InFocus Projector In2112 User Manual

							10
Displaying an image
Touch the Power button on the keypad or the remote.
The Power button blinks green and the fans start to run. When the lamp 
turns on, the start up screen will display and the Power button will become 
solid green. It can take a minute for the image to achieve full brightness.
No start up screen? Get help on page 15.
Slide the lens cover to the side, if it is covering the lens.
Turn on your computer or video device.
The image should appear on the projection screen. If it doesn’t, press the 
Source button on the projector’s keypad or remote.
If you are using a VGA cable to connect your computer to the projector:
If using a laptop, make sure its external video port is active.
Many laptops do not automatically turn on their external video port when a 
projector is connected. Usually a key combination like Fn + F8 or CRT/LCD 
key turns the external display on and off. Locate a function key labeled 
CRT/LCD or a function key with a monitor symbol. Press Fn and the 
labeled function key simultaneously. Refer to your laptop’s documentation 
for more information about your laptop’s key combination or go to the 
InFocus website at: http://www.infocus.com/Support/LaptopActivation.aspx. 
No laptop image? Try pressing the Auto Image button on the keypad.
Press Power button
Turn on computer or 
video device
Activate laptop’s external port
Monitor key or 
LCD/CRT key
Fn key 
						

							11
Adjusting the image
If necessary, adjust the height of the projector by pressing the elevator foot 
release button to extend the foot.
Rotate the elevator feet for granular adjustment of the projector’s height. 
Avoid placing your hands near the hot exhaust vent at the side of the 
projector. 
Avoid placing your hands near the hot exhaust vent at the side of the 
projector.
Position the projector to the desired distance from the screen at a 90 degree 
angle to the screen. See 
page 6 for a table listing to screen sizes and 
distances.
Adjust the zoom or focus. 
If the image is not square, first make sure that the projector is perpendicular 
to the screen. To reduce the size of the top edge of the image, press the top 
Keystone button. To reduce the size of the bottom edge of the image, press 
the bottom Keystone button.
If the left or right side of the screen is larger or smaller than the other, you 
can turn the projector to the left or to the right a few degrees to square the 
image. See 
page 6 for details.
Adjust the Contrast or Brightness in the Basic Picture menu. See page 27 for 
help with these menu adjustments.
Adjust height
Adjust distance
Adjust zoom and focus
Adjust keystone 
						

							12
Connecting a video device
You can connect video devices such as VCRs, DVD players, camcorders, 
digital cameras, video game consoles, HDTV receivers, and TV tuners to the 
projector. You can connect the audio directly to the projector to get sound 
from the built-in speaker, or you can bypass the projector’s audio system 
and connect the audio directly from your source to a stereo or home theater 
system.
You can connect the projector to most video devices that can output video. 
You cannot directly connect the coaxial cable that enters your house from a 
cable or satellite company; the signal must pass through a tuner first. 
Examples of tuners are digital cable boxes, VCRs, digital video recorders, 
and satellite TV boxes. Basically, any device that can change channels is 
considered a tuner.
Although the aspect ratio is automatically selected by the projector based on 
the signal input, you can change the aspect ratio, if desired. The projector’s 
Aspect Ratio setting is accessed through the Resize button on the remote or 
through the projector’s Basic Picture Menu. See 
page 27 for more 
information.
Video device connections
No video cables are provided with the projector. You can order cables from 
InFocus or use your own.
Composite video connection
Plug the composite video cable’s yellow connector into the video out 
connector on the video device. Plug the other yellow connector into the 
yellow Composite connector on the projector.
Plug the white connector of a Mini-plug audio Y-cable into the left audio 
out connector on the video device and plug the red connector into the right 
audio out connector on the video device. Plug the other end of the cable into 
the associated audio in connector on the projector.
Keep in mind that video output from composite connections is not as high 
quality as S-video.
S-video connection
If your video device uses a round, four-prong S-video connector, plug an S-
video cable into the S-video connector on your video device and into the S-
video connector on the projector. Use the audio cable as described above.
Keep in mind that video output from S-video connections is not as high 
quality as component.
VGA connection
If your video device has a 15-pin VGA output, plug one end of the included 
computer cable into the VGA connector on your video source. This 
connector may be labeled “To Monitor” on the video source. Plug the 
computer cable into the VGA 1 or VGA 2 connector on the projector.
Component video connection
A Component to VGA adapter can be used in conjunction with the VGA 
connectors. Plug the component cable into the video device. Plug the other 
end of the component cable into the adapter and plug the adapter into the 
VGA 1 or VGA 2 connector.
Component offers the highest quality video output. 
						

