InFocus Projector In2112 User Manual

							20
The video embedded in my PowerPoint presentation 
does not play on the screenTurn off the internal LCD display on your laptopEmbedded video plays correctly
Lamp won’t turn on, Temperature light is onMake sure vents aren’t blocked, turn the projector off 
and allow it to cool for one minute. Lamp turns on
Problem Solution Result
AB
AB
Temperature light
Startup
Screen 
						

							21
Still need assistance?
If you need assistance, visit our support website at www.infocus.com/support 
or call us. Check out the How To section for additional information on using 
this projector for home theater or gaming applications. 
This product is backed by a limited warranty. An extended warranty plan 
may be purchased from your dealer. When sending the projector in for 
repair, we recommend shipping the unit in its original packing material, or 
having a professional packaging company pack the unit. Please insure your 
shipment for its full value.
“Replace lamp” message appears at startup, lamp 
won’t turn on, Lamp light is turned onLamp must be replaced (see page 41)Lamp turns on
Problem Solution Result
Lamp light
Top front cover
Replace lamp
Startup
Screen 
						

							22
Using the remote control
The remote uses two (2) provided AA batteries. You can install the batteries 
by removing the cover from the remote’s back, aligning the + and - ends of 
the batteries, sliding them into place, and then replacing the cover.
Caution: 
• When replacing the batteries, be aware that using batteries other than 
the type provided with the projector may risk severe damage to the 
remote. When disposing of the batteries, be sure to do so in an 
environmentally proper manner.
• If the remote control gets wet, wipe it dry immediately.
• Avoid excessive heat and humidity.
• Ensure the batteries’ polarity (+/-) is aligned correctly.
• Do not mix new and old batteries together, or different types of 
batteries together.
• Replace the batteries as soon as they run out.
• Remove batteries from the remote control when storing or not in use 
for a prolonged period.
To operate, point the remote at the projector (not at the computer). The 
range of optimum operation is about 30’ (9m).
Press the remote’s Power button to turn the projector on and off (see page 14 for shutdown information).
Press the remote’s Menu button to open the projector’s menu system. Use 
the arrow buttons to navigate, and the Select button to select features and 
adjust values in the menus. See 
page 26 for more information on the menus.
The remote also has:
•Help button to access the projector’s help feature (see page 32).
•Volume buttons to adjust the sound.
•Custom button that can be assigned to a special function, like Blank 
Screen or Freeze (see 
page 29).
•Source button to switch between sources.
•Blank button to blank the screen.
•Presets button to select stored settings (see page 27).
•Mute button to silence the audio.
•Auto Image button to resynchronize the projector to the source.
•Resize button to switch among aspect ratios (see page 27).
Troubleshooting the remote
• Make sure the batteries are installed in the proper orientation and are 
not dead.
• Make sure you’re pointing the remote at the projector or the screen, not 
the computer, and are within the remote range of 30’ (9m). For best 
results, point the remote at the projector.
Navigation 
buttons 
						

							23
Using the audio
Using the projector’s speakers
To use the projector’s speaker, connect your source to the Audio In 
Computer or Video connectors.
To adjust the volume, press the Volume buttons on the keypad or remote.
Troubleshooting Audio
If you aren’t hearing the audio, check the following:
• Make sure the audio cable is connected to the correct audio in 
connector, Computer or Video.
• Make sure the volume is turned up enough. Press the Volume button on 
the keypad or remote.
• Make sure you are connected to the corresponding audio in for your 
source. 
• Make sure that you are connected to an audio out connector on the 
source as opposed to a line in or microphone connector.
• Adjust the audio source.
• If playing a video, make sure the playback has not been paused.
Connecting external speakers
The projector can be attached to external amplified speakers by connecting 
a 3.5mm stereo audio cable from the Audio Out connector on the projector to 
the amplified speakers. Alternatively, you can bypass the projector’s audio 
system and connect the audio directly from your source to a stereo or home 
theater system.
Connect audio cable
Adjust volume
External speakers 
with own power 
source
Speaker 
cable 
						

							24
Using the keypad buttons
Most buttons are described in detail in other sections, but here is an 
overview of their functions:
Power–turns the projector on and off (page 8).
Auto Image–resynchronize the projector to the source.
Presets–cycles through the available preset settings (page 27).
Menu–opens the onscreen menus (page 26).
Select–confirms choices made in the menus (page 26).
Up/Down/Left/Right arrows–navigates to and adjusts settings in the menus 
(
page 26).
Volume–adjusts sound (page 23).
Source–changes the active source (page 8).
Help–button to access the projector’s help feature (page 32)
Keystone–adjusts squareness of the image (page 11).
Optimizing computer images
After the projector is running and the image is on the screen, you can 
optimize the image using the onscreen menus. For general information on 
using the menus, see 
page 26.
• Adjust the Keystone, Contrast, or Brightness in the Basic Picture menu 
(
page 27).
• Change the Aspect Ratio. Choose the option that best fits your input 
source (
page 27).
• Adjust the Color Temperature in the Advanced Picture menu 
(
page 28).
• Adjust the Phase, Tracking, or Horizontal or Vertical position in the 
Advanced Picture menu (
page 28).
• Once you have optimized the image for a particular source, you can 
save the settings using Presets. This allows you to quickly recall these 
settings later (
page 27).
Presentation features
Several features are provided to make giving presentations easier. Here is 
an overview, details are found in the menu section.
• The Custom key allows you to assign various features to the button. 
The default effect is Source Info, which displays information about the 
projector and current source. See 
page 29 for details.
• The Search Screen option lets you change the appearance of the blank 
screen and start up screen (
page 30).
• Two options, Auto Off and Screen Save Time, are provided to 
automatically shut down the projector after several minutes of 
inactivity or display a black screen. This helps preserve lamp life 
(
page 29).
Menu navigation 
buttons 
						

