InFocus Projector IN1126 User Manual

							
User’s Manual 
– 34 – 
Cleaning the Projector 
Cleaning the projector to remove dust and grime will help ensure trouble-free operation.  
Warning: 
1. Be sure to turn off and unplug the projector at  least 60 minutes before cleaning. Failure to do so 
could result in a severe burn. 
2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings 
on the projector.  
3. If a little water gets into the projector interior  while cleaning, leave unplugged in a well-ventilated 
room for several hours before using. 
4. If a lot of water gets into the projector inte rior when cleaning, have the projector serviced. 
Cleaning the Lens 
You can purchase optic lens cleaner from most camera stores . Refer to the following to clean the pro-
jector lens. 
1. Apply a little optic lens cleaner to a clean soft  cloth. (Do not apply the cleaner directly to the 
lens.) 
2. Lightly wipe the lens in a circular motion. 
Caution: 
1.  Do not use abrasive cleaners or solvents. 
2. To prevent discoloration  or fading, avoid getting cleaner on the projector case. 
Cleaning the Case 
Refer to the following to clean the projector case. 
1. Wipe off dust with a clean dampened cloth. 
2. Moisten the cloth with warm water and  mild detergent, and then wipe the case. 
3. Rinse all detergent from the cloth and wipe the projector again. 
Caution: 
To prevent discoloration or fading of the case, do not use abrasive  alcohol-based cleaners.  
						

							
IN1124/IN1126 – User’s Manual 
Using the Security Lock 
If you are concerned about security, attach the projector to a permanent object with the Security slot 
and a security cable.  
 
Note: 
Contact your vendor for details  on purchasing a security cable.  
   – 35  –  
						

							
User’s Manual 
– 36 – 
 
TROUBLESHOOTING 
Common Problems and Solutions 
These guidelines provide tips to deal with problem s you may encounter while using the projector. If 
the problem remains unsolved, contact InFocus at 
www.infocus.com/support. 
Often the problem is traced to something as simple as a loose connection. C heck the following before 
proceeding to problem-specific solutions. 
•  Use another electrical device to confirm that the electrical outlet is working. 
• Ensure the projector is turned on. 
• Ensure all connections are securely attached.  
• Ensure the attached device is turned on. 
• Ensure a connected PC is not in standby mode. 
• Ensure a connected notebook computer is configured for an external display. 
(This is usually done by pressing a Fn-key combination on the notebook. 
Tips for Troubleshooting 
In each problem-specific section, tr y the steps in the order suggested. This may help you to solve the 
problem more quickly. 
Try to pinpoint the problem and avoid  replacing non-defective parts.  
For example, if you replace battery and the problem remains, put the original battery back and go to 
the next step.  
Keep a record of the steps you take when troubles hooting. The information may be useful when call-
ing Technical Support and obtaining service. 
  
						

							
IN1124/IN1126 – User’s Manual 
  – 37  – 
LED Error Messages 
Error Code Messages POWER LED  OVER TEMP 
LED READY LED 
Overheating Off Solid  Red Off 
Thermal break status error Flashing Green 4x Off Off 
Lamp error Flashing Green 5x Off Off 
Fan1 error (Power Fan) Flashing Green 6x Off Flashing Orange 1x
Fan2 error (Lamp Fan) Flashing Green 6x Off Flashing Orange 2x
Fan3 error (Blower Fan) Flashing Green 6x Off Flashing Orange 3x
Lamp door open Flashing Green 7x Off Off 
DMD error Flashing Green 8x Off Off 
Color wheel error Flashing Green 9x Off Off 
In the event of an error, please  disconnect the AC power cord and wait for one (1) minute before re-
starting the projector. If the POWER or READY LED  is still blinking or the OVER TEMP LED is lit, 
contact InFocus Technical Support at 
www.infocus.com/support. 
Image Problems 
Problem: No image appears on the screen 
1.  Verify the settings on your notebook or desktop PC. 
2. Turn off all equipment and power up again in the correct order. 
3. Many laptops do not automatically turn on t heir external video port when a projector is 
connected. Usually a key combination like FN + F8  or CRT/LCD key turns the external 
display on and off. Locate a function key label ed CRT/LCD or function key with a monitor 
symbol. Press FN and the labeled function key simultaneously. 
Problem: The image is blurred  
1.  Adjust the  Focus on the projector. 
2. Press the  Auto button on the remote control or projector keypad. 
3. Ensure the projector-to-screen distance is with in the projection range. (Within 7m/23 for 
the standard lens; within 20m/66 for the long lens and within 3m/10 for the short lens). 
4.  Check that the projector lens is clean. 
Problem: The image is wider at the top or bottom (trapezoid effect)  
1. Position the projector so it is as perpendicular to the screen as possible.  
2. Use the  Keystone buttons on the remote control or projector to correct the problem. 
Problem: The image is reversed  
Check the  Projection setting in the Installation1 menu of the OSD. 
Problem: The image is streaked  
1. Set the  Frequency  and Tracking  settings on the  Computer menu of the OSD to the de-
fault settings. 
2.  To ensure the problem is not caused by a connected PC’s video card, connect to another 
computer.  
  