							13
What is Aspect Ratio?
Aspect ratio is the ratio of the image width to image height. Standard TV 
screens and older laptops are 4:3; HDTV and most DVDs are 16:9; and 
widescreen computers are 16:10. If you are projecting onto a screen, the 
size/shape of the screen will influence the aspect ratio you decide to use. If 
you are projecting onto a blank wall, there are no screen size restrictions. 
What you plan to project will also help you choose between 4:3, 16:9 or 
16:10. Many TV shows are 4:3, while most movies are 16:9.
If you have a 16:9 screen then you should select an aspect ratio of 16:9 for 
widescreen movies or HDTV, and Native for 4:3 content. If you have a 4:3 
screen you should still use 16:9 for widescreen movies or HDTV, but you 
also have the option of using either 4:3 (to fill the screen) or Native (for 
direct pixel mapping) for 4:3 content. Force Wide can also be enabled to 
automatically resize less common aspect ratios to 16:10.
 
4:3 screen 16:9 screen
4:3 
mode
16:9 
mode
Native 
mode 
						

							14
Shutting down the projector
Screen Save Time
You can make the black screen appear after a preset number of minutes by 
turning on the Screen Save Time feature in the Setup menu. See 
page 29.
Auto Off Time
The projector has an Auto Off Time feature that automatically turns the 
projector off if no active sources are detected and no user interaction with 
the projector is performed for 30 minutes. By default, this feature is off. You 
can change the length of time, see 
page 29.
Turning off the projector
To turn the projector off, press the Power button on the remote or keypad. 
The lamp turns off and the LED blinks amber for 10 seconds while the fans 
continue to run to cool the lamp. When the lamp has cooled, the LED lights 
amber and the fans stop. Unplug the power cable to completely power off 
the projector.
Troubleshooting your setup
The Status Indicator Panel on top of the projector indicates the state of the 
projector and is a helpful when troubleshooting
.
Table 3: Status indicator light behavior and meaning
IconMeaning
Power, solid amber
Power, blinking green
Power, solid green
Power, blinking amber
The projector is plugged in.
The power button has been pressed and 
the software is initializing.
The projector is on and initialized.
The power button has been pressed to 
turn the projector off and the fans are 
running to cool the projector.
TemperatureThe projector is too hot. Make sure the 
vents aren’t blocked (see page 20). Turn the projector off and wait one minute, 
then turn the projector on again. Contact 
Technical Support if the problem persists. 
Visit www.infocus.com/support to contact 
service.
LampTurn the projector off and wait one 
minute, then turn the projector on again. 
If the lamp light turns on again, replace the 
lamp and reset the lamp timer
 (page 42). 
Wrench/ServiceTurn the projector off and wait one 
minute, then turn the projector on again. 
If the service lamp turns on again, service 
is required. Visit www.infocus.com/
support to contact service. 
						

							15
Problem SolutionResult
No start up screenPlug power cord into the projector then
press power button
Correct image
Only start up screen appearsPress the Source button Activate the laptop’s external port
Computer image projected
Startup
Screen
A
Startup
Screen
Restart laptop
A 
						

							16
ProblemSolutionResult
No computer image, just the words “Signal out of 
range” Press the Auto Image button on the keypad or remote. To 
adjust computer refresh rate, go to Control Panel > Display > 
Settings > Advanced > Adapter (location varies by operating 
system).
You may also need to set a different resolution on your 
computer, as shown in the following problem, “image fuzzy or 
cropped”
Computer image projected
Only my laptop’s background appears, not the 
Desktop iconsWindows - Disable “Extend my Windows Desktop” in Control 
Panel > Display > Settings > Display 2 (location varies by 
operating system)Background and Desktop projected
A
Signal out of
the range
A
 
Uncheck this 
option, then 
click Apply
A 
						

							17
Image fuzzy or cropped Set your computer’s display resolution to the native 
resolution of the projector (Start > Settings > Control 
Panel > Display > Settings tab) 
Image clear and not cropped
Image not centered on screenMove projector and adjust zoomCorrect image
Problem Solution Result
AA
For a laptop, 
disable laptop 
monitor or turn-
on dual-display 
mode
A
A 
						

							18
Image not squareAdjust Keystone in the Basic Picture menuSquare image
Image not sharpAdjust Sharpness in the Basic Picture menuCorrect image
Image does not fit 4:3 or 16:9 screenChange aspect ratio to 4:3 or 16:9 in Basic 
Picture>Aspect Ratio menu
Correct image
Problem Solution Result 
						

							19
Image upside downTurn off Ceiling Mount in Setup menuCorrect image
Image reversed left to rightTurn off Rear Project in Setup menuCorrect image 
Projected colors don’t match sourceAdjust color, tint, brightness, contrast in the Basic 
Picture menu and/or color space in the Advanced 
Picture menu
Correct image
Problem Solution Result
A
A
COLORCOLOR