							25
Optimizing video images
After your video device is connected properly and the image is on the 
screen, you can optimize the image using the onscreen menus. For general 
information on using the menus, see 
page 26.
• Adjust the Keystone, Contrast, Brightness, Color, Tint or Sharpness in 
the Basic Picture menu (page 27).
• Change the Aspect Ratio. Choose the option that best fits your input 
source (
page 27).
• Adjust the Color Temperature. Select a listed warmth value (page 28).
• Turn on Overscan to remove noise on the edges of the image (page 28).
Customizing the projector
You can customize the projector for your specific setup and needs. See 
page 29 to page 30 for details on these features.
• For rear projection, turn Rear Project on in the Setup menu.
• For ceiling mounted projection, turn Ceiling Mount on in the Setup 
menu.
• Specify which source the projector checks first for active video during  power-up.
• Specify the function of the Custom key on the remote.
• Turn the projector’s display messages on and off.
• Turn on power saving features.
• Specify appearance of blank screen and startup screen.
• Specify the language viewed on the menus.
Dynamic Messaging
Using command codes, text messages can be sent for display by the 
projector (and all other InFocus projectors with the Dynamic Messaging 
feature) over a network or serial connection. Text is shown on top of 
whatever else is being displayed, and can be shown in ticker tape format or 
in a box, with optional beep tone alert. This is a great way to display urgent 
alert messages to employees, and simply requires a connection to the 
projector’s RS-232 serial control or LAN connector. Command codes for 
executing Dynamic Messaging are available on our website at 
www.infocus.com/support. 
						

							26
Using the menus
To open the menus, press the Menu button on the keypad or remote. (The 
menus automatically close after 60 seconds if no buttons are pressed.) Use 
the arrow buttons to move up and down to highlight the desired menu, 
then press the Select button.
To change a menu setting, highlight it, press Select, then use the arrow 
buttons to adjust the value or select an option or turn the feature on or off. 
Press Select to confirm your changes. Use the arrow buttons to navigate to 
another setting. When your adjustments are complete, press Menu to access 
a different menu; press the Menu button at any time to navigate to the 
higher-level menu and ultimately close the menus.
The menus are grouped by usage:
• The Basic Picture menu provides common image adjustments.
• The Advanced Picture menu provides more complex image 
adjustments.
• The Setup menu provides set-up type adjustments that are not changed 
often.
• The Status and Service menu provides information about the projector 
and source.
Menu navigation 
buttons
Basic Picture menu Advanced Picture menu
Setup menu Status and Service menu 
						

							27
Basic Picture menu
To adjust the following settings, highlight the setting, press Select, use the 
arrow buttons to adjust the values, then press Select to confirm the changes.
Brightness: Changes the intensity of the image.
Contrast: Controls the degree of difference between the lightest and darkest 
parts of the picture and changes the amount of black and white in the 
image.
Sharpness: Changes the clarity of the edges of a video image. Select a 
sharpness setting.
Color: Adjusts a video image from black and white to fully saturated color. 
The color setting applies to video sources only.
Tint: Adjusts the red-green color balance in the image of NTSC video 
images. The tint setting applies to NTSC video sources only.
Auto Image: Forces the projector to reacquire and lock to the input signal. 
This is useful when signal quality is marginal.
Aspect Ratio: Aspect ratio is the ratio of the image width to image height. TV 
screens are usually 4:3. HDTV and most DVDs are 16:9.
Select Auto to have the projector choose the ratio. Choose Native to see the 
unmodified input with no resizing by the projector. Select 16:9 to watch 
enhanced widescreen DVDs.
For more information regarding Aspect Ratio, see page 13.
Apply Preset...: Presets are provided that optimize the projector for 
displaying computer presentations and video images under certain 
conditions.
There is also a user-definable preset. To set this preset, adjust the image and 
select Save User in the Presets menu. You can recall these settings in the 
future by selecting the User preset.
Keystone: Adjusts the image vertically and makes a squarer image.
Digital Zoom: Changes the size of projector’s display area. If the display area 
has been resized by this setting, it can be moved by changing the Horz Shift 
and Vert Shift settings.
Horz Shift/Vert Shift: Moves the display area horizontally or vertically if its 
size has been changed by the Digital Zoom setting.
.
Basic Picture menu
Aspect ratio
Increasing keystone
Decreasing keystone 
						

