov-
ing covers may expose you to dangerous voltage and other hazards. 
Refer all servicing to qualified service personnel. 
						

							41
Replacing the projection lamp
The lamp hours timer in the Projector Info menu counts the number of 
hours the lamp has been in use. Twenty hours before the lamp life expires, 
the message “Replace lamp” appears on the screen at startup.
•NOTE: Be sure to use the InFocus lamp module designed for this 
projector. You can order new lamps from www.infocus.com (in select 
areas), your retailer or your dealer. Only genuine InFocus lamps are tested 
for use in this projector. Use of non InFocus lamps may cause electrical 
shock and fire, and may void the projector warranty.  InFocus is not 
liable for the performance, safety or certification of any other lamps.
WARNINGS:
• The projector uses a high-pressure mercury glass lamp.  The lamp may 
fail prematurely, or it may rupture with a popping sound if jolted, 
scratched, or handled while hot.  The risk of lamp failure or rupture 
also increases as the lamp age increases; please replace the lamp when 
you see the “Replace Lamp” message.
• To avoid burns, allow the projector to cool for at least 60 minutes before 
you replace the lamp.
• Unplug the power cord before replacing the lamp.
• Do not drop the lamp module. The glass may shatter and cause injury.
• Do not touch the glass surface of the lamp module. Fingerprints can 
obscure projection sharpness and may cause the glass to shatter.
• Be extremely careful when removing the lamp housing. In the unlikely 
event that the lamp ruptures, small glass fragments may be generated. 
The lamp module is designed to contain most of these fragments, but 
use caution when removing it. 
• Before replacing a ruptured lamp, clean the lamp compartment and 
dispose of cleaning materials. Wash hands after lamp replacement. 
• When replacing the lamp while the projector is ceiling-mounted, wear 
protective eyewear to prevent eye injury.
• Hg – Lamp contains mercury. Manage in accordance with local 
disposal laws. See www.lamprecycle.org.
1Turn off the projector and unplug the power cord.
2Wait 60 minutes to allow the projector to cool thoroughly.
3Remove the top front cover by (a) removing the screws on the two sides 
of the projector, and (b) lifting the top front cover off.
Turn off and 
unplug projectorWait 60 
minutes
(a) (a)(b) 
						

							42
4Loosen the two captive screws that attach the lamp housing to the 
projector.
5Using the handle, carefully remove the lamp housing. Dispose of the 
lamp in an environmentally proper manner in accordance with local 
disposal laws.
6Install the new lamp housing, pressing the lamp into place.
7Tighten the captive screws.
8Replace the top front cover and tighten both screws.
9Plug in the power cord and press the Power button to turn the projector 
back on.
10To reset the lamp hour timer, navigate to the Status and Service menu and 
select Reset Lamp Hours. See 
page 32 for details.
Using the security lock
The projector has a security lock for use with a Cable Lock System. Refer to 
the information that came with the lock for instructions on how to use it.
Security Lock 
						

							43
INDEX
Numerics
16x9 vs 4x3 12
A
Aspect Ratio 12, 13
Audio In Computer connector 9
Audio Out connector 23
C
cable box 12
Computer In connector 8
Connecting
external speakers 23
connecting
computer 8
video device 12
Connecting a computer source 8
contacting InFocus 21
customer service contact information 21
D
Digital Zoom 27
Displaying an image 9
Dynamic Messaging 25
F
focus 11
H
Help 32
K
keypad buttons 24
Keystone 18
L
laptop video port activation 10
LitePort
Using LitePort 37
M
menu usage 26Monitor Out connector 9
N
Network
Using Network Functions 33
O
Optimizing computer image 24
Optimizing video images 25
P
Position the projector 6
Power connector 8
power cord 8
Presentation features 24
Projector
keypad buttons 24
menus 26
projector
connecting computers 8
connecting video devices 12
positioning 6
setting up 6
shutting down 14
troubleshooting problems 14
R
remote control 22
S
Scheduled Tasks Page 35
Screen Aspect 12
Screen Save 14
shutting down the projector 14
speakers, connecting external 23
S-video connector 12
T
Troubleshooting Network Functions 36
TV tuner 12
U
USB 8 
						

							44
V
Viewing a Slide Show 37
Volume button 23
W
warranty 21
Z
zoom 11