						

							
User’s Manual 
– 38 – 
Problem: The image is flat with no contrast  
Adjust the  Contrast setting on the Image  menu of the OSD. 
Problem: The color of the projected image does not match the source imag\
e. 
Adjust the Color Temperature  and Gamma settings on the  Image menu of the OSD. 
Lamp Problems 
Problem: There is no light from the projector  
1. Check that the power cable is securely connected. 
2. Ensure the power source is good by te sting with another electrical device. 
3. Restart the projector in the correct order an d check that the Power LED is solid green. 
4. If you have replaced the lamp recently,  try resetting the lamp connections.  
5. Replace the lamp module. 
6. Put the old lamp back in the projector and have the projector serviced. 
Problem: The lamp goes off 
1. Power surges can caus e the lamp to turn off. Unplug and re-plug the power cord and 
press the Power button. 
2.  If the lamp still does not ignite, unplug the projector and allow it to cool for 60 minutes. 
Replace the lamp. 
3. If a new lamp does not resolve the issue, put t he old lamp back into the projector and ar-
range to have the projector repaired. 
Remote Control Problems 
Problem: The projector does not respond to the remote control  
1.  Direct the remote control towards remote sensor on the projector.  
2. Ensure the path between remote and sensor is not obstructed. 
3. Turn off any fluorescent lights in the room. 
4. Check the battery polarity. 
5. Replace the battery. 
6. Turn off other infrared-enabled devices in the vicinity. 
7. Replace the remote control.  
						

							
IN1124/IN1126 – User’s Manual 
  – 39  – 
Audio Problems 
Problem: There is no sound 
1.  Adjust the volume with the remote control.  
2. Adjust the volume of the audio source. 
3. Check the audio cable connection. 
4. Disconnect audio out cable. 
5. Test the source audio output with other speakers. 
6. Have the projector serviced. 
Problem: The sound is distorted  
1. Check the audio cable connection. 
2. Test the source audio output with other speakers. 
3. Have the projector serviced. 
Having the Projector Serviced 
If you are unable to solve the problem  contact InFocus Technical Support at www.infocus.com/support. If 
your projector needs repair, pack the projector in th e original carton and include the return authorization 
number on the outside of the box. 
   
						

							
User’s Manual 
– 40 – 
HDMI Q & A 
Q. What is the difference between a “Standard” HDMI cable and a “High-Speed” HDMI 
cable? 
Recently, HDMI Licensing, LLC announced that  cables would be tested as Standard or High-
Speed cables.  
˙ Standard (or “category 1”) HDMI cables have b een tested to perform at speeds of 75Mhz or 
up to 2.25Gbps, which is the equivalent of a 720p/1080i signal.  
˙ High Speed (or “category 2”) HDMI cables have been tested to perform at speeds of 340Mhz 
or up to 10.2Gbps, which is the highest bandwidth  currently available over an HDMI cable and 
can successfully handle 1080p signals including those at increased color depths and/or 
increased refresh rates from the Source. High-Speed cables are also able to accommodate 
higher resolution displays, such as WQXGA cinema monitors (resolution of 2560 x 1600). 
 