							28
Advanced Picture menu
BrilliantColor™: Produces an expanded onscreen color spectrum that 
delivers enhanced color saturation for bright, true-to-life images. Choose 
Normal Look for most video sources and Bright Look for most computer 
sources.
White Peaking: (video sources only) Increases the brightness of whites that 
are near 100%.
Color Temperature: Changes the intensity of the colors. Select a listed 
relative warmth value.
Force Wide: When this is off, the analog locking algorithms choose the 
standard mode resolution (4:3) as the preferred default resolution. When 
this is on, the analog locking algorithms choose wide mode resolution 
(16:10) as the preferred default resolution.
Overscan: Removes noise around the video image.
Phase: Adjusts the horizontal phase of a computer source.
Sync Threshold: (progressive signals only) If a hardware device, such as a 
DVD player, is not syncing properly with the projector, select this option to 
help it to sync when connected to the projector.
Tracking: Adjusts the vertical scan of a computer source.
Color Space: This option applies to computer and component video sources. 
It allows you to select a color space that has been specifically tuned for the 
input signal. When Auto is selected, the projector automatically determines 
the standard. To choose a different setting, turn off Auto, then choose RGB 
for computer sources or choose either REC709 or REC601 for component 
video sources.
Noise Reduction:Reduces temporal and/or spatial noise in the image.
Set Black Level...: Analyzes the current input image and calculates an offset 
value which is then added to the analog to digital converter black level 
value. This ensures optimum black level for each analog source.
Detect Film: Controls film mode detection, and determines whether the 
original source of the input video was film or video.
Gamma: Select the appropriate gamma from among Video, Film, Bright, and 
CRT.
Color Gamut: Sets the color gamut of the input signal.
Color Gain Settings: Adjusts the gain of the red, green, or blue channel of the 
image.
Color Offset Settings: Adjusts the offset of the red, green, or blue channel of 
the image.
Horizontal/Vertical Position: Adjusts the position of a computer source.
.
Advanced Picture menu 
						

							29
Setup menu
Language: Allows you to select a language for the onscreen display.
Network: (IN2114 & IN2116 only) Allows you to setup network settings. See 
page 33 for details on network configuration and operation.
•DHCP: Turns the DHCP on or off.
•IP Address: Assign Network IP Address. 
•Subnet Mask: Assign Network Subnet Mask.
•Default Gateway: Assign Network Default Gateway.
•WINS Host Name Lookup: Turns WINS Host Name Lookup on or off.
•Host Name: Shows the host name.
•MAC Address: Shows network MAC Address value.
•Show Network Messages: Turns network messages on or off. Network 
messages display the projector’s IP address (and host name if enabled) 
when the projector is also displaying source messages.
•Restart Network…: Restarts the network.
•Network Factory Reset…: Performs factory reset.
Key Click: Turns the key click sound on or off. When this setting is on, 
pressing keys on the keypad causes the projector’s speaker to play a “click” 
sound.
Custom Key: Allows you to assign a different function to the Custom button, 
allowing you to quickly and easily use the effect. Highlight an effect and 
press Select to choose a different one.
•Source Info: The default action. Shows the Source Info menu.
•Projector Info: Shows the Projector Info menu.
•Aspect Ratio: Sets the ratio of image width to image height (see page 13 and page 27).
•Auto Image: Resynchronizes the projector to the source (page 24).
•Overscan: Removes noise around the image.
•Blank Screen: Displays an empty screen.
•Freeze Screen: Pauses the projected image.
•Mute: Turns off all sound.
•AV Mute: Enables or disables AV Mute function.
•Source: Cycles through available sources.
•Closed Captions: Enables or disables Closed Captions.
Blank Key: Select what to display when the blank key on the remote is 
depressed: your custom snapshot, a solid color screen (blue, black or white), 
the factory logo screen, a timer, or test patterns. The timer option is useful 
for classroom tests or break times during meetings.
Source Keys: Enables or disables Source Keys on the optional Commander-2 
remote.
AC Power On: When this feature is on, the projector automatically turns on 
when electrical power is connected. This allows control of ceiling mounted 
projectors with a wall power switch.
Auto Off Time: Automatically turns the projector off after no signals are 
detected for a preset number of minutes. If an active signal is received 
before the projector powers down, the image will be displayed.
Screen Save Time: Automatically blanks the screen with a black color after no 
signals are detected for a preset number of minutes. The image returns 
when an active source is detected or a remote or keypad button is pressed.
Sleep Timer: Allows the projector to automatically power off after it has been 
on for a specified amount of time.
Always-On Functions: Allows you to control which projector functions will 
work even when the projector is in standby (powered off but connected to 
AC Power). Press Up or Down to highlight the function you want to 
change, then press select or left and right to change the function to either 
Yes or No. Press menu when done.  Note that some functions must always 
have the same value; in this case when you change one value, other values 
in the submenu may also change automatically.
Lamp Low Power: Toggles between on and off. Turn it on to lower the light 
output of the lamp. This also lowers the fan speed, making the projector 
quieter.
Power Sounds: Controls whether the projector makes a sound when 
powered on and off.
Internal Speakers: Allows the user to turn on and off the internal speakers.