Q. How do I run HDMI cables longer than 10 meters? 
There are many HDMI Adopters working on HDMI  solutions that extend a cable’s effective 
distance from the typical 10 meter range to much longer lengths. These companies 
manufacture a variety of solutions that includ e active cables (active electronics built into 
cables that boost and extend the cable’s signal), repeaters, amplifiers as well as CAT5/6 and 
fiber solutions. 
 
Q. How can I tell if a cable is an HDMI certified cable? 
All HDMI products are required to be certified  by the manufacturer as part of the HDMI 
Compliance Test Specification. However, ther e may be instances where cables bearing the 
HDMI logo are available but  have not been properly tested. HDM I Licensing, LLC actively 
investigates these instances to ensure that  the HDMI trademark is properly used in the 
market. We recommend that consumers buy  their cables from a reputable source and a 
company that is trusted. 
 
For more detailed information, go to: http://www.hdmi.org/lear ningcenter/faq.aspx#49 
						

							
IN1124/IN1126 – User’s Manual 
 
 
SPECIFICATIONS 
Specifications   
Model IN1124 IN1126 
XGA 0.55” WXGA 0.65” Display type 
1024x768 1280x800 Native Resolution  
Projection distance 1.5 meters ~ 10 meters ( 4.92 ft ~ 32.81 ft ) (standard lens) 
Projection screen size  27 ~ 207 ( 68.58cm ~ 525.78cm )34 ~ 257 ( 86.36cm ~ 652.78cm )(standard lens) 
Manual Focus/Manual Zoom Projection lens 
Zoom ratio (standard lens) 1.15x 
Vertical keystone correc-+/- 15 degrees tion 
Front, Rear, Desktop/Ceiling (Rear, Front) Projection methods 
VGA, SVGA, XGA, SXGA, SXGA+, UXGA, Mac Data compatibility 
480i, 480p,576i, 576p, 720p, 1080i, 1080p SDTV/ EDTV/ HDTV 
NTSC 4.43, PAL (M/N/60), SECAM Video compatibility 
15K, 30 – 91.4 KHz H-Sync 
43 – 87 Hz V-Sync 
FCC-B, UL, cUL, CB, CE, CCC, PCT, PSB, SABS, NOM, CECP, SASO, 
Tuv-GS, KC, UL-s for Argentina and C-TICK Safety certification 
5° ~ 35°C ( 41° ~ 95°F) Operation temperature 
220.00mm x 178.00mm x 71.00mm (8.66” x 7.01” x 2.80”) Dimensions (W x D x H) 
AC Universal 100-240, Typical @ 110VAC (100-240)/ 10% ±AC Input 
Normal mode: 280W / ECO mode: 230W Power consumption 

						

							
User’s Manual 
Projection Distance vs. Projection Size 
For XGA 
Screen Width
Projection Distance 
AImage Height
 
Projection Distance and Size Table 
TELE WIDE IN1124 
Distance 
 (m/inch) 1.56/ 
61.424.47/ 
175.98 7.15/ 
281.59.83/ 
387.011.54/ 
60.633.86/ 
151.97 7.72/ 
303.9411.58/ 
455.91
Diagonal  
(cm/inch) 88.9/ 
35 254/ 
100 406.4/ 
160558.8/ 
220101.6/ 
40254/ 
100 508/ 
200 762/ 
300
Image Height 
(cm/inch) 53.34/ 
21 152.4/ 
60 243.84/ 
96335.28/ 
13260.96/ 
24152.4/ 
60 304.8/ 
120 457.2/ 
180
Image Width 
(cm/inch) 71.12/ 
28 203.2/ 
80 325.12/ 
128447.04/ 
17681.28/ 
32203.2/ 
80 406.4/ 
160 606.9/ 
238.94
7.4/ 
2.9121.2/ 
8.35 33.9/ 
13.3546.6/ 
18.358.5/ 
3.3521.2/ 
8.35 42.4/ 
16.6963.6/ 
25.04A (cm/inch) 
TELE WIDE IN1126 
Distance  
(m/inch) 1.52/ 
59.844.55/ 
179.13 7.58/ 
298.439.86/ 
388.191.65/ 
64.963.3/ 
129.92 6.59/ 
259.459.89/ 
389.37
Diagonal  
(cm/inch) 101.6/ 
40 304.8/ 
120 508/ 
200660.4/ 
260127/ 
50254/ 
100 508/ 
200 762/ 
300
Image Height 
(cm/inch) 53.85/ 
21.2161.54/ 
63.6 269.24/ 
106350.01/ 
137.867.31/ 
26.5134.62/ 
53 269.24/ 
106 403.86/ 
159
Image Width 
(cm/inch) 86.16/ 
33.92258.47/ 
101.76 430.78/ 
169.6560.02/ 
220.48107.7/ 
42.4215.39/ 
84.8 430.78/ 
169.6646.17/ 
254.4
6.1/ 
2.4 18.3/ 
7.2 30.6/ 
12.0539.7/ 
15.637.6/ 
2.9915.3/ 
6.02 30.6/ 
12.0545.8/ 
18.03A (cm/inch) 
 
  
– 42 –
  
						

							
IN1124/IN1126 – User’s Manual 
  – 43  – 
Timing Mode Table 
The projector can display several resolutions. The  following table outlines the resolutions that can be 
displayed by the projector. 
SIGNAL RESOLUTION H-SYNC 
(KHZ) 
V-SYNC
(HZ) 
COMPOSITE 
/ S-VIDEO
VGA 
(ANALOG) 
HDMI 
(DIGITAL)
NTSC － 15.734 60.0  ○ － － 
PAL/SECAM － 15.625 50.0 ○ － － 
720 x 400 37.9 85.0 － ○ ○ 
640 x 480 31.5 60.0 － ○ ○ 
640 x 480 37.9 72.8 － ○ ○ 
640 x 480 37.5 75.0 － ○ ○ 
640 x 480 43.3 85.0 － ○ ○ 
800 x 600 35.2 56.3 － ○ ○ 
800 x 600 37.9 60.3 － ○ ○ 
800 x 600 46.9 75.0 － ○ ○ 
800 x 600 48.1 72.2 － ○ ○ 
800 x 600 53.7 85.1 － ○ ○ 
1024 x 600 37.3 60.0 － ○ ○ 
1024 x 768 48.4 60.0 － ○ ○ 
1024 x 768 56.5 70.1 － ○ ○ 
1024 x 768 60.0 75.0 － ○ ○ 
1024 x 768 68.7 85.0 － ○ ○ 
1280 x 720 45.0 60.0 － ○ ○ 
1280 x 720 90.0 120.0 － ○ ○ 
1280 x 800 49.7 59.8 － ○ ○ 
1280 x 800 62.8 74.9 － ○ ○ 
1280 x 800 71.6 84.8 － ○ ○ 
1280 x 1024 64.0 60.0 － ○ ○ 
1280 x 1024 80.0 75.0 － ○ ○ 
1280 x 1024 91.1 85.0 － ○ ○ 
1280 x 960 60.0 60.0 － ○ ○ 
1280 x 960 85.9 85.0 － ○ ○ 
1400 x 1050 65.3 60.0 － ○ ○ 
1440 x 900 70.6 75.0 － ○ ○ 
1440 x 900 55.9 60.0 － ○ ○ 
VESA 
1600 x1200 75.0 60 － ○ ○ 
640 x 480 35.0 66.7 － ○ ○ 
832 x 624 49.7 74.5 － ○ ○ 
1024 x 768 60.2 74.9 － ○ ○ 
Apple  
Macintosh 
1152 x 870 68.7 75.1 － ○ ○